Wacker Neuson Trowel CT 24-4A Manual de usuario
Operator’s Manual
Trowel
CT24-4A
Type CT24-4A
Document 5000184477
Date 0917
Version 12
Language EN
5000184477
Copyright notice
©Copyright 2017by Wacker Neuson Production Americas LLC
All rights, including copying and distribution rights, are reserved.
This publication may be photocopied by the original purchaser of the
machine. Any other type of reproduction is prohibited without express
written permission from Wacker Neuson Production Americas LLC.
Any type of reproduction or distribution not authorized by Wacker
Neuson Production Americas LLC represents an infringement of valid
copyrights. Violators will be prosecuted.
Trademarks
All trademarks referenced in this manual are the property of their
respective owners.
Manufacturer
Wacker Neuson Production Americas LLC
N92W15000 Anthony Avenue
Menomonee Falls, WI 53051 U.S.A.
Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957
www.wackerneuson.com
Original instructions
This Operator’s Manual presents the original instructions. The original
language of this Operator’s Manual is American English.
CT 24-4A Foreword
wc_tx003230gb.fm 3
Foreword
SAVE THESE INSTRUCTIONS—This manual contains important instructions for
the machine models below. These instructions have been written expressly by
Wacker Neuson Production Americas LLC and must be followed during installation,
operation, and maintenance of the machines.
Machine
identification
A nameplate listing the model number, item number, revision number, and serial
number is attached to this machine. The location of the nameplate is shown above.
Serial number
(S/N)
For future reference, record the serial number in the space provided below. You will
need the serial number when requesting parts or service for this machine.
Machine
documentation
From this point forward in this documentation, Wacker Neuson Production
Americas LLC will be referred to as Wacker Neuson.
Keep a copy of the Operator’s Manual with the machine at all times.
Use the separate Parts Book supplied with the machine to order replacement
parts.
If you are missing either of these documents, please contact Wacker Neuson to
order a replacement or visit www.wackerneuson.com.
When ordering parts or requesting service information, be prepared to provide
the machine model number, item number, revision number, and serial number.
Machine Item Number
CT 24-24A 0620105, 0620849
wc_gr010143
Serial Number:
Foreword CT 24-4A
4wc_tx003230gb.fm
Expectations
for
information in
this manual
This manual provides information and procedures to safely operate and
maintain the above Wacker Neuson model(s). For your own safety and to
reduce the risk of injury, carefully read, understand, and observe all instructions
described in this manual.
Wacker Neuson expressly reserves the right to make technical modifications,
even without notice, which improve the performance or safety standards of its
machines.
The information contained in this manual is based on machines manufactured
up until the time of publication. Wacker Neuson reserves the right to change
any portion of this information without notice.
The illustrations, parts, and procedures in this manual refer to Wacker Neuson
factory-installed components. Your machine may vary depending on the
requirements of your specific region.
Manufacturer’s
approval
This manual contains references to approved parts, attachments, and modifica-
tions. The following definitions apply:
Approved parts or attachments are those either manufactured or provided by
Wacker Neuson.
Approved modifications are those performed by an authorized Wacker
Neuson service center according to written instructions published by Wacker
Neuson.
Unapproved parts, attachments, and modifications are those that do not
meet the approved criteria.
Unapproved parts, attachments, or modifications may have the following conse-
quences:
Serious injury hazards to the operator and persons in the work area
Permanent damage to the machine which will not be covered under warranty
Contact your Wacker Neuson dealer immediately if you have questions about
approved or unapproved parts, attachments, or modifications.
CALIFORNIA
Proposition
65 Warning
Combustion exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm.
Laws
pertaining to
spark
arresters
NOTICE: State Health Safety Codes and Public Resources Codes specify that in
certain locations spark arresters be used on internal combustion engines that use
hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-
charge of sparks or flames from the engine exhaust. Spark arresters are qualified
and rated by the United States Forest Service for this purpose. In order to comply
with local laws regarding spark arresters, consult the engine distributor or the local
Health and Safety Administrator.
