WALLISS ZP-0101 Manual de usuario
Table of contents
Safety warnings
Technical parameter
Packling List
Product description
Charger use
Operation instructions
Adjust chain
Replace chain
Maintenance
Warranty description
Work area security
a) Keep the work area clean and well lit. Cluttered or dark areas can cause accidents.
b) Do not operate power tools in explosive environments, such as in the presence of flammable
liquids, gases, or dust. Power tools can create sparks that may ignite dust or smoke.
c) Keep children and bystanders away when operating power tools. Distractions can cause you
to lose control.
Electrical safety
a) The plug of the power tool must match the socket. Do not modify the plug in any way. Do
not use any adapter plugs with grounded (earthed) power tools. Unmodified plugs and
matching sockets will reduce the risk of electric shock.
b) Avoid body contact with grounded or earthed surfaces, such as pipes, radiators, stoves, and
refrigerators. If your body is grounded or grounded, the risk of electric shock increases.
c) Do not expose power tools to rain or humidity. Water entering power tools increases the risk
of electrocution.
d) Don't abuse the power cord. Never use the power cord for carrying, pulling, or unplugging
power tools. Keep power cords away from heat, oil, sharp edges, or moving parts. Damaged or
tangled wires increase the risk of electric shock.
e) When operating power tools outdoors, use extension cords suitable for outdoor use. Use a
power cord suitable for outdoor use to reduce the risk of electric shock.
f) If you cannot avoid operating power tools in wet areas, use a ground fault circuit breaker
(GFCI) to protect the power. Use of GFCI reduces the risk of electric shock.
Personal safety
a) Be vigilant when operating power tools, observe what you are doing and use common sense.
Do not use power tools when you are tired or under the influence of drugs, alcohol or drugs. A
momentary lapse of concentration while operating power tools can result in serious injury.
b) Use personal protective equipment. Always wear safety goggles. Wearing gloves and using
protective equipment such as a dust mask, non-slip safety shoes, hard hat or hearing protec-
tion under appropriate conditions will reduce personal injury.
c) Prevent accidental startup. Before connecting to a power supply and/or battery pack, pick up
or carry the tool. Carrying a power tool with your finger on a switch or powering a power tool
with the switch on can cause an accident.
d) Remove any adjusting keys or wrenches before turning on power tools. A wrench or key left
on a rotating part of a power tool may result in personal injury.
e) Don't overdo it. Always maintain proper footing and balance. This allows for better control of
power tools in unexpected situations.
f) Dress appropriately. Don't wear loose clothing or jewelry. Keep your hair, clothes, and gloves
away from moving parts. Loose clothing, jewelry, or long hair can get involved in moving parts.
G) If equipment is provided for connecting dust removal and collection facilities, ensure that
such equipment is connected and used properly. The use of dust collectors can reduce dust-re-
lated hazards.
Safety warnings
1
Packling List
Technical parameter
No. Name
1
2
3
4
5
6
Power chain saw
Chain
Guide plate sleeve
Lubricating oil Bottle
Battery
Charger
Quantity
1
2
1
1
2
1
Modle
Battery Voltage
Output speed
Chain saw speed
Bar Length
ZP-0101
20V
5600RPM
10.7m/s
6”
Chain type
3/8
”
2
Product description
Cancel button Check button
Indicating LEDS
Guide Chain
Chain Baffle
High quality chain
Locking knob
Adjusting knob
Manual oil pump
Protection Swtich
Power Switch
Non-Dilp Handle
Lithium Battery
3
Note:
● The batteries produced by our company must be used,
● The battery is fully charged, please unplug the power.
● The battery has temperature protection, low voltage protec-
tion and over current protection. Not found when using normal
power. supply, please check whether the temperature is too high
due to unreasonable use, and need to be cooled before using.
When the voltage is too low, charge in time, and the working
current will also protect.
● It is found that the battery has sparks and smoke and peculiar
smell during work. Please deactivate immediately and contact
the manufacturer.
● Charge the battery, the red light will be on when charging,
the green light will be on when fully charged.
4
Battery Packing:Pay attention to
alingning slots inserts Button press and pull put the
battery pack
Charger use
Must use the charger produced by our company, The charger can
only be used when the battery of the same voltage is inserted
Mentioned in the matter.
● Plug in the power indicator light green, and when the battery is
charging, the indicator light is red, charging the full power indica-
tor is green
● Insert the battery. please push the battery a little harder
to the charger to ensure good contact.
● Please use it at a temperature of 0-40 degrees, the northern
area is cold in winter, please indoor charging.
5
Operation instructions
Adjust chain
Starting device
Second Press the
power switch to start
1.First counterclockwise rotation Locking knob,Re-
lease cover plate
2.Twisted the adjusting knob clockwise to tension the
chain,counterclockwise is for loosening
3.Turn the locking knob clockwise to lock the cover
First Hold on the
Protection Swtich
Note
● After the installation is complete,
start the machine with
no load first and observe the normal
operation of the
machine.
● It is not advisable to cut too hard,
according to the actual
cutting situation, first small and then
large.
6
3. Fit in one end of the saw chain on the top of the guide bar and the other end
around the sprocket.
5. Turn the lever clockwise until the sprocket cover is secured
Replace chain
1. Remove the sprocket cover.
2.Put the chain into the guide plate
4.Installing the guide plate, make sure that the adjusting block gets stuck into
thepositioning adjusting hole at the end of the guide platel
7
Note
● Install the chain
according to the
requirements of the
operation diagram.
Note: Unplug the
battery pack during
installation and
removal of the guide
plate.
To ensure the safety of use,only the original parts can be used.
Repair work functions not mentioned in this specification are performed by
the service center. To ensure safe use, only original parts can be used.
Please close the equipment before starting the chair repair. Clear the connec-
tion between the battery and the plant and store the battery in a safe pack-
age.
Wear hand care when touching safety blades.This can avoid sharp blade
scratching the user. Follow-up cleaning and maintenance must be carried out
regularly. This ensures long-term and reliable operation of the equipment.
Do not spray the equipment with water or break it into the water, otherwise,
it may cause electric shock. Keep the ventilator, motor room and equipment
handle clean. Use a damp cloth or brush cleaner.
Do not use a bay cleaner. Otherwise, it may cause permanent saka failure of
the equipment. Please clean the blade carefully after each use.
Use oily cloth to wipe the blade and absorb the metal to protect the fog.
Aner 8 hours of continuous operation, pleaseremove the debris such as dust
from the front turbulent cover plate of the equipment
Maintenance
8
Tabla de contenidos
