Vilar VWC-300PT Manual de usuario

Thank you for purchasing a Vilar IP Camera. The IP-001A is a high performance IP

Camera. The camera provides many features such as steady net ork connection,

po erful customer management, compatibility and security. You can use it simple and

convenient.

This guide explains ho to install this camera fast. For more details, please refer to the [IP

Camera User Manual.doc] on accessory CD.

Connecting the LAN

Connect the net ork cable to the RJ45 net ork connection port.

Connect the po er adapter to the IP Camera po er socket and then insert the plug into an

available po er outlet.

Start up your computer, and make sure it connects to the LAN successfully. Click

Start>Running, and enter “command” (for Windo s 95/98/ME) or “cmd” (for

Windo s2000/XP). Then select “OK” and enter “ipconfig”, press enter. The basic setting

of your net ork ill be sho n as follo :

Please record the IP Address, Subnet Mas , and Default Gateway. You might use this

information to set your device.

Insert the accessory CD into the CD-ROM, copying the “VilarWizard_CN.exe” hich is

green soft are from the CD to your computer. Double-click it on your computer. The

interface as follo ill pup up.

This indo sho s us all the IP Cameras in your LAN. You can press the refresh button

to get a ne list.

If there are many cameras in your LAN, you can look for your camera by checking

camera’s “serial number”. The serial number is on the back cover of this guide.

If your IP Camera’s IP address is not as the same segment of your PC(defined by IP

Address and Net ork Mask), you may not be able to visit your IP Camera. For example,

Your PC’s IP address is 192.168.100.33, net ork mask is 255.255.255.0, then your PC

can visit the IP address from 192.168.100.1 to 192.168.100.255 only, If your IP Camera’s

IP Address is not in this range, you cannot access it. Therefore you can click [Setup IP]

button to change IP Camera’s IP address and adjust it adapting your PC setting.

Please fill in the LAN parameters hich ere you recorded before such as Subnet Mas ,

Default Gateway and IP Address. Attention of IP Address is the front three sections of IP

Address are the same as your recorded, but the last section you have to enter the number

is different from your computer. For example your PC IP address is 10.0.8.69; you can set

your camera IP address as 10.0.8.210. You might need contact your net ork administrator

to make sure ho to set the last number of your camera IP address.

For example:

Subnet Mas ：255.255.255.0

Default Gateway：10.0.8.1

IP Address：10.0.8.210

After that click [ok] and then enter the administrator’s username as “admin” and the

administrator pass ord as “123456”.

Click “OK”, the system starting assign a ne IP address for your IP camera.

Click “OK” after you sa the successfully prompt. Then ne IP address of your camera

has been sho n in the interface.

Selecting this camera, and click “visit IPCam” option, the Internet explorer ill connect

your camera automatically.

Above interface can be indicated means your IP camera is connect to net ork

successfully.

Also you can enter your camera IP address into the Internet explorer to access, such as

http://10.0.8.210

Click the “User Zone” button; you ill enter the image vie interface. The login indo ill

be indicated at the first time.

Please fill in the administrator’s username as “admin” and the administrator pass ord as

“123456” to enter the ebsite.

When you enter the ActiveX mode at the first time, you might be prompted to install the

ActiveX control. After you set the IE security option correctly, you ill see the follo dialog

box.

Click [Install] to continue. If you cannot see the message as above, you have to modify

the Internet Explorer security configuration.

Setting Internet Explorer (IE) security configuration ill execute follo ing steps:

1. Select [Internet Options] in [Tools] menu of IE;

2. S itch to [Security] option card;

3. Select [Custom Level];

4. Setup as the follo ing:

a) Init and Run unmar ed as safety ActiveX controls: Select [Alert];

b) downloading unsigned ActiveX controls: Select [Alert];

c) Run ActiveX controls and plug-in: Select [Enable];

5. Click [OK] to save it.

In addition the IPCam also can be a “Trusted Sites”, the setting process as follo :

1. Select [Internet Options] in [Tools] menu of IE;

2. S itch to [Security] option card;

3. Select [Trusted Sites];

4. Uncheck “√“ before “……https:(S) ”;

5. Enter IP Camera’s IP address or URL, for example, http://192.168.0.250 or

http://tom.vipcam.cn;

6. Click [Add], [OK] to save it.

Note: You can not download the ActiveX

Control without authorization until setup

Internet Explorer security configuration

properly.

The access from internet

Sometimes you might need to visit your IP camera from internet. Such as you ant to see

your pets hen you at office. You can control the home camera send the pets’ video to you

by using internet. You have to do some configurations of your router before you visit your

camera from internet.

You cam image there are many cameras and computers are connecting the same inside

net ork port of router. The router can get a public net ork IP address (such as

202.102.3.11) to connect the internet, ho ever it assign inside net ork port address for

each device as LAN IP address, such as 192.168.0.xxx.

You can choose follo methods to modify router configuration. After that the remote user

can visit your IP camera.

You can achieve this goal by enable Reversal NAT (RNAT) function of IP Sharing Device.

1. “Virtual Server”: Many routers have “Virtual Server” support. You must for ard the

WAN 80 TCP port to LAN IP Camera’s IP and Port. (If you visit 210.82.13.21’s 80 port

outside, you ill be for ard to LAN 192.168.0.2’s 80 port).

2. Another method is the “DMZ Host”. If enabled to use a LAN device as the DMZ host,

the outside PC ill be able visit this LAN device directly, as if there is no IP Sharing

Device exists. This method support only one LAN device exposed to the WAN. Thus, if

you have more IP Cameras, you have to use the above method.

The Dynamic Domain Name access

The dynamic domain name (DDN) access is using DDN system to mapping a user’s

dynamic IP address to a settled dynamic domain name service. It makes up of Server

program and Customer program. The Customer program sends the dynamic IP address of

host computer to Server program, and then the Server program update the data no . Also

the Server program can provide a settled domain name for customer. The ne IP address

ill be tied ith the settled domain name together by Server program. At this time the

dynamic domain name service (DDNS) is done, and your server can be visited by others.

The function of DDNS is achieving the resolution bet een dynamic IP address and settled

domain name. After getting the ne IP address, user has to apply update data from DNS

every time. When the user is online, someone ants to visit this domain name from

internet, the DDN server ill return to the correct IP address. To prevent a confusion

caused by reusing the same IP address, the DNS have to stop use the domain name

hen the user is offline.

The DDNS operating figure as follo :

In order to use DDNS you have to apply a DDNS domain name first. Please visit

http:// .vipcam.cn, enter the product serial number and original pass ord login. You

can find the serial number and pass ord of your camera in the back cover of this guide.

Setting your DDNS domain name and changing your pass ord on this page. Please enter

in common use e-mail address, because you can get back your pass ord easier hen you

forget your pass ord. After that visiting your camera on your computer, select “system

setting->networ setting” and set the “Dynamic domain name” option, it sho n as

follo :

Please choose “DDNS supplier”, enter your “User name” and “Password”, and then click

“apply”. The net ork camera ill reboot after that, if you see the current status is “update

Otros manuales para VWC-300PT

Otros manuales de Cámara IP de Vilar

Vilar

Vilar UP-009 Manual de usuario

Vilar

Vilar VWC-300PT Manual de usuario

Manuales populares de Cámara IP de otras marcas

FLIR

FLIR Exx series Manual de usuario

Avigilon

Avigilon H4A-BO1-IR Manual de usuario

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manual de usuario

ShareTech

ShareTech AV1 Manual de usuario

Ezviz

Ezviz C6C Manual de usuario

Melchioni

Melchioni UCAM 2015 Manual de usuario

Geutebruck

Geutebruck G-Cam/ESD-4630 Manual de usuario

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manual de usuario

Mitel

Mitel 6800i Series Manual de servicio

Vitek

Vitek VTC-IR403-212NP Manual de usuario

THOMSON

THOMSON DSC - 323W Manual de usuario

AVer

AVer FB2027 Manual de usuario

ENFORCER

ENFORCER EV-T5105-N2SQ Manual de usuario

Wansview

Wansview NC543 Manual de usuario

Eneo

Eneo MCB-64A0003M0A Manual de usuario

deView electronics

deView electronics CBDNI36F Manual de usuario

Swann

Swann SwannEye Manual de usuario

LevelOne

LevelOne IP CamSecure Manual de usuario