Original Declaration of Conformity
2016_CE_CT24-4A_en_FM10.fm
EC Declaration of Conformity
Manufacturer
Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,
Menomonee Falls, Wisconsin 53051, USA
Product
Product
Product category
Product function
Item number
CT24-4A
Trowel
To smooth and finish semi-cured concrete
5000620849
Directives and Standards
We hereby declare that this product meets and complies with the relevant regulations and
requirements of the following directives and standards:
2006/42/EC, 2014/30/EU, EN12649
Authorized Person for Technical Documents
Robert Raethsel, Wacker Neuson Produktion GmbH & Co. KG, Wackerstrasse 6, 85084
Reichertshofen, Germany
Menomonee Falls, WI, USA, 24.06.16
Keith Herr
Vice President and Managing Director
For Wacker Neuson
Scott Grahl
Manager, Product Engineering
For Wacker Neuson
Jeff Volden
Director, Product Engineering
For Wacker Neuson
Table of Contents
CT 24-4A
wc_bo5000184477_12TOC.fm 7
Foreword 3
EC Declaration of Conformity 5
1 Safety Information 9
1.1 Signal Words Used in this Manual ....................................................... 9
1.2 Machine Description and Intended Use ............................................. 10
1.3 Safety Guidelines for Operating the Machine ..................................... 11
1.4 Service Safety .................................................................................... 13
1.5 Operator Safety while Using Internal Combustion Engines ............... 15
2 Labels 16
2.1 Label Locations .................................................................................. 16
2.2 Label Meanings .................................................................................. 17
3 Lifting and Transporting 20
3.1 Lifting the Machine ............................................................................. 20
3.2 Transporting the Machine ................................................................... 21
4 Operation 22
4.1 Preparing the Machine for First Use ................................................... 22
4.2 New Machine Set-Up ......................................................................... 22
4.3 Recommended Fuel ........................................................................... 23
4.4 Refueling the Machine ........................................................................ 24
4.5 Installing Blades ................................................................................. 25
4.6 Unfolding Handle ................................................................................ 26
4.7 Controls .............................................................................................. 27
4.8 Operator Present Lever ...................................................................... 27
4.9 Before Starting ................................................................................... 28
4.10 Starting ............................................................................................... 28
4.11 Stopping ............................................................................................. 29
4.12 Position of the Operator ..................................................................... 30
4.13 Operation ............................................................................................ 30
4.14 Emergency Shutdown Procedure ....................................................... 31
4.15 Pitch Adjustment ................................................................................ 32
Table of Contents CT 24-4A
wc_bo5000184477_12TOC.fm
8
5 Maintenance 33
5.1 Maintaining the Emission Control System ...........................................33
5.2 Periodic Maintenance Schedule ..........................................................33
5.3 Engine Oil ............................................................................................34
5.4 Servicing the Air Cleaner .....................................................................35
5.5 Spark Plug ...........................................................................................36
5.6 Cleaning the Sediment Cup ................................................................37
5.7 Adjusting the Idle Speed .....................................................................38
5.8 Carburetor Adjustment ........................................................................39
5.9 Belt Replacement ................................................................................40
5.10 Trowel Lubrication ...............................................................................41
5.11 Storage ................................................................................................42
6 Troubleshooting 43
7 Technical Data 44
7.1 Dimensions and Weights .....................................................................44
7.2 Engine .................................................................................................45
7.3 Trowel ..................................................................................................46
7.4 Sound and Vibration Specifications .....................................................47
8 Emission Control Systems Information and Warranty 48
8.1 Emission Control Systems Warranty Statement .................................48
9 AEM Safety Manual 49
wc_si000741gb.fm 9
CT 24-4A Safety Information
1 Safety Information
1.1 Signal Words Used in this Manual
This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE
signal words which must be followed to reduce the possibility of personal injury,
damage to the equipment, or improper service.
NOTICE: Used without the safety alert symbol, NOTICE indicates a situation
which, if not avoided, could result in property damage.
Note: A Note contains additional information important to a procedure.
This is the safety alert symbol. It is used to alert you to potential personal hazards.
fObey all safety messages that follow this symbol.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
fTo avoid death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
fTo avoid possible death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
fTo avoid possible minor or moderate injury from this type of hazard, obey all
safety messages that follow this signal word.
wc_si000741gb.fm
10
Safety Information CT 24-4A
1.2 Machine Description and Intended Use
This machine is a walk-behind concrete finishing trowel. The Wacker Neuson
Walk-Behind Trowel consists of a frame onto which are mounted a gasoline
engine, a fuel tank, a gearbox, and a control handle. A set of four metal blades is
connected to the gearbox and is surrounded by a ring guard. The engine rotates
the blades through the gearbox and clutch mechanism. The rotating blades ride on
the surface of curing concrete, creating a smooth finish. The operator walks behind
the machine and uses the handle to control speed and direction of the machine.
This machine is intended to be used for floating and burnishing curing concrete.
This machine has been designed and built strictly for the intended use described
above. Using the machine for any other purpose could permanently damage the
machine or seriously injure the operator or other persons in the area. Machine
damage caused by misuse is not covered under warranty.
The following are some examples of misuse:
Using the machine as a ladder, support, or work surface
Using the machine to carry or transport passengers or equipment
Using the machine to finish inappropriate materials such as slurries, sealers, or
epoxy finishes
Operating the machine outside of factory specifications
Operating the machine in a manner inconsistent with all warnings found on the
machine and in the Operator’s Manual
This machine has been designed and built in accordance with the latest global
safety standards. It has been carefully engineered to eliminate hazards as far as
practicable and to increase operator safety through protective guards and labeling.
However, some risks may remain even after protective measures have been taken.
They are called residual risks. On this machine, they may include exposure to:
Heat, noise, exhaust, and carbon monoxide from the engine
Chemical burns from curing concrete
Fire hazards from improper refueling techniques
Fuel and its fumes, fuel spillage from improper lifting technique
Personal injury from improper lifting techniques or operating techniques
Cutting hazards from sharp or worn blades
To protect yourself and others, make sure you thoroughly read and understand the
safety information presented in this manual before operating the machine.
Otros manuales para Trowel CT 24-4A
1
Tabla de contenidos
Otros manuales de Paleta de Wacker Neuson
Wacker Neuson
Wacker Neuson CT 36 Manual de usuario
Wacker Neuson
Wacker Neuson CRT 36-25 Manual de usuario
Wacker Neuson
Wacker Neuson CRT48-35V Manual de usuario
Wacker Neuson
Wacker Neuson CT 36-400E Manual de usuario
Wacker Neuson
Wacker Neuson CRT 48-31V Manual de usuario
Wacker Neuson
Wacker Neuson CRT 48 Manual de usuario
Wacker Neuson
Wacker Neuson CT 36 Instrucciones de funcionamiento
Wacker Neuson
Wacker Neuson CRT 48-31V-ES Manual de usuario
