Vivo STAND-SIT1W Manual de usuario
Sit to Stand Single Monitor Wall Mount Workstation -
Silver
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-sit1w
SKU: STAND-SIT1W
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
PACKAGE CONTENTS
4.4 - 17.6lbs
(2 -8 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us.
A (x1)
Arm
B(x1)
Pole
C(x1)
Tray
D(x2)
Decorative
Cover
E(x2)
M8x24
F (x1)
4mm Allen
Wrench
G(x1)
6mm Allen
Wrench
H (x1)
Mount
I (x2)
Straps
M-A (x4)
M4x12
M-C (x4)
M4x16
M-B (x4)
M5x12
M-D (x4)
M5x16
M-F (x4)
Spacer
M-E (x4)
D5 Washer
W-A (x7)
Screw
W-C (x3)
Washer
W-B (x7)
Anchor
3
ASSEMBLY STEPS
OPTION A: Wood Stud Mounting
Hold arm (A) to wall where stud is located and mark top
hole location with a pencil. Drill 2.2” (55mm) deep hole
using a 3/16” (4.5mm) drill bit, and insert screw (W-A)
leaving 6mm of thread exposed. Hang arm on screw,
and making sure arm is level, mark 2 additional drilling
locations using the vertically aligned holes. Drill holes,
then mount arm using screws (W-A) with washers (W-C).
STEP 1
OPTION B: Concrete/Brick Mounting
Hold arm (A) to wall where desired and
mark top hole location with a pencil.
Drill 2.4” (60mm) deep hole using a 3/8”
(10mm) drill bit, and insert anchor (W-B).
Insert screw (W-A) leaving 6mm of thread
exposed. Hang arm on screw, and making
sure arm is level, mark 3 additional drilling
locations. Drill holes, insert anchors (W-B),
then mount arm using screws (W-A) with
washers (W-C).
6m m
W-B
W-C
W-A
TOOLS NEEDED
Phillips
Screwdriver Drill Pencil
STEP 2
Slide decorative covers (D) on
arm (A).
STEP 3
Remove knob and slide VESA
plate o from bracket. Set parts
aside for later use.
STEP 4
Remove two lower screws from
back of pole (B) and set aside.
Attach tray (C) to pole using
M8x24 bolts (E), and tighten
with 6mm Allen wrench (G).
D
G
F
E
4
Slide VESA plate with monitor onto mounting
bracket of pole (B) and secure with previously
removed knob.
STEP 7
Adjust gas spring strength using 6mm Allen
wrench (G). Turning clockwise will decrease
strength, and counter-clockwise will increase
strength.
STEP 8
Loosen top two screws on back of pole (B) until 5mm of thread is exposed on each. Slide pole onto
mount of arm (A). Attach with previously removed screws, and tighten all screws with 4mm Allen
wrench (F).
STEP 5
OPTION A: Flat Back Monitor
For flat back monitor, attach VESA
plate using 12mm screws (M-A or
M-B) with washers (M-E).
STEP 6
OPTION B: Curved Back Monitor
For curved back monitor, attach VESA
plate using 12mm screws (M-C or M-D)
with washers (M-E) and spacers (M-F).
5m m
F
1 2
F
3
M- A
M- B
M- E
M- C
M- D
M- E
M- F
G
NOTE: Tighten socket set screw if the joint
makes a popping noise.
5
Adjust height of monitor using knob on pole (B) as shown in diagram. Adjust tilt of monitor using
6mm allen wrench (G) as shown in diagram. Adjust rotation of tray (C) using 4mm allen wrench (F) as
shown in diagram if tray (C) is not level.
STEP 9
F
+4° -4°
G
+15°
-15°
STEP 10
To adjust tray to 10° tilt angle, first flip the tray up fully, then turn the supports in front of the hinge
upward. Set the keyboard tray back down. Allen wrenches (F, G) can be stored underneath the
keyboard tray as shown.
0°
10° 10 °
F
G
STEP 11
Turn knobs on mount (H) counterclockwise to remove. Take apart mount (H).
H
6
STEP 14
Place computer in mount (H) and tighten with straps (I).
Attach straps (I) to small half of mount (H) as shown in diagram. Place mount against wall where
desired and mark holes with a pencil. Drill 2.4” (60mm) deep holes using a 3/8” (10mm) drill bit, and
insert anchors (W-B). Use screws (W-A) to attach mount to wall.
STEP 12
STEP 13
Replace second half of mount (H) and secure with knobs as shown in diagram. Attach straps (I) to
second half of mount (H).
NOTE: The CPU mount is only designed for mounting to a brick or concrete wall.
I
2
W- B W- A
1
2
2
1
7
STEP 16
Insert cables making sure there is enough slack
for full movement, then re-install covers.
Adjust as Desired
STEP 15
Use screwdriver to remove screws securing
the cable covers.
1
2
1
2
+15°
-15°
180 °
180 °
LAST UPDATED: 03/06/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de De oficina de Vivo
Vivo
Vivo DESK-V000M Manual de usuario
Vivo
Vivo DESK V001G Manual de usuario
Vivo
Vivo DESK-V100ZE Manual de usuario
Vivo
Vivo DESK-V000Q Manual de usuario
Vivo
Vivo DESK-V000V Series Manual de usuario
Vivo
Vivo CART-V00LW Manual de usuario
Vivo
Vivo DESK-V000V Series Manual de usuario
Vivo
Vivo DESK-V000VS Manual de usuario
Vivo
Vivo DESK-V001A Manual de usuario
Vivo
Vivo DESK-LEGS1K Manual de usuario
Vivo
Vivo DESK-V001D Manual de usuario
Vivo
Vivo STAND-SIT2E Manual de usuario
Vivo
Vivo DESK-V000LC Manual de usuario
Vivo
Vivo DESK-V000KL Manual de usuario
Vivo
Vivo CART-V08D Manual de usuario
Vivo
Vivo DESK-V000VW Manual de usuario
Vivo
Vivo DESK-V000J Manual de usuario
Vivo
Vivo STAND-SIT2W Manual de usuario
Vivo
Vivo DESK-V000L Manual de usuario
Vivo
Vivo DESK-V000EB V000EB Manual de usuario
