VOLTCRAFT DSO-2154 Manual de usuario

DSO-2154 Oscilloscope

Quick Guide

Table of Contents

1. General Safety Requirements.......................................................................................... 1

2. Safety Terms and Symbols................................................................................................2

3. Quick Start........................................................................................................................4

Introduction to the Structure of the Oscilloscope............................................................ 4

Front Panel..............................................................................................................................................4

Rear Panel...............................................................................................................................................5

Control Area........................................................................................................................................... 6

User Interface Introduction..................................................................................................... 7

How to Implement the General Inspection..........................................................................9

How to Implement the Function Inspection........................................................................9

How to Implement the Probe Compensation................................................................... 10

How to Set the Probe Attenuation Coefficient.................................................................11

How to Use the Probe Safely................................................................................................ 12

How to Implement Self-calibration......................................................................................13

Introduction to the Vertical System.................................................................................... 13

Introduction to the Horizontal System...............................................................................14

Introduction to the Trigger System.....................................................................................15

How to Measure Automatically.................................................................................................16

4. Communication with PC................................................................................................ 17

5. Appendix......................................................................................................................... 18

Appendix A: Enclosure.............................................................................................................. 18

Appendix B: General Care and Cleaning.................................................................................18

1.General Safety Requirements

1. General Safety Requirements

Before use, please read the following safety precautions to avoid any

possible bodily injury and to prevent this product or any other connected

products from damage. In order to avoid any contingent danger, ensure this

product is only used within the range specified.

Only the qualified technicians can implement the maintenance.

To avoid Fire or Personal Injury:

Connect the probe correctly. The grounding end of the probe

corresponds to the grounding phase. Please don't connect the

grounding end to the positive phase.

Use Proper Power Cord. Use only the power cord supplied with the product

and certified to use in your country.

Connect or Disconnect Correctly. When the probe or test lead is connected

to a voltage source, please do not connect and disconnect the probe or test

lead at random.

Product Grounded. This instrument is grounded through the power cord

grounding conductor. To avoid electric shock, the grounding conductor must be

grounded. The product must be grounded properly before any connection with

its input or output terminal.

When powered by AC power, it is not allowed to measure AC power

source directly, because the testing ground and power cord ground

conductor are connected together, otherwise, it will cause short circuit.

Check all Terminal Ratings. To avoid fire or shock hazard, check all ratings

and markers of this product. Refer to the user's manual for more information

about ratings before connecting to the instrument.

Do not operate without covers. Do not operate the instrument with covers or

panels removed.

Use Proper Fuse. Use only the specified type and rating fuse for this

instrument.

Avoid exposed circuit. Do not touch exposed junctions and components

when the instrument is powered.

Do not operate if in any doubt. If you suspect damage occurs to the

instrument, have it inspected by qualified service personnel before further

operations.

Use your Oscilloscope in a well-ventilated area. Make sure the instrument

installed with proper ventilation, refer to the user manual for more details.

Do not operate in wet conditions.

Do not operate in an explosive atmosphere.

Keep product surfaces clean and dry.

2.Safety Terms and Symbols

2. Safety Terms and Symbols

Safety Terms

Terms in this manual. The following terms may appear in this manual:

Warning: Warning indicates the conditions or practices that could result

in injury or loss of life.

Caution: Caution indicates the conditions or practices that could result in

damage to this product or other property.

Terms on the product. The following terms may appear on this product:

Danger: It indicates an injury or hazard may immediately happen.

Warning: It indicates an injury or hazard may be accessible potentially.

Caution: It indicates a potential damage to the instrument or other property might

occur.

Safety Symbols

Symbols on the product. The following symbol may appear on the product:

Hazardous Voltage

Refer to Manual

Protective Earth Terminal

Chassis Ground

Test Ground

2.Safety Terms and Symbols

To avoid body damage and prevent product and connected equipment damage,

carefully read the following safety information before using the test tool. This

product can only be used in the specified applications.

Warning:

The four channels of the oscilloscope are not electrically isolated. The

channels should adopt a common ground during measuring. To prevent

short circuits, the 2 probe grounds must not be connected to 2 different

non-isolated DC levels.

