Vista 12V Series Manual de usuario

INSTALLATION INSTRUCTIONS Step and Brick Lights

4242

Fixture cover

Wood

staircase

18-2 Pigtail

Main supply

cable

Flexible or

PVC conduit

(by others)

Fixture housing/

Junction box

Side clamp bracket

for existing walls

Reflector

retaining

screw

Concrete

Reflector

Cover

screws

TOOLS REQUIRED FOR

INSTALLATION:

●Wire strippers

●Blade head screwdriver

●Phillips head screwdriver

●Cutting saw

●Drill

FOR USE ONLY WITH LOW VOLTAGE LANDSCAPE POWER UNITS THAT DO NOT EXCEED 25 AMPS, 15 VOLT MAXIMUM.

WARNING: Luminaires must be installed in accordance with the National Electrical Code (NEC) and local codes.

Failure to do so will void the warranty and may result in serious injury and/or damage to the luminaire.

SAFETY WARNING: Luminaire can become very hot depending on lamp wattage used. Lens and metal around

lamp can become hot enough to blister hands. Particular care should be taken not to locate luminaires where

small children can reach them if high wattage lamps are used.

LUMINAIRES ARE NOT TO BE INSTALLED WITHIN 10 FT. (3.05M) OF A POOL OR SPA. SECONDARY CABLE IS NOT TO

BE BURIED MORE THAN 6”. WHEN USING MULTIPLE LUMINAIRES, LOAD IS NOT TO EXCEED THE TOTAL WATTS OF

TRANSFORMER RATING. DO NOT USE EXTENSION CORDS ON POWER UNITS.

NOTE: Always use UL recognized wire connectors for connections.

NOTE: Save these instructions for future reference.

INSTRUCTIONS FOR EXISTING WALLS/WOOD DECK MOUNTING:

1. To prevent electrical shock, disconnect transformer from electrical supply before installation or service.

2. Remove reector assembly from luminaire.

3. Using luminaire housing as a template, mark the location of the housing on the wall or deck.

4. Cut hole in wall or deck to accept housing.

NOTE: Remove any insulation within six (6) inches of where luminaire will be mounted.

5. Insert housing into cut hole and secure tightly against wall or deck.

6. Using the two (2) blue wirenut connectors (provided), connect the wire leads from behind

the reector to the 18-2 cable pigtail (provided) exiting the luminaire (see diagram).

7. Install reector and lamp.

8. Install cover plate to luminaire and tighten screws evenly (see diagram).

9. Strip the two (2) leads from the luminaire wire. Using the two (2) silicone lled safety

connectors (provided), connect the leads from the luminaire to the main supply cable

leads (see diagram).

10. Provide power to the luminaire and check for proper operation.

12V SERIES

1625 Surveyor Avenue • Simi Valley, CA 93063 • (805) 527-0987 • (800) 766-VISTA (8478)

FAX: (888) 670-VISTA (8478) • [email protected] • www.vistapro.com

IMPORTANT SAFETY INSTRUCTIONS

THE LIGHTED LAMP IS HOT!!

WARNING: TO REDUCE THE RISK OF FIRE, OR INJURY TO

PERSONS:

1. Turn off/unplug and allow to cool before replacing lamp.

2. Lamps get hot quickly! Contact only switch/plug when turning on.

3. Do not touch hot lens, guard or enclosure.

4. Keep lamp away from material that may burn.

5. Do not touch the lamp at any time. Use a soft cloth. Oil from the skin may

damage lamp.

6. Do not operate luminaire tting with a missing or damaged cover.

LAMP INSTALLATION/REPLACEMENT:

CAUTION: Do not exceed maximum wattage marked on luminaire label.

1. To prevent electrical shock, disconnect transformer from electrical supply before service.

2. Loosen cover screws and remove cover.

3. Replace lamp with correct wattage and type as marked on luminaire label.

NOTE: DO NOT touch Halogen lamp with bare hands. Always use a soft cloth or

the plastic wrapping (if available) from the lamp to handle the lamp.

