Vitek VT-8241 Manual de usuario

Фен-щётка

VT-8241

Hot air styler

IM VT-8241_70x130.indd 1 7/23/19 7:01 PM

IM VT-8241_70x130.indd 2 7/23/19 7:01 PM

ENGLISH

HOT AIR STYLER VT-8241

The hot air styler is used for styling dry or slightly wet hair.

DESCRIPTION

Attachment installation place

Attachment release button

Operation mode switch «0- -1-2»

Light indicator

Body

Air inlet grid

Hanging loop

Thermal brush 20 mm in diameter

Thermal brush 33 mm in diameter

10.

Diffuser

11.

Nozzle

ATTENTION!

•

Do not use the unit near water in the bathrooms, show-

ers, swimming pools etc.

•

After using the unit in a bathroom, unplug it by taking

the power plug out of the mains socket, as closeness

of water is dangerous even if the unit is switched off.

•

For additional protection you may install a residual cur-

rent device (RCD) with nominal operation current not

exceeding 30 mA into the bathroom mains; contact

a specialist for installation.

SAFETY MEASURES

Before using the unit, read this manual carefully and keep

it for future reference.

Use the unit for intended purposes only, as specified in

this manual. Mishandling the unit can lead to its break-

age and cause harm to the user or damage to his/her

property.

•

Before switching the hot air brush on, make sure that

your home mains voltage corresponds to the unit oper-

ating voltage.

•

To avoid fire, do not use adapters for connecting the

unit to the mains.

•

Do not use the unit outdoors.

•

Use only the attachments supplied.

•

When using the unit, we recommend to unwind the

power cord to its full length.

IM VT-8241_70x130.indd 3 7/23/19 7:01 PM

ENGLISH

•

The power cord may not:

–

touch hot objects,

–

run over sharp edges,

–

be used for carrying the unit.

•

Check the power cord and power plug insulation integ-

rity periodically.

•

Do not switch the unit on in places where aerosols are

sprayed or highly flammable liquids are used.

•

Hair spray shall be applied only after hair styling is

finished.

•

Do not operate the unit while taking a bath.

•

Never leave the operating unit unattended.

•

Do not touch the unit body, the power cord and power

plug with wet hands.

•

Do not place and do not keep the unit in places, where

it can fall into a bath or a sink filled with water, do not

immerse the unit into water or other liquids.

•

If the unit is dropped into water, unplug it immediately,

and only then take it out of the water.

•

Do not use the unit when you are drowsy.

•

Do not use the unit to style wet hair or synthetic wigs.

•

Avoid contact of heated surfaces with your face, neck

and other parts of your body.

•

Do not drop the unit.

•

Do not put the operating unit on heat-sensitive or soft

surfaces (for instance, bed or sofa) and do not cover it.

•

Do not direct hot air into your eyes or other heat-sensi-

tive parts of your body.

•

The attachments get hot during use. Allow them to cool

down before removal.

•

Never insert any foreign objects into any unit body

openings.

•

Never block the air inlets of the hot air brush, do not

place it on a soft surface (a bed or sofa), where the air

inlets may be blocked. Keep the air inlets free of lint,

dust and hair etc.

•

Avoid getting of hair into the air inlet grid during opera-

tion of the unit.

•

Clean the unit regularly.

•

Unplug the unit after every usage and before cleaning.

•

When unplugging the unit, pull the power plug but not

the power cord.

IM VT-8241_70x130.indd 4 7/23/19 7:01 PM

ENGLISH

•

For children safety reasons do not leave polyethylene

bags used as packaging unattended.

ATTENTION! Do not allow children to play with polyeth-

ylene bags or packaging film. Danger of suffocation!

•

Do not allow children to touch the unit body, the power

cord or the power plug during operation of the unit.

•

Do not leave children unattended to prevent using the

unit as a toy.

•

Close supervision is necessary when children or dis-

abled persons are near the operating unit.

•

This unit is not intended for usage by children. Place

the unit out of reach of children during the operation

and cooling down.

•

The unit is not intended for usage by physically or men-

tally disabled persons (including children) or by per-

sons lacking experience or knowledge if they are not

under supervision of a person who is responsible for

their safety or if they are not instructed by this person

on the usage of the unit.

•

Do not use the unit if the power plug or the power cord

is damaged, if the unit works improperly and after it

was dropped.

•

If the power cord is damaged, it should be replaced by

the manufacturer, maintenance service or similar quali-

fied personnel to avoid danger.

•

Do not attempt to repair the unit. Do not disassemble

the unit by yourself, if any malfunction is detected or

after it was dropped, unplug the unit and apply to any

authorized service center from the contact address

list given in the warranty certificate and on the website

www.vitek.ru .

•

To avoid damages, transport the unit in the original

package only.

•

Keep the unit in a dry cool place out of reach of children

and disabled persons.

THE UNIT IS INTENDED FOR HOUSEHOLD USE ONLY,

ITS COMMERCIAL USAGE AND USAGE IN PRODUCTION

AREAS AND WORK SPACES IS PROHIBITED.

USING THE HOT AIR STYLER

After the unit transportation or storage at low temperature keep

it for at least three hours at room temperature.

IM VT-8241_70x130.indd 5 7/23/19 7:01 PM

ENGLISH

•

Unpack the hot air styler and remove any stickers that can

prevent unit operation.

•

Unwind the power cord completely.

•

Install one of the attachments (8, 9, 10, 11). To do this insert

the attachment into the installation place (1) and turn it

clockwise. If the attachment is set properly, you will hear

the release button (2) click.

•

Before switching the unit on, make sure that your home

mains voltage corresponds to the unit operating voltage.

•

The unit is intended for operation with AC system and

50 Hz or 60 Hz frequency, the unit does not need any

additional settings for operating with the required nomi-

nal frequency.

•

Make sure that the operation mode switch (3) is set to the

position “0”.

•

Insert the power plug into the mains socket.

•

Use the switch (3) to set the required parameters of the air

flow, the indicator (4) will be glowing during the operation:

«0» – the hot air styler is off;

« » – «cool» air supply;

«1» – low air flow temperature;

«2» – high air flow temperature;

Note: During the first operation some foreign smell and a

small amount of smoke from the heating element are possible,

this is normal.

•

After the hot air styler operation is finished, switch it off

by setting the switch (3) to the «0» position and unplug it.

•

Wait till the hot air styler cools down.

•

To remove the attachment, press and hold the attach-

ment release button (2) and turn the attachment coun-

terclockwise.

Overheating protection

Overheating protection switches the hot air styler off if the

temperature of the outgoing air is above the limit. If the hot air

styler is switched off during operation, set

the switch (3) to the «0» position, unplug the unit and make

sure that the inlets and outlets are unblocked. Let the unit cool

down for 5-10 minutes and switch it on again. Do not block the

air inlets during the hot air styler operation and avoid getting

of hair into its air inlet.

CLEANING AND CARE

The hot air styler is intended for household use only.

IM VT-8241_70x130.indd 6 7/23/19 7:01 PM

ENGLISH

•

Set the switch (3) to the «0» position, disconnect the hot air

styler from the mains and let it cool down.

•

To remove the attachment, press and hold the attach-

ment release button (2) and turn the attachment coun-

terclockwise.

•

Wipe the unit body (5) with a damp cloth and then wipe

it dry.

•

Clean the air inlet grid (6) with a brush.

•

Never immerse the unit into water or any other liquids.

•

Do not use abrasives and solvents to clean the unit body.

STORAGE

•

Disconnect the unit from the mains and clean it.

•

Do not wind the power cord around the hot air styler, as this

can damage the cord or the unit body. Handle the power

cord with care, do not pull, twist or stretch it, especially

near the power plug or at the junction point. Straighten

the cord periodically if it gets twisted during the hot air

styler operation.

•

For easy storing there is a hanging loop (7), you can hang

the hot air styler on this loop provided that no water gets on

the unit in this position.

•

Keep the unit in a dry cool place out of reach of children

and disabled persons.

DELIVERY SET

Hot air styler – 1 pc.

Thermal brush 20 mm in diameter – 1 pc.

