VISIONARY DESIGNS VK-2313 Manual
© 2017
www.classicexhibits.com
Order #XXXXX
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
VK-2313 - 10’x20’ Inline Display
20’
10’
Plan View
Perspective View
© 2017
www.classicexhibits.com
Order #XXXXX General Information
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
© 2017
www.classicexhibits.com
Order #XXXXX General Information
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
SEG Graphic Installation
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
© 2017
www.classicexhibits.com
Order #XXXXX
Step 1 of 3
Backwall 10x10 LEFT Assembly
Item
1
2
3
4
5
6
7
8
Description
45” SEG Extrusion
45” SEG Extrusion
45” SEG Extrusion
45” SEG Extrusion
45” SEG Extrusion
45” SEG Extrusion
45” SEG Extrusion
45” SEG Extrusion
1
4
2
3
5
6
7
8
Setups:
1) Assembled SEG extrusions together on floor.
2) Apply SEG graphic to assembled frame.
3) Attach foot to side of assembled frame
where indicated.
See Detail C on
General Info Page.
When
assembled
Center
*
*
*
Tighten knob
to secure
Hook keyhole cut
out up bolt
Foot Attachment
*
*
TSP49
Lock
Tighten setscrew
to secure
extrusions
TSV1 Lock Detail
© 2017
www.classicexhibits.com
Order #XXXXX
Step 2 of 3
Backwall 10x10 RIGHT Assembly
1
4
2
3
5
6
7
8
When
assembled
*
*
*
*
Item
1
2
3
4
5
6
7
8
Description
45” SEG Extrusion
45” SEG Extrusion
45” SEG Extrusion
45” SEG Extrusion
45” SEG Extrusion
45” SEG Extrusion
45” SEG Extrusion
45” SEG Extrusion
Setups:
1) Assembled SEG extrusions together on floor.
2) Apply SEG graphic to assembled frame.
3) Attach foot to side of assembled frame
where indicated.
Tighten knob
to secure
Hook keyhole cut
out up bolt
Foot Attachment
*
See Detail C on
General Info Page.
Center
*
TSP49
Lock
Tighten setscrew
to secure
extrusions
TSV1 Lock Detail
© 2017
www.classicexhibits.com
Order #XXXXX
Step 3 of 3
Center Connection
When
assembled
**** See attached SEG graphic
installation for graphic attachment
Setups:
1) Connect two assembled SEG frames together using bolts as shown.
2) Apply SEG graphics to assembled frame. Refer to details.
Otros manuales de Monitor de VISIONARY DESIGNS
VISIONARY DESIGNS
VISIONARY DESIGNS SEGUE DESIGNS VK-1350 Manual
VISIONARY DESIGNS
VISIONARY DESIGNS VK-2965 Manual
VISIONARY DESIGNS
VISIONARY DESIGNS VK-1332 Manual
VISIONARY DESIGNS
VISIONARY DESIGNS VK-2934 Manual
VISIONARY DESIGNS
VISIONARY DESIGNS VK-8008 Manual
VISIONARY DESIGNS
VISIONARY DESIGNS VK-1317 Manual
VISIONARY DESIGNS
VISIONARY DESIGNS VK-2956 Manual
VISIONARY DESIGNS
VISIONARY DESIGNS VK-1124 Manual
