Vitek Transcendent Series Manual de usuario

VITEK

PLEASE NOTE:

Complete User Guide, Software, Tools, and Updates are

available online. Scan the QR Code or visit:

http://www.vitekcctv.com/Downloads

VTD-TND6FP

Transcendent Series 6

Megapixel H.265 IP Vandal 360°

Fisheye Camera w/6 IR LEDs

QUICK START GUIDE

FEATURES

• 1/2.9” 6.0 MegaPixel CMOS Image Sensor

• Up to 30fps live view @ 6 MegaPixel

• Multiple Views: 360° Overview, Double 180° Panorama View, Overview

+ 3 Views, and Single View

• 1.07mm @ F2.5 Fisheye Lens with 180° horizontal field of view (wall

mounted) / 360° (ceiling mounted)

• 6 High Power Covert IR LEDs with 50’ IR Range

• True Mechanical Day/Night function by ICR

• XD-DNR (2D-DNR & 3D-DNR) Noise Reduction

• ROI Encoding

• H.265/H.264/MJPEG Triple Streaming

• Secondary Video Output (CVBS)

• Remote Viewing via CMS, Internet Explorer, and iOS & Android Apps

• ONVIF Compliant

• MicroSD memory card slot for Local recording supporting up to 128GB

MicroSDXC cards

• IK10 Impact Resistance Rating

• Two Way Audio

• 12VDC & PoE (Power over Ethernet) Operation

Overview

Components and Accessories

Camera

Quick Guide

Screws

Hex Wrench

Drill Template

Plastic Wall Anchors

Waterproof Cap

RJ-45 Ethernet

Audio In

Audio Out

CVBS Output

Alarm I/O

RS-485

Power Cable

MicroSD Card Slot

Reset

Network Cable & Power Connections

First connect the Waterproof Cap to an Ethernet patch cable, then

connect the cameras ethernet adaptor. If not powering the camera with

PoE, also connect the power Cable to an approved 12VDC Power

Supply.

Weather Resistant Network Coupler

1. Loosen the nut from the Weather Resistant Network Coupler,

2. Run ethernet cable through coupler, then attach a RJ-45 connector.

3. Tighten the nut and coupler for a weather resistant seal.

ALM-COM

ALM-OPEN

ALM-INA

ALM-GND

RS485T+

RS485T-

12VDC

Optional 12VDC

Power Connection.

Not needed with PoE

SD Card Installation

Gap

Fixed Ring

1. Remove the fixed ring from the camera.

2. Loosen the screws of the cover of the SD card and then insert

the SD card. Then reinstall the cover ring.

Installation

Before beginning installation, make sure that the wall or ceiling is

strong enough to withstand 3 times the weight of the camera. The

mounting steps are as follows:

1. Remove the fixed ring

from the gap of the

camera (see Install SD

Card)

2. Drill the screw holes and

the cable hole on the

wall according to the

drill template.

3. Route and connect the

cables.

4. Fix the camera to the

wall with screws as

shown.

5. Install the fixed ring

back onto the camera.

∅5.12”

∅0.18”

3.31”

3.82”

LAN Configuration

The camera can be accessed on the local network either using the

IP-Tool or directly in a web browser.

Accessing the Camera Using the IP-Tool

1. Make sure the camera and PC are connected to the LAN.

2. Locate the IP-Tool installer on the included Product Documentation

CD, then install on the PC. Open the installed application.

3. Modify the IP address. The default IP address is 192.168.226.201.

Click the information of the camera listed in the above table to show

the network information on the right side. Modify the IP address and

gateway of the camera and make sure its network address is in the

same local network segment as the computer’s. Please modify the

IP address of your device according to the practical situation.

For example, the IP address of your computer

is 192.168.13.4. So the IP address of the

camera shall be changed to 192.168.13.X.

After modification, please input the password

of the administrator and click “Modify” button

to modify the setting.

** Default admin password: “123456".

4. Double-click the IP address and then the system will pop up the web

browser to connect IP-CAM . IE browser will download the Active X

control automatically. After downloading, a login window will pop up

as shown below:

Input the user name and password to log in.

Default user name: admin / Default password: 123456.

