Vivo Mount-E-FD55 Manual de usuario
Electric Flip Down Ceiling TV Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-e-fd55
SKU: MOUNT-E-FD55
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
PACKAGE CONTENTS
WARNING!
A (x1)
Mount
B(x1)
VESA Plate
C(x1)
Ceiling
Template
M-F (x4)
D5 Washer
M-G x4)
D8 Washer
M-H (x8)
Small
Spacer
W-A (x6)
Bolt
M-E (x4)
M8x50
M-A (x4)
M5x14
M-B (x4)
M6x14
M-C (x4)
M6x30
M-D (x4)
M8x30
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
W-C (x4)
Washer
W-B (x6)
Anchor
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us.
D(x2)
Decorative Cover
E(x2)
VESA Adapter
F (x2)
VESA Adapter
G(x1)
Power Adapter
H(x1)
Remote
Control
I(x4)
Cable Tie
M-I (x8)
Big
Spacer
66lbs
(29.94g)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
TOOLS NEEDED
Phillips
Screwdriver
Drill Pencil
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
3
ASSEMBLY STEPS
STEP 1
OPTION A: Wood Ceiling
Using ceiling template (C), mark exact location of
mounting holes. Drill pilot holes 2.2” deep using
a 4.5mm drill bit. Insert two screws (W-A), leaving
a 5mm gap from ceiling. Hang the ceiling mount
so that the screws fit into the keyhole openings.
Slide mount forward, then secure using additional
screws (W-A) with washers (W-C). Tighten all
screws.
OPTION B: Concrete Ceiling
Using ceiling template (C), mark exact location of
mounting holes. Drill pilot holes 2.4” deep, using a
10mm drill bit. Insert six concrete anchors (W-B),
then tighten two screws (W-A), leaving a 5mm gap
from ceiling. Hang the ceiling mount so that the
screws fit into the keyhole openings. Slide mount
forward, then secure using additional screws
(W-A) with washers (W-C). Tighten all screws.
NOTE: If mounting to a wood beam ceiling,
ensure the front and back holes are used for
the main support if mount is in line with the
beam. If perpendicular to the beam, use keyhole
openings for the main support. Do NOT use
included concrete anchors (W-B) for wood or
drywall.
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
4
STEP 2
Remove the two bottom screws from the VESA
plate (B) and set aside for later use.
OPTIONAL (if mounting a TV with a VESA pattern larger than 200mm x 200mm)
Remove the screws from the VESA adapters (E, F). Align the VESA adapters with the VESA plate and
assemble, using screws previously removed from the VESA adapters.
STEP 2 (Continued)
OPTION A: Flat Back TV
Align the VESA plate with the mounting holes in the back of the TV screen. Install VESA plate to TV
using appropriate screws and washers according to your screen type.
5
STEP 2 (Continued)
OPTION B: Curved/Recessed Back TV
Align the VESA plate with the mounting holes in the back of the TV screen. Install VESA plate to TV
using appropriate screws and washers according to your screen type.
STEP 3
Place the VESA plate on the ceiling mount (A) by inserting the attached screw on the VESA plate into
the ceiling mount (A) keyhole .
6
STEP 3 (Continued)
Using screws previously removed (in beginning of step 2), fasten the VESA plate to ceiling mount.
Clearance between the ceiling and top edge of TV should be no less than 15mm when TV is in the fully
lowered position.
7
STEP 4
Run cables along edge of mount. Allow slack in
cables for arm movement. Place covers over cables
and snap into place. Using cable ties (I), fasten
cables.
NOTE: Keep cables clear from arm to avoid damage
due to pinching.
STEP 5
Plug power adapter (G) into mount, and connect to AC outlet.
NOTE: Plugging power supply into AC outlet prior to the mount may cause a large spark when
connecting to the mount.
LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
Otros manuales para Mount-E-FD55
4
Tabla de contenidos
Otros manuales de Soporte de TV de Vivo
Vivo
Vivo STAND V006 Manual de usuario
Vivo
Vivo STAND-TV07A Manual de usuario
Vivo
Vivo STAND-TV70B Manual de usuario
Vivo
Vivo STAND-V002T/W Manual de usuario
Vivo
Vivo STAND-TV00Y Manual de usuario
Vivo
Vivo STAND-TV65F Manual de usuario
Vivo
Vivo MOUNT-POLE01W Manual de usuario
Vivo
Vivo VESA STAND-VAD1B Manual de usuario
Vivo
Vivo MOUNT-SFTV4 Manual de usuario
Vivo
Vivo MOUNT-VW02A Manual de usuario
Vivo
Vivo STAND-V001S Manual de usuario
Vivo
Vivo MOUNT-E-UP65A/AW Manual de usuario
Vivo
Vivo STAND-TV03E Manual de usuario
Vivo
Vivo MOUNT-VW03G Manual de usuario
Vivo
Vivo STAND-TV120B Manual de usuario
Vivo
Vivo MOUNT-VW01E Manual de usuario
Vivo
Vivo MOUNT-WCB01 Manual de usuario
Vivo
Vivo STAND-RACE1TV Manual de usuario
Vivo
Vivo STAND-V002DU Manual de usuario
Vivo
Vivo MOUNT-VW11 Manual de usuario