Thermal brush 33 mm in diameter – 1 pc.

Diffuser – 1 pc.

Nozzle – 1 pc.

Manual – 1 pc.

TECHNICAL SPECIFICATIONS

Power supply: 220-240 V ~ 50/60 Hz

Rated input power: 1000 W

ATTENTION! Do not use the unit near water in the bathrooms,

showers, swimming pools etc.

IM VT-8241_70x130.indd 7 7/23/19 7:01 PM

ENGLISH

RECYCLING

For environment protection do not throw out the unit and

the batteries (if included), do not discard the unit and the

batteries with usual household waste after the service

life expiration; apply to specialized centers for further

recycling.

The waste generated during the disposal of the unit is

subject to mandatory collection and consequent disposal

in the prescribed manner.

For further information about recycling of this product

apply to a local municipal administration, a disposal service

or to the shop where you purchased this product.

The manufacturer preserves the right to change design,

structure and specifications not affecting general princi-

ples of the unit operation without a preliminary notification

due to which insignificant differences between the manual

and product may be observed. If the user reveals such

differences, please report them via e-mail [email protected]

for receipt of an updated manual.

Unit operating life is 3 years

Guarantee

Details regarding guarantee conditions can be obtained

from the dealer from whom the appliance was purchased.

The bill of sale or receipt must be produced when making

any claim under the terms of this guarantee.

This product conforms to the EMC Directive

2014/30/EU and to the Low Voltage Directive

2014/35/EU.

IM VT-8241_70x130.indd 8 7/23/19 7:01 PM

РУССКИЙ

ФЕН-ЩЁТКА VT-8241

Фен-щётка используется для укладки сухих или слегка

влажных волос.

ОПИСАНИЕ

Место установки насадок

Клавиша-фиксатор насадок

Переключатель режимов работы «0- -1-2»

Световой индикатор

Корпус

Воздухозаборная решётка

Петелька для подвешивания

Термощётка диаметром 20 мм

Термощётка диаметром 33 мм

10.

Диффузор

11.

Насадка-концентратор

ВНИМАНИЕ!

•

Не использовать прибор вблизи воды в ванных комна-

тах, душевых, бассейнах и т.д.

•

После использования устройства в ванной комнате

отключите его от электрической сети, вынув вилку

сетевого шнура из электрической розетки, так как бли-

зость воды представляет опасность даже в тех случаях,

когда устройство выключено выключателем.

•

Для дополнительной защиты в цепи питания ванной

комнаты целесообразно установить устройство защит-

ного отключения (УЗО) с номинальным током срабаты-

вания, не превышающим 30 мА; при установке следует

обратиться к специалисту.

МЕРЫ БЕЗОПАСНОСТИ

Перед началом эксплуатации электроприбора внимательно

прочитайте настоящее руководство и сохраните его для

использования в качестве справочного материала.

Используйте устройство только по его прямому назначе-

нию, как изложено в данном руководстве. Неправильное

обращение с прибором может привести к его поломке,

причинению вреда пользователю или его имуществу.

•

Перед включением фена-щётки убедитесь в том, что

напряжение электрической сети соответствует рабоче-

му напряжению устройства.

•

Во избежание пожара не используйте переходники

при подключении устройства к электрической розетке.

•

Не используйте устройство вне помещений

IM VT-8241_70x130.indd 9 7/23/19 7:01 PM

РУССКИЙ

•

Применяйте только насадки, которые входят в ком-

плект поставки.

•

При эксплуатации прибора рекомендуется размотать

сетевой шнур на всю длину.

•

Сетевой шнур не должен:

– соприкасаться с горячими предметами,

– протягиваться через острые кромки,

– использоваться для переноски прибора.

•

Периодически проверяйте состояние изоляции сетево-

го шнура и сетевой вилки.

•

Не включайте устройство в местах, где распыляются

аэрозоли или используются легковоспламеняющиеся

жидкости.

•

Наносите лак для волос только после моделирования

причёски.

•

Не используйте прибор во время принятия ванны.

•

Никогда не оставляйте работающий прибор без при-

смотра.

