Von Duprin 9950WDC Manual de usuario

*24739468*

24739468

NOTE: If door does not have a

cutout for cabling inside lock

stile, door must be routed. Refer

to 98/9950WDC wood door

template #24663650.

1-Point

Latch

(LBL)

2-Point

Latch

includes these

additional

components

Fire-Rated

Devices

include these

additional

components

Metal Edge

Wrap required

for 60 and

90-minute

applications

98/9950WDC

Installation Instructions

1 OVERVIEW AND DOOR PREPARATION

TABLE OF CONTENTS

INSTALLATION

Overview and Door Preparation pg 2-3

Fire Barrier pg 4-5

Latch Installation pg 6

Cable Installation pg 7

Device Installation pg 8-9

ADJUSTMENT

Device Adjustment pg 10-11

Strikes and Fire Pin pg 12-13

Bottom Latchbolt Clearance pg 14

Top Strike and Covers pg 15

Troubleshooting pg 16

10.

98/9950WDC

Instead of traditional rods, concealed vertical cables are utilized, making use of a proven technology

that enables quick installation and allows for easy maintenance. Simplified sizing, ease of adjustment

and greater door integrity make the Wood Door Concealed exit device a more secure solution, without

the complexity associated with traditional concealed systems. Another key benefit of the system is the

ability to make adjustments to the system by simply removing the scalp plate from the edge of the

door.

If you have any questions or comments please visit the resources below or give us a call so we can

help get you on your way. Thank you for your continued support of Von Duprin.

Technical Support hot line: 877-671-7011

Scan this QR code or visit us online at kc.allegion.com to access the

Allegion Knowledge Center.

Need a reader for your phone?

For iPhone: QR Reader

For Android: QR Barcode Scanner

1 (continued)

1a For 60 and 90-minute applications, install metal edge

wrap.

1b If necessary, prepare door for top strike cutout.

⁵⁄₈"

Cut out material

this side only

Latch

Push side of door, RHR shown

1³⁄₁₆"

1c With door laying at, draw horizontal device center

line (C

L).

RHR shown

(LHR opposite)

NOTE: Centerline is

predetermined by cutout.

1d If necessary, align plastic template to mark 4 holes.

Plastic

Template

1e Prepare center case mounting holes as required.

Sex Bolts or 990 Trims

¹³⁄₃₂"

Trim side

⁵⁄₁₆"

Device side

Surface Mount

¹⁄₈" Drill

Pilot 1¹⁄₂" Deep

1f Prepare center slide mounting hole.

Ø ³⁄₈"

Push side

only

1⁷⁄₈"

Push side of door, RHR shown

(LHR opposite)

Device

2 FIRE BARRIER

Fire application only

 Firecomponentsmustbeinstalledtomaintainreratingofopening.

2a Peel adhesive backing from intumescent and apply to trim side of re barrier.

 Intumescentmustbeproperlyalignedbeforeexposedadhesivecontactsrebarrier.Adhesiveispermanentandnot

repositionable.

Trim Side Trim Side

RHR LHR

a-1 a-1

a-2 a-2

2b Remove appropriate knockouts for device and trim.

RHR LHR

Exit Only (EO) shown Exit Only (EO) shown

2c With re barrier in correct orientation, slide barrier into door pocket. Secure re barrier to inside of pocket with 2

screws.

Trim Side

c-1

c-2

RHR shown

2 (continued)

Trim

Model

Exit Only

990

996

990

996

VR910

VR914

AD-993

CO-993

696

697

392-7

696

697

696

697

110

110WD

IVES 8190

Trim

Function

L-NL

K-NL

TP-BE

L-BE

L-DT

K-BE

K-DT

TP-BE

NL-MD

NL-OP

Right Hand Reverse (RHR)

Remove the knockouts listed below

A B C D E J K

A B C D E H I J K

A B C D E H I J K L

A B C D E K

A B C D E H I K

A B C D E F H I K

A B C D E H I K

Drill thru barrier

Left Hand Reverse (LHR)

Remove the knockouts listed below

D E G H I J K

B C D E G H I J K

B C D E F G H I J K

E G H I J K

B C E G H I J K

B C E G H I J K L

B C E G H I J K

Drill thru barrier

FIRE BARRIER KNOCKOUT TABLE

RHR LHR

3 LATCH INSTALLATION

3a Conrm top latch is marked for EXIT DEVICES ONLY,

then remove label.

ATTENTION:

FOR USE WITH

EXIT DEVICES ONLY

3b Connect cable end tting(s) to latch(es).

 For2-pointlatches,thetopcableisthelongerofthetwo

cables.Topcableissilver,bottomcableisblack.

