Wasserstein Smart Floodlight Manual de usuario
Smart Floodlight
User Manual
Page 1
In the Box
1 x smart floodlight
1 x ring and nut set
2 x machine screws
(M4 * 25mm)
3 x wire nuts
1 x crossbar
1 x EVA gasket
• As the temperature changes, the detection distance will be
affected.
• Do not mount the near a heat source like an air conditioner,
vent, furnace, exhaust, or in a direction facing any reflective
object / other nearby light source.
• Shut off power at the circuit breaker or fuse panel before
removing the old fixture or installing the new one.
• LEDs can be damaged by electric static. Before installing,
discharge any static from your body by touching a grounded
bare metal surface.
• To avoid damage, do not remove the clear lens over the LED
module.
Page 2
• Please read this entire manual before attempting to
assemble, operate, or install the product.
• Floodlight MUST be installed by a qualified electrician.
• Turn power OFF before installing.
• Do NOT touch or install fixture near water or if the
surrounding area is wet.
• Do NOT remove the protective LED lens.
• Do NOT look directly at lit LEDs for any length of time.
• Do NOT leave bare wires exposed.
• Electrical requirements: 120V, 60 Hz
• Do NOT allow the sensor head to touch the LED head
housing. Maintain at least 1 inch of space between the LED
heads and the sensor head.
• For proper operation and protection against water damage,
the motion sensor adjustment controls MUST be facing
downward.
• Do NOT mount below 5 ft.
Safety Instructions
Warnings
Page 3
2. Remove the protective layer from the EVA gasket and stick it
firmly on the back of the floodlight (make sure the long screw
at the crossbar goes through the center hole and the wires go
through the gasket opening).
Caution:
The floodlight must be installed by a qualified electrician. Your
main circuit breaker MUST be turned off before installing.
How to Install
1. Attach the crossbar to the junction box using the two machine
screws provided.
Page 4
3. Connect the yellow/green (ground) wire from the floodlight to
the junction box using the ground screw (painted green).
Connect the white wires (neutral) with a wire nut. Connect the
black wires (hot) with a wire nut.
4. Carefully place wires into the junction box. Place floodight
over the crossbar. Mount the floodlight onto the crossbar and
secure it with the nut and ring provided.
Note:
For further weatherproofing, fill all gaps with a sealing compound
or silicon glue.
Page 5
Minimum requirements:
• Smartphone or tablet running iOS 9.0 or later / Android
5.0 or later.
• 2.4 GHz WiFi Network (not compatible with 5 GHz
connections).
• Upload speed of at least 2 Mbps.
1. Download the App by scanning the QR code or by searching
"Wasserstein App" in Google Play or the App Store.
2. Sign up for a new account or log in to an existing account.
3. Click "Add Device" or "+" in the top right corner. You can add
your device by selecting "Add Manually" or "Auto Scan".
App Setup
Page 6
Figure 1
Flash Dim Flash Dim
1. Select "Lighting" - "PIR Light（BLE+WiFi)".
2. Reset the floodlight by turning it on and off in the following
sequence: on-off-on-off-on (steps also displayed in your App).
Then, your floodlight will flash in intervals (Figure 1).
Add Manually
selection
If the light is flashing already,
please skip the reset steps.
Resetting the device:
1. Power on the device.
2. Turn on-off-on-off-on.
3. Make sure the light is flashing.
Note: Please complete the network
selection within 3 minutes after
resetting the device.
Confirm that the light is flashing.
Page 7
3. Enter your WiFi details, and click "Confirm".
4. Wait until your device has been added successfully.
Wasserstein Smart Floodlight
WiFi Login
WiFi Password
Page 8
1. Reset the floodlight to enable pairing mode. Turn on and off
in the following sequence: on-off-on-off-on. Your floodlight
will then flash in intervals.
2. Wait until your floodlight has been automatically detected.
Auto Scan
Note: Display and interface are subject to change.
Sensor
Manual
On/Off
Light intensity
Floodlight color
Turn on/off timer
Schedule
Sensor
On/Off
Motion detection range
Floodlight light sensitivity
Duration of light flash
Event records
1. Settings
App Functions
Page 9
Tabla de contenidos
Otros manuales de Foco de Wasserstein
Wasserstein
Wasserstein 3-in-1 Smart Floodlight, Charger & Mount for Wyze Cam... Manual de usuario
Wasserstein
Wasserstein 3-in-1 Smart Plug-in Floodlight for Blink... Manual de usuario
Wasserstein
Wasserstein Floodlight with Charger Manual de usuario
Wasserstein
Wasserstein 3-in-1 Wired Floodlight, Charger and Mount for Blink Outdoor /... Manual de usuario
Wasserstein
Wasserstein Noorio Spotlight Cam B210 Manual de usuario
Wasserstein
Wasserstein 2 in 1 - Solar Charger & Security Light Manual de usuario
Wasserstein
Wasserstein 3-in-1 Smart Floodlight, Charger & Mount for Blink Outdoor & Blink XT... Manual de usuario
Wasserstein
Wasserstein 3-in-1 Smart Plug-in Floodlight for Arlo Pro 3/Pro 4 and Arlo Ultra/Ultra... Manual de usuario
Wasserstein
Wasserstein Solar Floodlight & Charger with Micro USB... Manual de usuario
Wasserstein
Wasserstein Floodlight For Google Nest Cam Manual de usuario