The diagram of the oscilloscope ground wire connection:

It is not allowed to measure AC power when the AC powered oscilloscope is

connected to the AC-powered PC through the ports.

Warning:

To avoid fire or electrical shock, when the oscilloscope input

signal connected is more than 42V peak (30Vrms) or on circuits of

more than 4800VA, please take note of below items:

Only use accessory insulated voltage probes and test lead.

Check the accessories such as probe before use and

replace it if there are any damages.

Remove probes, test leads and other accessories

immediately after use.

Remove USB cable which connects oscilloscope and

computer.

Do not apply input voltages above the rating of the

instrument because the probe tip voltage will directly

transmit to the oscilloscope. Use with caution when the

probe is set as 1:1.

Do not use exposed metal BNC or banana plug connectors.

Do not insert metal objects into connectors.

3.Quick Start

3. Quick Start

Introduction to the Structure of the Oscilloscope

This chapter makes a simple description of the operation and function of the front

panel of the oscilloscope, enabling you to be familiar with the use of the

oscilloscope in the shortest time.

Front Panel

The front panel has knobs and function buttons. The 5 buttons in the column on

the right side of the display screen are menu selection buttons, through which, you

can set the different options for the current menu. The other buttons are function

buttons, through which, you can enter different function menus or obtain a specific

function application directly.

Figure 3- 1 Front panel

1. Display area

2. Menu selection buttons: Select the right menu item.

3. Control (button and knob) area

4. Probe Compensation: Measurement signal (5V/1kHz) output.

5. Signal Input Channel

6. USB Host port: It is used to transfer data when external USB equipment

connects to the oscilloscope regarded as "host device". For example: Saving

the waveform to USB flash disk needs to use this port.

7. Power on/off

3.Quick Start

Rear Panel

Figure 3- 2 Rear Panel

1. Handle

2. Air vents

3. AC power input jack

4. Foot stool: Adjust the tilt angle of the oscilloscope.

5. USB Device port: It is used to transfer data when external USB equipment

connects to the oscilloscope regarded as "slave device". For example: to use

this port when connect PC to the oscilloscope by USB.

3.Quick Start

Control Area

Figure 3- 3 Control Area Overview

1. Function button area: Total 6 buttons.

2. Horizontal control area with 1 button and 2 knobs.

"HOR" button refer to horizontal system setting menu, "Horizontal Position"

knob control trigger position, " Horizontal Scale" control time base.

3. Trigger control area with 2 buttons and 1 knob.

The Trigger Level knob is to adjust trigger voltage. Other 2 buttons refer to

trigger system setting.

4. Copy button: This button is the shortcut for Save function in the Utility function

menu. Pressing this button is equal to the Save option in the Save menu. The

waveform, configure or the display screen could be saved according to the

chosen type in the Save menu.

5. Vertical control area with 5 buttons and 2 knobs.

CH1 -CH4 buttons correspond to setting menu in CH1 - CH4. "Math" button

provides access to math waveform functions (+, -, ×, /, FFT). The "Vertical

Position" knob control the vertical position of current channel, and the

3.Quick Start

"Vertical Scale" knob control voltage scale of current channel.

6. Mknob(Multipurpose knob): when a symbol appears in the menu, it

indicates you can turn the Mknob to select the menu or set the value. You can

push it to close the menu on the left and right.

User Interface Introduction

Figure 3- 4 Illustrative Drawing of Display Interfaces

1. Waveform Display Area.

2. Run/Stop

3. The state of trigger, including:

Auto: Automatic mode and acquire waveform without triggering.

Trig: Trigger detected and acquire waveform.

Ready: Pre-triggered data captured and ready for a trigger.

Scan: Capture and display the waveform continuously.

Stop: Data acquisition stopped.

4. The two blue dotted lines indicates the vertical position of cursor

measurement.

5. The T pointer indicates the horizontal position for the trigger.

6. The pointer indicates the trigger position in the record length.

7. It shows present triggering value and displays the site of present window in

internal memory.

8. It indicates that there is a USB disk connecting with the oscilloscope.

9. Channel identifier of current menu.

3.Quick Start

10. The waveform of CH1.

11. Right Menu.

12. The waveform of CH4

13. The waveform of CH3

14. The waveform of CH2.

15. Current trigger type:

Rising edge triggering

Falling edge triggering

Video line synchronous triggering

Video field synchronous triggering

The reading shows the trigger level value of the corresponding channel.

