Vivreau Extra I-Tap Manual de usuario
Extra I-Tap
Installation Guide
Step 1 — Unpack the device and inspect the parts
• To unpack the device, pull the packaging upwards.
• Check for completeness of the installation kit and accessories.
Which are in the upper part of the box.
Step 2 — Examination installation environment
• Check the installation site. Are the pre-requirements available? 1/2” water supply female
threaded, power outlet, countertop hole and CO2
Step 3 —Insert drip tray
• Apply clear silicon to the bottom edge of the drip tray.
• Insert drip tray with drain hose (image 1) and press on.
• Remove excess sealant.
• Bend the fastening tabs on the underside of the drip tray.
Step 4 — Fasten the tap
• Insert the tap with hoses and data cable into the borehole (image 1).
• Screw the threaded sleeve into the tap until it protrudes at least 4 cm from the worktop.
• First slide on the triangular pressure plate and then the washer from below. Then screw on the
fastening nut and hand-tighten.
• Align the tap so that the outlet is centered over the drip tray.
• Tighten the fastening nut and secure with the 3 screws.
Step 5 — Guide the data cable through the ferrite ring
• Guide the data cable through the ferrite ring
and wrap it around the ferrite ring a total of 2
times.
• The ferrite ring should be positioned as high
as possible in front of the threaded sleeve of
the tap.
Step 6 — Water connection concept
• Make the connections at the customer water supply, water block and lter head.
Step 7 — Connection concept
• The water connection concept must already be implemented as described above.
• Important: : When attaching the lter head, there should be enough distance from the lter head to
the worktop so that the head of the lter can be changed if necessary.
• Please note: The CO2 pressure reducer must be set to 65-70psi
• Note: The power cable is provided with a pull-o protection (required for approval reasons). To
remove the cable, the red pin must be pulled.
• In the present example, the water pressure regulator is integrated in the base cabinet as a space-
saving concept. (see second photo)
• The next step is to pull the insulation onto the water hose, which is attached directly before and after
the lter. The cap on the hose prevents dirt from getting into the device.
• Attach the CO2 strap to secure the CO2 bottle in the base cabinet.
• Check whether the water is draining correctly from the drip tray.
Open / close the I-Tap housing Instructions*
• Switch o the device using the power switch.
• First disconnect the power plug from the socket
and then from the device.
• To do this, push the red snap-in hooks (pull-out
protection) to the rear.
Step 1— Establish a stress-free state
• Open the housing (instructions below)*
• Check the device for possible leaks.
Step 8— Remove sidewalls
• The left side wall can be dismantled individually. The right side wall is a component together with the
upper part of the housing.
• For most activities it is sucient to dismantle the left side wall.
• Remove left side wall: remove 2 screws on the front left (Fig. 1) and 2 screws on the side (Fig. 2).
• Remove right side wall / upper part: remove 2 screws at the front right (picture 1) and 2 screws at the
rear.
• The 4 screws on the cover do not have to be removed completely. It is enough to loosen them
(image 3).
• Remove the housing part.
Step 2 — Remove sidewalls
• The housing is closed in reverse order.
• If all housing parts have been removed, the upper part / right side should be installed rst and then
the left housing part.
Step 3 — Close the housing
• Loosen 4 screws . Carefully loosen the last screw
and hold the HMI housing tight. Then loosen the
connector of the HMI and remove the HMI with the
housing.
Step 4 — Disassembly of the HMI housing
• Loosen 4 screws.
• When installing , make sure that the hood is
pushed all the way down. There should be no
gap between the scoop and the oor of the
base unit.
Step 5 — Dismantling the hood
Step 9 — For devices with the Hygiene Plus option
• The SX3 hygiene lter is enclosed separately
on delivery. The point at which this is later
used is bridged with a piece of hose. The
SX3 lter is only used in the course of the
cleaning program (step 8)!
• On delivery, both connections of the lter are
closed with plugs. If these are missing, the
lter must not be used. The caps must be
removed before installation.
Step 10 — Chemical cleaning
• For better accessibility, it is recommended to position the cooler as far forward as possible.
• When connecting the hoses, angle connectors should preferably be used.
• IMPORTANT: The hose from the cooler to the tap should be shortened as much as possible.
• Connect the water, CO 2 and voltage supply lines to the cooler.
• To connect the RJ45 connector, the sheet metal cover must rst be removed. This serves as a splash
guard and must be reinstalled . Firmly insert the plug and carefully mount the cover. If the connection
is poor, the error E326 is output.
• The RJ45 plugs are plugged in as follows: The tap cable into the right socket of the cooler (labeled
Tap) Accessories (waste water container, EAP) are plugged into the left socket of the cooler.
Step 12 — Chemical cleaning
• Carry out cleaning via the menu. Instructions outlined in the next 6 pages.
• During the exposure time, the drip tray can be removed and cleaned.
• In the course of rinsing after cleaning, the water ow can already be measured and adjusted using
the compensators (see next step).
• When rinsing, water is dispensed for 30 seconds; multiply this amount by a factor of 2.
Step 11 — Adjust the tap spout
• Adjust the spout of the tap so that the water jet runs vertically down to the center of the drip tray.
• Use a suitable and disinfected tool for this.
Tabla de contenidos
Otros manuales de Sistema de filtración de agua de Vivreau