Directly Access Through a Web Browser

The default network settings are as shown below:

IP address: 192.168.226.201 HTTP: 80

Subnet Mask: 255.255.255.0 Data Port: 9008

Gateway: 192.168.226.1

You may use the above default settings when you log in the camera for

the first time.

1. Manually set the IP address of the PC and the network segment

should be as the same as the default settings of IP-CAM. Open the

network and share center. Click “Local Area Connection” to pop up

the following window.

Select “Properties” and then select Internet protocol according to the

actual situation (for example: IPV4). Next, click “Properties” button to

set the network of the PC.

2. Open the IE Browser and input the default address of IP-CAM and

confirm. The IE browser will download Active X control automatical-

ly.

3. After downloading Active X control, the login dialog box will pop up.

4. Input the default username and password and then enter to view.

WAN Configuration

Access the camera by the router or virtual server for example.

1. Make sure the camera is connected to the LAN; Then log into the

camera via LAN and go to System Congfig→Network Config→Port

menu to set up the port number.

2. Enter System Config→Network Config→IP Address menu to modify

the IP address.

4. Open the web browser and input its WAN IP and HTTP port to

access the IP-CAM.

3. Go to the router’s management interface through IE browser to

forward the IP address and port of IP-CAM in the “Virtual Server”.

NOTES:

OPTIONAL ACCESSORIES

AND RELATED PRODUCTS FOR

TRANSCENDENT IP CAMERAS

INTRODUCING OUR NEWINTRODUCING OUR NEW

VT-TNR3216PF

VT-TNR818PF

VT-TNR1646PF

• 8MP (4K) HDMI Output

• H.265 / H.264 Compression

• Full Analytic Support Including

Face Detection

• 360 Degree / Fisheye De-Warping

• Available in 8, 16, and 32 Channels

• Up to 80TB Depending on Model

• PoE Support on ALL Models

ADVANCED LEARNING NVRs

A Standalone

Solution with FULL

Analytic Support

Otros manuales para Transcendent Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara IP de Vitek

Vitek

Vitek Transcendent VT-TPTZ-B10X5N Manual de usuario

Vitek

Vitek VTC-TNB42R3F Manual de usuario

Vitek

Vitek Transcendent VTC-TNB8RFA3-2 Manual de usuario

Vitek

Vitek VTC-TNB5RFS/-2 Manual de usuario

Vitek

Vitek VTD-IR2811DN Manual de usuario

Vitek

Vitek VTC-BHOCRAZE Manual de usuario

Vitek

Vitek VTC-IRA24F Manual de usuario

Vitek

Vitek VTC-IR303-212NP Manual de usuario

Vitek

Vitek VT-PIRC2T Manual de usuario

Vitek

Vitek VTD-TND30R3V Manual de usuario

Vitek

Vitek VTC-C2NZ Manual de usuario

Vitek

Vitek VTD-MS2810DN Manual de usuario

Vitek

Vitek VTC-IR403-212NP Manual de usuario

Vitek

Vitek Transcendent 5 Series Manual de usuario

Vitek

Vitek VTD-THD2RFE Manual de usuario

Manuales populares de Cámara IP de otras marcas

FLIR

FLIR Exx series Manual de usuario

Avigilon

Avigilon H4A-BO1-IR Manual de usuario

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manual de usuario

ShareTech

ShareTech AV1 Manual de usuario

Ezviz

Ezviz C6C Manual de usuario

Melchioni

Melchioni UCAM 2015 Manual de usuario

Geutebruck

Geutebruck G-Cam/ESD-4630 Manual de usuario

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manual de usuario

Mitel

Mitel 6800i Series Manual de servicio

THOMSON

THOMSON DSC - 323W Manual de usuario

AVer

AVer FB2027 Manual de usuario

ENFORCER

ENFORCER EV-T5105-N2SQ Manual de usuario

Wansview

Wansview NC543 Manual de usuario

Eneo

Eneo MCB-64A0003M0A Manual de usuario

deView electronics

deView electronics CBDNI36F Manual de usuario

Swann

Swann SwannEye Manual de usuario

LevelOne

LevelOne IP CamSecure Manual de usuario

Digitus

Digitus DN-16085-1 Manual de usuario