WaterLogic WL100 Instrucciones de funcionamiento

WL100ManualPage64Revision:1‐14‐2019

HOTWATERTROUBLESHOOTINGINDEX



1. Hot Water is not Hot 85°C ± -15°C (185° ± 5° F)

Also includes related instructions for:

 Programming - Disabling Energy Saving Sleep Mode

 Resetting the Hot Tank Overload or High Limit Safety

 Programming - Changing Hot Water Mode to Ambient Water



1. HotWaterisnotHot85°C±‐15°C(185°±5°F)



TheHotTemperaturesetpointis85°C(185°F)andiscontrolledbyathermostatonthesideof

theHotTank.



ThereisaresettableoverloadorhighlimitsafetyabovethethermostatonthesideoftheHot

Tankthatwilltriptopreventdamagetotheunitifthetankisdryheated(turnedonwithout

waterinit).



TheWL100WaterTreatmentSystemisprogrammabletomakeCold/Ambientwater–referto

DisablingSleepModeinstructionsincludedfurtherbelowinthisTroubleshootingSection.



TheWL100WaterTreatmentSystemdoesNOThaveExtraHotcapabilityandthemaximumhot

temperatureis87°C(189°F).



Ittypicallytakes10minutesforthe500Wtoheatthe1.6Liter(0.4Gallon)ofroomtemperature

(ambient)watertothe85°C(185°F)setpoint.



PossibleReason Solution

NopowertoHeaterelements

CheckthattheRedHeaterandCompressorswitchis

on.



TurnRedHeaterandCompressorSwitchon.

I=ON

Isunitinsleepmode?

Ifnowaterhasbeendispensedfor3ormorehours,unitgoesinto

sleepmode.Dispensehotwater,wait5minutes,check

temperature.



Ifunitstilldoesnotheatproceedto“NopowertoHeater

elements”below.



IfunitdoesheatbutyouwouldliketoDisableSleepMode,refer

totheinstructionsincludedfurtherbelowinthisTroubleshooting

Section

WL100ManualPage65Revision:1‐14‐2019

HotTankOverloadTripped



Overloadisasafetyfeatureto

ensurethetankdoesnot

overheat.

Overloadwill“click”whenpushed.Theoverloadisautomatically

resetwhenpressed.



SeeResettingtheHotTankOverloadorHighLimitSafety

Instructionsthatareincludedfurtherbelowinthis

TroubleshootingSection

EnergySaverPCBRelayBoard

ConnectorBad



Inspectconnectorfordiscoloration.

Ifthereisnodiscoloration,contactWaterlogic

TechnicalDepartment.



Thermostatoroverload

“open”onHotTank

TurnPoweroff.CheckOHM’sresistanceacrossterminalsoneach

ThermostatandOverloadseparately.



GoodcomponentswillindicateaclosedcircuitorzeroOHM’son

themeter.



Replacecomponentsasnecessary.

Looseorimproperly

connectedwire(s)tothe

heatingelement/HotTank.

VisuallyinspectwireleadsgongtotheHotTank;confirmproper

connectionstotheheatingelements.



HotTanklifeis3‐5yearsdependingonusage,dependingon

usage.



*Typically,dealersswapouttheHotTankatsite,takebacktothe

shoptorepair.

HeatingCoilNotWorking

TurnPoweroff;DrainHotTank;Usemulti‐metertocheckHeater

elementforapproximately26OHM’sresistance.



HotTankmustbeemptyifyouarecheckingforcontinuity.



ReplaceHotTankasnecessary.

ImproperJumperSettings



Theunithasbeenchangedtoacold/ambientsetting(JP9hasbeen

movedfromPin1andPin2).



VerifythatJumperPinsarelocatedproperlyforHotWaterOption.



SeeChangingHotWaterModetoAmbientWaterInstructions

includedfurtherbelowinthisTroubleshootingSection





WL100ManualPage66Revision:1‐14‐2019

PROGRAMMING“DISABLINGENERGYSAVINGSLEEPMODE”

AllWL100WaterTreatmentSystemscomefromthefactorywithEnergySavingSleepMode

engagedtomeettheEnergyStarCertificationrequirements.EnergyStarSleepModedisables

theHeaterCircuitifthehotdispensehasnotbeenusedfor3hours.

Selectinganybutton"wakesup"theWL100WaterTreatmentSystemandturnstheHeater

circuitbackon.TheHotTankwilltypicallytakelessthan10minutestoheatthewaterfrom

ambienttothe85°C(185°F)setpoint.

UnplugPowerCordandremoveTopCovertoaccessEnergySaverPCB.



ENERGYSAVINGSLEEPMODE

ON OFF

PCBJumperJP7(PinNumbers1and2)



PCBJumperJP7(PinNumbers2and3)



EnergySaverPCB–PN20‐0075–FactoryPNEN‐6131

JP7

1 2 3

JP7PINNUMBERS

1 2 2 3

WL100ManualPage67Revision:1‐14‐2019

RESETTINGTHEHOTTANKOVERLOADORHIGHLIMITSAFETY



 

1. RedCompressor/HeaterSwitchmustbeintheO=OFFposition

2. UnplugthePowerCordfromrearofunit.

3. RemovetheLowerFrontPanelofunitbyremovingthePhillipsheadscrewsunderneath

theLowerFrontPanel.

4. LocatetheProtectiveMetalBoxontherearoftheHot

Tank.AsyoulookthroughtheCondensercoilsonthe

rearoftheunit,youwillseetheHotTanklocatedon

theright‐handside.



5. FromthefrontoftheWL100WaterTreatmentSystem,

reachupbehindtheHotTankandtakeholdofthe

ProtectiveMetalBoxcoveringtheThermostatand

overloadontheHotTank.



TherearenutsthatsecuretheProtectiveMetalBoxto

theHotTank,arelooseenoughtoallowyoutoremove

theProtectiveMetalBox.



Ifthenutsonthemetalboxaretootight,loosenthe

nutssecuringtheHotTanktotheUpperBaseofthe

WL100WaterTreatmentSystemunitandlowerthe

HotTanksoyoucanremovetheProtectiveMetalBox.



WL100ManualPage68Revision:1‐14‐2019

6. Fordemonstrativepurposes,photosbelowhaveloweredtheHotTankfromtheunit.



Presstheresetbutton



7. ReattachtheProtectiveMetalBoxbydepressingthetop

flapoftheProtectiveMetalBoxsoitsnapsbackintoits

originalpositionontheHotTank. 

8. ReplacetheLowerFrontPanel.

9. PluginthePowerCord.

10. TurnontheRedCompressor/HeaterSwitchI=ONposition



TheHotandColdTanksmustbefilledwithwaterBEFOREturningonthe

RedHeaterandCompressorSwitch.



11. Verifythecoolerisfullyoperationalbeforeinstallingitatthecustomers’site.





WL100ManualPage69Revision:1‐14‐2019

PROGRAMMING“CHANGINGHOTWATERMODETOAMBIENTWATER“



TheWL100WaterTreatmentSystemcomeswithsettoHot/Cold,whichcanbechangedto

Ambient/Coldsettings.OntheEnergySaverPCB,movetheJumperonJP9fromPins1and2to

Pins2and3.



UnplugPowerCordandremoveTopCovertoaccessEnergySaverPCB.



HotandCold(FactorySettings) AmbientandCold

PCBJumperJP9(PinNumbers1and2)



PCBJumperJP9(PinNumbers2and3)



EnergySaverPCB–PN20‐0075–FactoryPNEN‐6131

JP9

1 2 23

JP9PINNUMBERS

123

Otros manuales para WL100

Otros manuales de Sistema de filtración de agua de WaterLogic

WaterLogic

WaterLogic WL270 Manual de usuario

WaterLogic

WaterLogic WL500 - Sparkling Manual de usuario

WaterLogic

WaterLogic WL7 Manual de usuario

WaterLogic

WaterLogic PUREZZA WL2FL FIREWALL Manual de usuario

WaterLogic

WaterLogic WL500 - Sparkling Manual de usuario

WaterLogic

WaterLogic WL100 Guía de referencia

WaterLogic

WaterLogic WL15-HCS Manual de usuario

WaterLogic

WaterLogic WL2FL FIREWALL Manual de usuario

WaterLogic

WaterLogic F-FWEG1-M-A-NT Series Manual de usuario

WaterLogic

WaterLogic WL100 Instrucciones de funcionamiento

WaterLogic

WaterLogic Countertop Pure K-FU-00S20-00C1L-13-0-XXX Manual de usuario

WaterLogic

WaterLogic WL7 FW Guía de referencia

WaterLogic

WaterLogic WL3 FX Manual de usuario

WaterLogic

WaterLogic WL270 Manual de usuario

WaterLogic

WaterLogic F-FWEG1-M-A-NT Series Manual de usuario

WaterLogic

WaterLogic Water Filtration Systems Manual de usuario

WaterLogic

WaterLogic WL270 Manual

WaterLogic

WaterLogic WLH2 Classe Manual de operación y mantenimiento

WaterLogic

WaterLogic WL15 Manual de usuario

WaterLogic

WaterLogic WL850HV Manual de usuario

WaterLogic

WaterLogic WL3 IT Manual de usuario

WaterLogic

WaterLogic WL380 Instrucciones de funcionamiento

WaterLogic

WaterLogic WL7 Manual de usuario

WaterLogic

WaterLogic WL380 Manual de usuario

Manuales populares de Sistema de filtración de agua de otras marcas

Wisy

Wisy LineAir 100 Manual de usuario

Schaffner

Schaffner Ecosine FN3446 Series Manual de funcionamiento

Pentair

Pentair FLECK 4600 SXT Guía del usuario

H2O International

H2O International H20-500 Manual de usuario

Renkforce

Renkforce 2306241 Manual de usuario

Neo-Pure

Neo-Pure TL3-A502 Manual de usuario

FLTR

FLTR OBF Manual de usuario

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Manual de usuario

Applied Membranes

Applied Membranes W-G844EM Manual de usuario

BEGA

BEGA 116 Manual de usuario

WATA

WATA Standard Manual de usuario

Price

Price FFU series Manual

Gaggenau

Gaggenau BRITA INTENZA 467873 Manual de usuario

Brita

Brita SAFF-100 Manual de usuario

HEISSNER

HEISSNER FPU24000-00 Manual de usuario

BGS technic

BGS technic 1518 Manual de usuario

Reverse Osmosis

Reverse Osmosis RF Series Manual de usuario

ubbink

ubbink Filtramax Series Manual de usuario