Top Bottom

For 2-Point

Latch Only

Pull down on

cable link

Slide cable end

into cable link

b-2

b-1

Bend cable slightly

to access

cable link,

then

install

cable

link

cable

link

3c Slide latch(es) into door pocket.

 Clearcablechannelofdebrisrstifnecessary.

Push Side

of Door

Push Side

of Door

Bottom

For 2-Point

Latch Only

Top

Push

Side

Push

Side

3d Secure latch(es).

RHR shown

Push Side

of Door

Push Side

of Door

BottomTop

For 2-Point Latch Only

#25 Drill, Pilot 1¹⁄₂" Deep x4

#10 x 1¹⁄₂"

#25 Drill, Pilot 1¹⁄₂" Deep x4

If using metal edge

wrap, mount latches

using this screw

3e Perform cable binding check at mortise pocket.

TOP

Pulling on top cable should

lock and unlock top latch.

(2-pt only) Pulling on

bottom cable should

retract bottom latch.

3f Prepare door for hanging.

Pull bottom cable taut enough so bottom bolt will not

drag against floor, and tape cable end to door edge

(f-2). This holds cable in place, preventing it from

dropping into door channel. Tape bottom bolt in place

(f-3).

Pull top cable taut and tape cable

end to door edge (f-1).

f-3

f-2

f-1

For 2-Point

Latch Only

3g Hang door on frame.

 For2-pointlatches,bottomlatchcannotbeinlocked

positionwhilehangingdooronframe.Latchmustbe

retracted.

4 CABLE INSTALLATION

4a Insert cable end tting(s) into center slide.

 Besuretoattachtopcabletotopendofcenterslide

(marked“ThisSideUp”)

a-4

a-5

⁵⁄₃₂"

hex

wrench

a-2 a-3

Remove tape from door edge, then repeat

process to install bottom cable into bottom spool.

For 2-Point Latch Only

a-6

a-1

Pull top cable thru mortise

opening (a-1).

Rotate spool using hex

wrench to reveal cable hole

in spool (a-2), if it is not

visible or only partially

visible.

Insert cable end into spool

(a-3).

Turn spool screw clockwise

(a-4) to rotate spool until

cable end is beneath profile

of center slide (a-5).

Marked "This Side Up"

4b Take up top cable slack only.

⁵⁄₃₂"

hex wrench

Position center slide as shown. Turn top

spool screw clockwise to tighten (b-1)

until center slide is no longer hanging

outside door.

NOTE: If clicking noises are heard

during clockwise adjustment, unwind

the cable with one-half turn counter-

clockwise. Then, continue clockwise

adjustment. If clicking persists, check to

be sure cable is not caught on an edge.

Center slide

is resting on

step of door

pocket

b-1

Do not adjust

bottom cable

at this time.

4c Secure center slide.

¹⁄₈" Drill, Pilot 1" Deep x2

#8 x 1"

4d Adjust top spool.

Turn top spool screw (d-2) until pin is

centered to the line (d-3).

Put top latch in locked

position (d-1).

NOTE: Top latch must be placed

in locked position prior to making

top adjustment.

Released Locked

NOTE: No further top spool adjustment needed.

Put hex wrench away until Step 8b.

Confirm top latch is

still locked (d-4).

Locked

d-1

d-4

d-2

pin d-3

If latch won’t lock,

top spool screw

was overtightened

in Step 4b and

needs to be

backed out

counter-clockwise.

5 DEVICE INSTALLATION

5a If necessary, cut device.

Cover Plate

Flush

Door

1¹⁄₂" (38 mm)

Recommended

Jamb

Temporarily Remove

Anti-Rattle Clip

5b If necessary, remove NL drive screw.

With the NL drive screw removed, key locks and unlocks lever, knob, or

thumb piece. For the trims listed below,

REMOVE NL drive screw.

996L 696TP 990TP

996K 697TP

With the NL drive screw installed, key retracts latch bolt.

DO NOT remove

NL drive screw for the following applications:

NL, EO, DT trims and 98/99-2 double cylinder devices (i.e. TP-2,

L-2, and K-2).

If the trim being installed is "BE" (i.e. 996L-BE), the trim lock tumbler

on the back of the device must be in the

UP position before device

is installed. This allows the trim to be unlocked at all times.

*996L-BE

*996K-BE

*E996L

*E996L-BE

*696TP-BE

*697TP-BE

*990TP-BE

NL drive screw

Factory installed on

back of center case

Correct

Orientation

(RHR shown)

Incorrect

Orientation

trim lock

tumbler in

UP position

If necessary,

remove drive

screw and

rotate cam

until trim lock

tumbler is in

UP position,

then reinstall

drive screw

360˚

5c Install lift nger(s) and retainer clip(s).

With device center case hanging over

edge of table, slide L-shaped lift finger

thru upper block of center case.

