Warmset WHP Manual de usuario
Installation Manual
Warmset
Wall
heating
panel
Warmset srl
2
The Warmset Wall Heating System is an electrical appliance
and must be installed in accordance with the IEC
(International Electrotechnical Commission). It complies with
the laws EN60335-1 EN60335-20 EN50366
These instructions are available in digital format on the site
www.warmset.com
Dear Customer, Thank you for choosing
this Warmset product
The wall heating panel Warmset is an electrical device. It is very
important to read carefully these instructions before the use. For
any other information contact Warmset Srl. Keep this manual
with you and never entrust the panel to other peeople without
giving this instruction paper.
What is included:
•Wall heating panel
•Template for tracing holes in fixing elements
•Fixing system: a male bar-hook to be applied to the panel
(vertical or horizontal), female hook bar to be applied to the
wall, bar with magnets to be applied to the wall, 4 plugs and
4 fisher.
The Warmset heating panel is built to heat indoor environments
through radiation, not to use it for other purposes. Any other use
may cause damage to the panel and damage to people, animals
or things. In no case should it be covered with clothes or fabrics
in general.
The Warmset heating panel is an electric heating system by radiation,
which uses the Joule effect of the conductor inside (patented Warmset
system) to radiate heat. The panel converts all electricity into thermal
energy.
It has a setting time of a few minutes, based on the temperature of the
environment where it works. To reach the desired room temperature it
is recommended that the panel remains on for as long as necessary
once it reaches the operating temperature.
All the panels contain a thermal protector at 120 ° C which temporarily
blocks its operation in the event of overtemperature.
Product information
General
panel
informations
3
All the Warmset heating panels must be used only as heating
elements, both primary and not-primary; any other use of the
product can lead to significant damage to people, animals and the
environment.
Warmset heating panels are not designed to be used by
people with reduced physical, sensory or mental abilities, or with
lack of experience or knowledge, unless they are supervised by a
person responsible for their safety, or have received adequate
instructions on the use of the device.
All heating panels must be kept out of the reach of children. It is
recommended to supervise the children to make sure that they do
not play with the device. Warmset heating panels are not suitable
for outdoor use in the rain or in permanently wet conditions, under
water and for any other use not specified.
All the heating panels are equipped with a thermal protector at 120
° C which temporarily blocks operation in the event of overheating
(for example in the event of accidental covering of it).
•Don't cover the panel.
•The panel heats (max Temp. 95° C). It can cause skin burns in case
of prolonged contact
•Each panel is equipped with a plug mod. Shuko. Using a specific
adapter it is possible to integrate it with a room temperature
control.
•NEVER use the panel when the plug cable is damaged. Check this
before each use. Do not remove the plug by pulling on the cable;
may cause it to tear. Be careful not to rub the cable on sharp
edges. In the event of damage, contact Warmset Srl.
•NEVER immerse the heating panel in water.
•In the event of damage to the panel or the mains, immediately
disconnect the panel from the power supply.
•NEVER open the device to avoid damage and accidents. The
device can be open by authorized personnel. Failure to do so will
void the warranty
General warnings before the use
General
security
informations
Special
Security
Informations
01
4
Warmset Heating panels must be mounted with the Warmset fixing
system inside the package. For the panels that are used, without the
original suspension, could invalidate the Warmset warranty.
Make sure that the frame/wall can withstand the weight of the
corresponding panel (max 7 kg)
Proper ventilation on the rear of the heating panel shall be
ensured. Make sure not to place bulky objects at too close a distance
from it, or to cover the top or bottom parts of the panel
Under no circumstances drill holes or cuts into the panel
Make sure that the power cord during assembly is not connected.
If holes or tampering have been made for any reason, do not open the
device. Please contact the manufacturer or retailer where the product
was purchased.
If the device is installed in rooms or areas easily accessible by children,
make sure that the device is suspended at a minimum height of 1,2 m
above the ground.
Distance BACK: the Warmset system is a frontal irradiation system,
therefore on the back the temperature reached is 40C° lower than the
front. Do not recess onto plasterboard elements
Installation & user informations
2.1 Fixing
instructions
02
5
2.2 First using
information
2.3 Models
Installation & user informations
FRONT DISTANCE: Warmset panels radiate only on the front side.