•

Не беритесь мокрыми руками за корпус, сетевой шнур

и вилку сетевого шнура.

•

Не кладите и не храните устройство в местах, где

оно может упасть в ванну или раковину, наполненную

водой, не погружайте устройство в воду или в любую

другую жидкость.

•

Если устройство упало в воду, немедленно извлеки-

те сетевую вилку из электрической розетки, и только

после этого можно достать прибор из воды.

•

Не используйте устройство, если вы находитесь в сон-

ном состоянии.

•

Не используйте прибор для укладки мокрых волос или

синтетических париков.

•

Избегайте соприкосновения горячих поверхностей

устройства с лицом, шеей и другими частями тела.

•

Не роняйте устройство.

•

Не кладите устройство во время работы на чувстви-

тельные к теплу поверхности, на мягкую поверхность

(например, на кровать или диван) и не накрывайте его.

•

Не направляйте горячий воздух в глаза или на другие

теплочувствительные части тела.

•

Насадки во время работы нагреваются. Перед их сня-

тием дайте им остыть.

•

Не вставляйте посторонние предметы в любые отвер-

стия корпуса.

•

Запрещается закрывать воздушные отверстия фена,

не кладите его на мягкую поверхность (на кровать или

IM VT-8241_70x130.indd 10 7/23/19 7:01 PM

Tabla de contenidos

Idiomas:

Otros manuales de Peinador de cabello de Vitek

Vitek

Vitek VT-8248 Manual de usuario

Vitek

Vitek VT-2297 PK Manual de usuario

Vitek

Vitek VT-8239 PP Manual de usuario

Vitek

Vitek VT-8237 Manual de usuario

Vitek

Vitek VT-1326 Manual de usuario

Vitek

Vitek VT-8240 BN Manual de usuario

Vitek

Vitek VT-8238 VT Manual de usuario

Vitek

Vitek VT-2296 BK Manual de usuario

Vitek

Vitek VT-8247 Manual de usuario

Vitek

Vitek VT-8238 Manual de usuario

Vitek

Vitek VT-8433 Manual de usuario

Vitek

Vitek VT-1330 Manual de usuario

Vitek

Vitek VT-8240 Manual de usuario

Vitek

Vitek VT-8235 VT Manual de usuario

Vitek

Vitek VT-8249 Manual de usuario

Vitek

Vitek VT-1315 Manual de usuario

Vitek

Vitek Curly lady Manual de usuario

Vitek

Vitek VT-8435 Manual de usuario

Vitek

Vitek VT-2533 VT Manual de usuario

Vitek

Vitek VT-8236 Manual de usuario

Vitek

Vitek VT-1324 Manual de usuario

Vitek

Vitek VT-2285 Manual de usuario

Vitek

Vitek VT-1327 Manual de usuario

Vitek

Vitek VT-2297 Manual de usuario

Manuales populares de Peinador de cabello de otras marcas

Philips

Philips HP8309 Manual de usuario

Eldom

Eldom bess HTS20 Manual de usuario

Lunata Hair

Lunata Hair LH24HR Instrucciones originales

Conair

Conair S3CSC Manual de usuario

Remington

Remington CI89H1 Manual de usuario

Dyson

Dyson Airwrap Manual de usuario

Braun

Braun Satin Hair 1 AS 110 Guía rápida

REVAMP Professional

REVAMP Professional iGEN PROGLOSS CL-2750 Manual de usuario

point

point WAVE VIXEN TRIPLE WAVE MAKER Manual de usuario

Braun

Braun Satin Hair 5 Manual de usuario

Philips

Philips beauty Airstylist quattro 600 Manual de usuario

Grundig

Grundig HS 7230 Manual de usuario

Philips

Philips HP4658/08 Manual de usuario

Remington

Remington AS7100 Manual de usuario

HOT TOOLS

HOT TOOLS SIGNATURE Series Guía de instalación

Conair

Conair INFINITI INFCS25C Manual de usuario

Philips

Philips Norelco RQ111 Manual de lista de piezas

Clas Ohlson

Clas Ohlson 44-1152 Manual de usuario