Insert lift finger screw and turn

clockwise with screwdriver to

raise lift finger until the slot aligns

with diameter of screw hole.

Lightly tighten locking screw (c-4)

Install retainer clip against lift finger,

snapping it into the slot of the lift

finger screw.

For 2-Point Latch Only

Repeat steps c-1 thru c-5 for lower block of center case.

Confirm lift finger screw is

free to rotate (c-5).

It may be necessary to rotate

the lift finger screw to realign

retainer clip and lift finger holes.

Top

c-1

c-6

c-2

slot

c-3

c-5

c-4

Bottom

5 (continued)

5d Attach center case to door.

Surface Mount Sex Bolts

Thru-bolting Trim

(1³⁄₄" door)

(2¹⁄₄" door)

(1³⁄₄" door)

(2¹⁄₄" door)

!Do not overtighten center case to door (door edge cover plate won’t fit).

5e Mark and prepare 2 holes.

Surface Mount

¹⁄₈" Drill, Pilot 1" Deep

Sex Bolts

¹³⁄₃₂" Drill thru

e-1 e-2

e-3

5f Install end cap bracket and end cap.

#10 x 1¹⁄₄" Wood screw

(Surface mount WDC)

#10-24 x ³⁄₄"

(Sex bolts, 1³⁄₄" door)

#10-24 x 1¹⁄₈"

(Sex bolts, 2¹⁄₄" door)

f-1 f-2

5g Secure center slide to face of door.

8-32 x 1"

6 DEVICEADJUSTMENT

ADJUSTMENT COMPONENTS

Push Side of Door

Center Case

Push Side / Edge of Door

Center Slide

For 2-point

latch only

Top lift finger screw:

Adjusts release point of latches

Bottom lift finger screw*:

Adjusts release point of latches

Top locking screw:

Locks lift finger screw adjustment

Bottom locking screw*:

Locks lift finger screw adjustment

Top spool screw:

Sizes cable to door height

and undercut

Bottom spool screw*:

Sizes cable to door height

and undercut

Bottom latch pin*

(reference for adjustment)

Bottom lift finger*:

Transfers motion from exit

device spool inputs

Top lift finger:

Transfers motion from exit

device spool inputs

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de apertura de puertas de Von Duprin

Von Duprin

Von Duprin 33/3527A Manual de usuario

Von Duprin

Von Duprin 35A-F Manual de usuario

Von Duprin

Von Duprin QEL94/9547 Series Manual de usuario

Von Duprin

Von Duprin 9849WDC Manual de usuario

Von Duprin

Von Duprin 33/35A Manual de usuario

Von Duprin

Von Duprin 2227-F Manual de usuario

Von Duprin

Von Duprin Chexit CX33A/35A Manual de usuario

Von Duprin

Von Duprin 98/9927 Manual de usuario

Von Duprin

Von Duprin 3550AWDC Manual de usuario

Von Duprin

Von Duprin WS9927 Manual de usuario

Von Duprin

Von Duprin WS9857-F Manual de usuario

Von Duprin

Von Duprin 98 Manual de usuario

Von Duprin

Von Duprin Allegion 3327A Series Manual de usuario

Von Duprin

Von Duprin 98/9949 Manual de usuario

Von Duprin

Von Duprin 98/9975 Series Manual de usuario

Von Duprin

Von Duprin Quiet One 9847WDC Manual de usuario

Von Duprin

Von Duprin 33A Series Manual de usuario

Von Duprin

Von Duprin 33A Series Manual de usuario

Von Duprin

Von Duprin XP98 Manual de usuario

Manuales populares de Sistema de apertura de puertas de otras marcas

Pamex

Pamex KT-INP35 Manual de usuario

Label

Label NEPTIS/LE Manual de usuario

Cal-Royal

Cal-Royal N-F77CVR Manual de usuario

Scrigno

Scrigno OPEN1000 Manual de usuario

TriMark

TriMark UM 34 Manual de usuario

BFT

BFT WIND RMB 130B 200 Manual de usuario

Alecto

Alecto ADI-250 Manual de usuario

Besam

Besam Swingmaster MP Guía

CRL

CRL SENIOR PRIMA Manual de usuario

Assa Abloy

Assa Abloy SARGENT 1431 Series Manual de usuario

GAL

GAL MOVFR Hoja de especificaciones

Olide

Olide 120B Manual de usuario

Normstahl

Normstahl IDO7 Manual de usuario

Häfele

Häfele Finetta T 70 VF Manual de usuario

AGS

AGS D-PL Manual

Stanley

Stanley MA900ñ Instrucciones de instalación

WITTUR

WITTUR Hydra Plus UD300 Manual

Alutech

Alutech TR-3019-230E-ICU Instrucciones de instalación y funcionamiento