6. Re-install cover and tighten screws evenly.

1625 Surveyor Avenue • Simi Valley, CA 93063 • (805) 527-0987 • (800) 766-VISTA (8478)

FAX: (888) 670-VISTA (8478) • [email protected] • www.vistapro.com

INSTRUCTIONS FOR MASONRY OR CONCRETE WALL MOUNTING:

NOTE: For pour concrete installation a conduit connection is required.

1. Remove reector assembly from luminaire.

2. Using standard masonry procedures, build wood support frame and secure luminaire to support frame.

NOTE: Optional mounting brackets for some models are available to facilitate installation in concrete walls.

NOTE: UL listed exible conduit is recommended for connections to ease luminaire

position and adjustment during installation.

3. Remove 1/2” knockout from the side or bottom of luminaire.

4. Connect conduit (by others) and pull supply wires through into housing.

5. Cover opening of luminaire with cardboard and be sure all unused electrical plugs (knockouts)

are closed before concrete pour.

6. Pour concrete using standard masonry procedures.

7. Using the UL listed wirenut connectors (provided), connect the wire leads from behind

the reector to the 18-2 cable pigtail (provided) exiting the luminaire (see diagram).

8. Install reector and lamp.

9. Install cover plate to luminaire and tighten screws evenly (see diagram).

10. Strip the two (2) leads from the luminaire wire. Using the two (2) silicone lled safety connectors (provided), connect the

leads from the luminaire to the main supply cable leads (see above).

11. Provide power to the luminaire and check for proper operation.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Luz exterior de Vista

Vista

Vista Landscape Series Manual de usuario

Vista

Vista Architectural Series Manual de usuario

Vista

Vista 2125 Manual de usuario

Vista

Vista 6223 Landscape Series Manual de usuario

Vista

Vista 4017 Manual de usuario

Vista

Vista 2130 Series Manual de usuario

Vista

Vista 5290 Manual de usuario

Vista

Vista Landscape Series Manual de usuario

Vista

Vista 6219 Landscape Series Manual de usuario

Vista

Vista 5203 Series Manual de usuario

Vista

Vista 1218 Manual de usuario

Vista

Vista 1455 Manual de usuario

Vista

Vista 7223 Landscape Series Manual de usuario

Vista

Vista 1039 Manual de usuario

Vista

Vista 12V Series Manual de usuario

Vista

Vista Landscape Series Manual de usuario

Vista

Vista 5237 Manual de usuario

Vista

Vista 5204 Manual de usuario

Vista

Vista 2117 Manual de usuario

Vista

Vista PDK-75-5047 Manual de usuario

Vista

Vista 6216 Landscape Series Manual de usuario

Vista

Vista 9216 Landscape Series Manual de usuario

Vista

Vista Landscape Series Manual de usuario

Vista

Vista 2165 Manual de usuario

Manuales populares de Luz exterior de otras marcas

Sealey

Sealey LED37 Manual de usuario

nordlux

nordlux VEJERS Guía del usuario

SImx

SImx ELITE LED LHTC637 Manual de usuario

GEV

GEV CAROLINE 10833 Manual de usuario

NEBO

NEBO NEB-LSP-0020 Manual de usuario

WE-EF

WE-EF PFL540 LED Manual de usuario

Lindby

Lindby 9949029 Manual de usuario

HEPER

HEPER DOGO Side LW6048.585-US Instrucciones de instalación y funcionamiento

HEPER

HEPER LW8034.003-US Instrucciones de instalación y funcionamiento

Maretti

Maretti VIBE S 14.6080.04.A Manual de usuario

BEGA

BEGA 84 253 Manual

HEPER

HEPER MINIMO Instrucciones de instalación y funcionamiento

LIGMAN

LIGMAN BAMBOO 3 Manual de usuario

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Manual de usuario

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Manual de usuario

urban ambiance

urban ambiance UQL1273 Manual de usuario

TotalPond

TotalPond 52238 Manual de usuario

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Manual de usuario