Make sure there is a minimum distance of 250 mm towards the front
Do not put the heating element before or immediately under an
outlet.
Make sure the plug is accessible after installation of the panels and
that in case of emergency it can be immediately and easily removed
If the heating panel is permanently integrated into an electrical
system, a Category III overvoltage separation device is required
for complete separation. This connection must be made only by
qualified personnel.
To connect the heating panel to the mains, connect it to a socket in
a correct way, carefully following the SAFETY WARNINGS.
From the moment of its ignition the speed of the panel is variable
from 5 to 10 minutes depending on the internal temperature of the
operating environment.
During the first use, it is possible to perceive a slight plastic smell in
near the panel. This is not an anomaly, but a normal chemical break
of the paint.
02
Model Sizes Power Weight
WHP 90 x 60 x 1,3
cm
400 W 6 kg
WHP/S 90 x 60 x 1,3
cm
400 W 6kg
6
Under no circumstances should the panel be covered by clothes. Do
not use the panel for any other uses, only to heating.
During its operation, the heating and cooling cycle of the Warmset
heating panel can cause a slight swelling on the front of it. This
does not constitute an anomaly but is a mechanical/thermal
characteristic of the device.
The surface of the panel during its operation is very hot with a variable
temperature depending on the ambient 75 to 105°C. Prolonged contact
with it can lead to damage to things or people/animals.
If you do not use the panel, unplug the plug.
The panel must be clean.
Warmset panels do not require any maintenance. In the event of an
irregularity occurring when the package is opened or first used,
disconnect the plug immediately from the socket and contact the retailer.
To clean correctly the panel, follow the next instructions:
• unplug the plug before cleaning;
• the heating element is very hot as soon as the panel is switched off:
before cleaning the panel let it cold for at least 15 minutes;
• do not put the panel in water or the water on it. Do not use wet cloths.
Only use a dust trap or damp cloths;
• ensure that the panel is completely dry before the next ignition;
• do not use abrasive sponges, aggressive chemicals or rough cloths.
Heating panels with writing or customization should only be cleaned in a
dry mode.
2.4 Instructions
of use
2.5 Cleaning
and
maintenance
02 Installation & user informations
7
03
Recycling and disposal
The Warmset materials uses for the production of the panel and its
packaging comply with EU environmental standards and legislation.
For the correct disposal of materials, please follow these directions.
The packaging materials, made of cardboard, are recyclable in paper
containers.
The plastic components of packaging must be kept completely out of
reach of children.
Protective films for the packaging of the fastening kit must be
recycled in an appropriate manner according to the regulations
in force.
The heating panel must be delivered to the appropriate
environmental centres or disposal centres in accordance with
the regulations in force.
3.1 Recycling
and disposal
Warranty
Warmset guarantees the warranty of this product to
the original buyer for the period of twenty-four (24)
months from the invoice date. Warmset’s obligation
and exclusive remedy under the pre-trial warranty are
limited to repair or replacement, at Warmset’s
discretion, of any part of the product which may be
defective under conditions of use and maintenance
which comply with the verification. The full details of
the warranty can be found online at the address
www.warmset.com or contacting us at +39
0444/491328
04
0444Via Ettore Majorana 1 - 36075 Montecchio Maggiore / Vicenza — Italy T +39 0444 491328 F +39 496757
www.warmset.com
Quick installation guide
1
Installation Kit :
•
•
iron bracket upper part (A)
iron bracket lower part with
magnets (B)
•panel attachment bracket (C)
Wall fixing:
Take bracket A and fix it to the wall at the
desired height - Consider that this
bracket will be the main fastening of the
panel.
2
Therefore also fix the bracket B (with
magnet) to the wall. This bracket will be
used to leave the panel not in direct
contact with the wall and to stabilize it.
3
4
Fixi iron bracket C to the panel
Take the bracket C and fix it with the
screws behind the panel in correspondence
of the holes. Consider which holes to use
based on what the panel will be positioned
(vertical or horizontal).
5
Attaccare il pannello al muro:
take the panel and insert the bracket C in
bracket A in correspondence of the two
cuts. The panel in this way will remain
fixed to the wall.
5
6
The panel is ready to be turned on and
warm up your days.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