16. It indicates the measured type and value of the corresponding channel. "T"

means period, "F" means frequency, "V" means the average value, "Vp"

the peak-peak value, "Vr" the root-mean-square value, "Ma" the maximum

amplitude value, "Mi" the minimum amplitude value, "Vt" the Voltage value

of the waveform's flat top value, "Vb" the Voltage value of the waveform's

flat base, "Va" the amplitude value, "Os" the overshoot value, "Ps" the

Preshoot value, "RT" the rise time value, "FT" the fall time value, "PW" the

+width value, "NW" the -Width value, "+D" the +Duty value, "-D" the -Duty

value, "FRR" the FRR, "FRF" the FRF, "FFR" the FFR, "FFF" the FFF,

"LRR" the, "LRF" the LRF, "LFR" the LFR, "LFF" the LFF,"PD" the Delay

A->B value, "ND" the Delay A->B value, "TR" the Cycle RMS, "CR"

the Cursor RMS, "WP" the Screen Duty, "RP" the Phase, "+PC" the +Pulse

count, "-PC" the - Pulse count, "+E" the Rise edge count, "-E" the Fall

edge count, "AR" the Area, "CA" the Cycle area.

17. The readings show the record length.

18. The frequency of the trigger signal.

19. The readings show current sample rate.

20. The readings indicate the corresponding Voltage Division and the Zero

Point positions of the channels. "BW" indicates bandwidth limit.

The icon shows the coupling mode of the channel.

"—" indicates direct current coupling

"～" indicates AC coupling

"" indicates GND coupling

21. The reading shows the setting of main time base.

22. It is cursor measure window, showing the absolute values and the

readings of the cursors.

23. The blue pointer shows the grounding datum point (zero point position) of

the waveform of the CH2 channel. If the pointer is not displayed, it means

that this channel is not opened.

24. The orange pointer shows the grounding datum point (zero point position)

Otros manuales para DSO-2154

Tabla de contenidos

Otros manuales de Equipo de prueba de VOLTCRAFT

VOLTCRAFT

VOLTCRAFT DSO-6084F Manual de usuario

VOLTCRAFT

VOLTCRAFT IRS-350 Blackbody Manual de usuario

VOLTCRAFT

VOLTCRAFT VC-55 LCD Manual de usuario

VOLTCRAFT

VOLTCRAFT VC35 Manual de usuario

VOLTCRAFT

VOLTCRAFT FIT-100 RCD Manual de usuario

VOLTCRAFT

VOLTCRAFT VC-55 LCD SE Manual de usuario

VOLTCRAFT

VOLTCRAFT MS-410 Manual de usuario

VOLTCRAFT

VOLTCRAFT BT-501 Manual de usuario

VOLTCRAFT

VOLTCRAFT VDO-2052 Manual de usuario

VOLTCRAFT

VOLTCRAFT DSO-6102 WIFI Manual de usuario

VOLTCRAFT

VOLTCRAFT MS-540 Manual de usuario

VOLTCRAFT

VOLTCRAFT MS-444 Manual de usuario

VOLTCRAFT

VOLTCRAFT DSO-3062C Guía de inicio rápido

VOLTCRAFT

VOLTCRAFT BS-600SD Manual de usuario

VOLTCRAFT

VOLTCRAFT DSO-111 Manual de usuario

VOLTCRAFT

VOLTCRAFT BS-200XW Manual de usuario

VOLTCRAFT

VOLTCRAFT ET-100 Manual de usuario

VOLTCRAFT

VOLTCRAFT DSO-6202 Manual de usuario

VOLTCRAFT

VOLTCRAFT MS-258 II Manual de usuario

VOLTCRAFT

VOLTCRAFT DSO-2072H Manual de usuario

VOLTCRAFT

VOLTCRAFT VC-BT100 Manual de usuario

VOLTCRAFT

VOLTCRAFT MS-248 Manual de usuario

VOLTCRAFT

VOLTCRAFT RT-100 Manual de usuario

VOLTCRAFT

VOLTCRAFT I-V Curve Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario