Waterhouse XC-SP1606 Manual de usuario

12 Volt Hot Water Circulation Pump User Guide Manual

Model: XC-SP1606

Caution:

Please read all instructions carefully before installing this product.

This pump is not ip68 sealed and therefore shall by any means never be submerged.

However, the electric wire connections must not be submerged. For extra protection please

insulate all joins and ends with approved insulation or shrink tapes to avoid electric shocks

and fire sparks that may cause explosions or fires.

Security:

•12V brushless pumps can only be used for pumping clean cold and hot water and

non-corrosive chemicals and liquids.

•Please connect pump’s black and white wire to the negative terminal (-) and white

wire to the positive terminal (+).

•Make sure you use suitable size fuses.

•The wire connections must be insulated by shrink or watertight insulation tape.

•All wire connections must be outside water, unless necessary provided you have an

ip68 waterproof connector.

•Please do not run the pump dry.

•Your pump must always be protected from water splashes or any liquid chemicals.

•Make sure the pump works in a ventilated environment.

About product:

•Circulation pump is non-self-priming pump. Max Flow Rate: 20L/MIN, Max Discharge

Head: 6M

•10mm male adapter on the pump.

•Power source: DC 12V (NOT INCLUDED), Rated current: 2.0A, Brushless Motor, Low noise:

30db at 1 metre, Service life: 30000 hours.

•Max circulating water temperature: 100°C

•Do no submerge.

Specifications:

Model

Flow Rate

Volt

Current (A)

Head (m)

Cable

Outlet Dia

Weight

XC-

SP1606

20L/MIN

3.3AMP

6.0

20cm

10mm

0.30kgs

Warning:

•To prevent injury, always disconnect the power source when installing or servicing

any electric product.

•Do not use the pump-to-pump gasoline oil or any flammable liquids.

•Always make sure you use fuse amperage rated for your pump model.

•Failure to follow these instructions may result in serious injury or fire hazards.

Optional Materials:

•Mounting screws

•Mounting brackets.

Pump Mounting Instructions:

Warning: remove any polystyrene or foam blocks covering the pump around for

shipping purposes.

•Step 1: make sure you mount the pump wit5h safety brackets, make sure it is

holding firmly as to avoid too much vibration that will affect your seals and bearings.

•Step 2: now insert your hose inlet/outlet and use hose clamps to secure the pipes.

•Step 3: now you can link your inlet pipe to the water source and outlet to the supply,

you must always watch for the inlet/outlet arrow when installing this type of pump.

•Step 4: make sure your pump is at bottom of the water level as is the pump is not

self-priming.

•Step 5: make sure you pump is covered or protected from water or rains never

submerge the pump.

Pump mounting:

Operation:

1. Connect your -+ terminals accordingly to your battery positive and negative poles.

2. Make sure you have right size fuse on your positive pole.

3. Connect your pump to the control switch, depending on what operation you are

using the pump for:

•Use manual or thermostat switches for pump control.

Care & Maintenance:

•Always watch your power supply voltage or current for over voltage, under voltage

or short circuit.

•Make sure your pump filter sieve is always clean of debris or any clogging dirty.

•Careful attention will guarantee outstanding pump performance.

Parts:

For more information, please feel free to contact us on 011 466 8520 or email

us at [email protected]a

Tabla de contenidos

Otros manuales de Bomba de agua de Waterhouse

Waterhouse

Waterhouse XC-SP006-FL35 Manual de usuario

Waterhouse

Waterhouse XC-SP002 Manual de usuario

Waterhouse

Waterhouse WH150 Manual de usuario

Waterhouse

Waterhouse XC-SP08301 Manual de usuario

Waterhouse

Waterhouse XC-SP005 Manual de usuario

Waterhouse

Waterhouse XC-SP003-FL40 Manual de usuario

Waterhouse

Waterhouse XC-SP0703 Manual de usuario

Waterhouse

Waterhouse FL-800 Manual de usuario

Waterhouse

Waterhouse XC-SP2502 Manual de usuario

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario