Wasp WWS150i Manual de usuario
1
WWS150i
Quick Start Guide
Table of Contents
Quick Start 2
1. Unpack 2
2. Charging the WWS150i 2
3. Connecting the Scanner to a Bluetooth Device 2
Setup & Configuration 3
Factory Default 4
Check Version 4
Link Quality On/Off 4
Set Connection 4
Bluetooth SPP (Bluetooth COM) 5
Bluetooth HID (Keyboard) 5
Terminator 6
iPad/iPhone Toggle Keyboard 6
Enable/Disable iOS Hotkeys 7
QSG
2
QSG
2
Quick Start
1. Unpack
Open the box and remove all the pieces from their protective packaging.
2. Charging the WWS150i
You must charge the scanner for 4 hours before first using it. To charge
the scanner, plug the power supply into the bottom of the scanner.
3. Connecting the scanner to a Bluetooth device
The scanner will connect to most Bluetooth devices that support HID
connection.
You will need to open your Bluetooth software and search for Bluetooth
devices. The Bluetooth software can be found by clicking the Bluetooth
symbol on the start bar near the computer time.
QSG
2 3
QSG
2
In order to configure Wasp WWS150i Freedom Scanner, familiarize
yourself with the setup procedures on the following pages. The default
settings of the scanners are identified on each page and clearly marked
using an asterisk (*). The default settings have been preprogrammed for
the most common barcode configurations. Use the setup & configuration
barcodes only to customize the WWS150i Freedom Scanner settings. If
you need to configure the Scanner, the default settings will be overwritten.
All the programmed settings are stored permanently in non-volatile
memory.
In order to configure Wasp WWS150i Freedom Scanner,
two basic steps need to be followed:
(1) Locate the group that contains the options to be changed.
(2) Scan the barcode representing the option to be changed.
The scanner will sound two beeps.
Setup & Configuration
QSG
4
Use the Factory Default barcode to reset the scanner to the Default settings.
Factory Default
Check Version
Scan the Check Version barcode to verify your current firmware’s version number.
Check Version
Factory Default
Link Quality affects the transmission quality. When Link Quality is turned
on (default setting), data transfer is more secure, but slower. If you notice
that your transmissions to the host are too slow, you can try turning the
Link Quality setting to off.
Link Quality On/Off
Link Quality On* Link Quality Off
Set Connection
Scan this barcode to break your current connection and enable your device
to connect to a new Bluetooth host.
Set Connection
QSG
54
Bluetooth SPP (Bluetooth COM)
The Bluetooth SPP (Serial Port Protocol) creates a virtual Bluetooth
comport. This setting is not recommended. Only use this option if you
have software capable of capturing data off of a comport.
Bluetooth SPP (Bluetooth COM)
Bluetooth HID
Use this setting (on by default) to pair with most Bluetooth connections.
Bluetooth HID works just like a keyboard.
Bluetooth HID*
QSG
6
Terminator
The ‘Terminator’ option is used to specify the end-of-text message and is
primarily used to denote the end of the barcode value.
CR *
None
LF
CR + LF
TAB
Space
ESC
iPad/iPhone Toggle Keyboard
Scan this barcode to display or hide the on-screen keyboard when
connected to an iPad or iPhone.
iPad/iPhone Toggle Keyboard
QSG
7
connection
6
Enable/Disable iOS Hotkey
Use these barcodes to enable or disable the iOS hotkey on your device.
When the iOS hotkey is enabled, you can double-click the trigger to toggle
the iPhone/iPad Touch Keyboard.
Enable iOS Hotkey
Disable iOS Hotkey
*
8
Wasp®Barcode Technologies
1400 10th Street, Plano, Texas 75074
Tel: 214.547.4100 • Fax: 214.547.4101
www.waspbarcode.com
Otros manuales para WWS150i
1
Tabla de contenidos
Otros manuales de Lector de código de barras de Wasp
Wasp
Wasp WWS650 Manual de usuario
Wasp
Wasp WDI4700 Manual de usuario
Wasp
Wasp WWS750 Manual de usuario
Wasp
Wasp WDI9600 Manual de usuario
Wasp
Wasp WWS450 Manual de usuario
Wasp
Wasp WPL608 Manual de usuario
Wasp
Wasp WRS100SBR Manual de usuario
Wasp
Wasp WLS8600 Manual de usuario
Wasp
Wasp WLS9600 Manual de instalación y operación
Wasp
Wasp CCD Scanner Instrucciones de funcionamiento
Wasp
Wasp N1181 Instrucciones de funcionamiento
Wasp
Wasp WPS1500 Manual de usuario
Wasp
Wasp WLP 4170 Manual de usuario
Wasp
Wasp WLP 4170 Instrucciones de funcionamiento
Wasp
Wasp WWS500 Instrucciones de funcionamiento
Wasp
Wasp Bar Code Laser Instrucciones de funcionamiento
Wasp
Wasp 2D Manual de usuario
Wasp
Wasp WWS110i Manual de usuario
Wasp
Wasp WLS9600 Manual de usuario
Wasp
Wasp WPL25 Manual de usuario
