ViewSonic PJ506ED Manual de usuario

PJ506ED

DLP Projector

ViewSonic®

Model No. : VS11452

- User Guide

- Guide de l’utilisateur

- Bedienungsanleitung

- Guía del usuario

- Guida dell’utente

- Guia do usuário

- Användarhandbok

- Käyttöopas

-Pyководствопользователя

- 使用手冊 (繁體)

- 使用手冊(简体)

i PJ506EDViewSonic

Compliance Information

For U.S.A.

This device complies with part 15 of FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy, and if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modications not expressly approved by

the party responsible for compliance could void your authority to operate the equipment.

For Canada

• This Class B digital apparatus complies with Canadian ICES-003.

• Cet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

CE Conformity for European Countries

The device complies with the requirements of the EEC directive 89/336/

EEC as amended by 92/31/EEC and 93/68/EEC Art.5 with regard to

“Electromagnetic compatibility”, and 73/23/EEC as amended by 93/68/EEC

Art.13 with regard to “Safety.”

Following information is only for EU-member states:

The mark shown to the right is in compliance with the Waste Electrical and

Electronic Equipment Directive 2002/96/EC (WEEE).

The mark indicates the requirement NOT to dispose the equipment as

unsorted municipal waste, but use the return and collection systems

according to local law.

ii PJ506EDViewSonic

Important Safety Instructions

1. Read these instructions completely before using the equipment.

2. Keep these instructions in a safe place.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this equipment near water. Warning: To reduce the risk of re or electric

shock, do not expose this apparatus to rain or moisture.

6. Clean with a soft, dry cloth. If further cleaning is required, see “Cleaning the Display”

in this guide for further instructions.

7. Do not block any ventilation openings. Install the equipment in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or

other devices (including ampliers) that produce heat.

9. Do not attempt to circumvent the safety provisions of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than the other. A

grounding type plug has two blades and a third grounding prong. The wide blade

and the third prong are provided for your safety. If the plug does not t into your

outlet, consult an electrician for replacement of the outlet.

10. Protect the power cord from being tread upon or pinched, particularly at the plug,

and the point where if emerges from the equipment. Be sure that the power outlet is

located near the equipment so that it is easily accessible.

11. Only use attachments/accessories specied by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the equipment. When a cart is used, use

caution when moving the cart/equipment combination to avoid injury from

tipping over.

13. Unplug this equipment when it will be unused for long periods of time.

14. Refer all servicing to qualified service personnel. Service is required when the

unit has been damaged in any way, such as: if the power-supply cord or plug is

damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed to

rain or moisture, or if the unit does not operate normally or has been dropped.

iii PJ506EDViewSonic

Declaration of RoHS Compliance

This product has been designed and manufactured in compliance with Directive

2002/95/EC of the European Parliament and the Council on restriction of the use of

certain hazardous substances in electrical and electronic equipment (RoHS Directive)

and is deemed to comply with the maximum concentration values issued by the

European Technical Adaptation Committee (TAC) as shown below:

Substance Proposed Maximum

Concentration Actual Concentration

Lead (Pb) 0.1% < 0.1%

Mercury (Hg) 0.1% < 0.1%

Cadmium (Cd) 0.01% < 0.01%

Hexavalent Chromium (Cr6+) 0.1% < 0.1%

Polybrominated biphenyls (PBB) 0.1% < 0.1%

Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%

Certain components of products as stated above are exempted under the Annex of the

RoHS Directives as noted below:

Examples of exempted components are:

1. Mercury in compact fluorescent lamps not exceeding 5 mg per lamp and in other

lamps not specically mentioned in the Annex of RoHS Directive.

2. Lead in glass of cathode ray tubes, electronic components, fluorescent tubes, and

electronic ceramic parts (e.g. piezoelectronic devices).

3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by

weight or more lead).

4. Lead as an allotting element in steel containing up to 0.35% lead by weight,

aluminium containing up to 0.4% lead by weight and as a cooper alloy containing up

to 4% lead by weight.

iv PJ506EDViewSonic

Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc.

Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of

Microsoft Corporation in the United States and other countries.

ViewSonic, the three birds’ logo, OnView, ViewMatch, and ViewMeter are registered

trademarks of ViewSonic Corporation.

VESA is a registered trademark of the Video Electronics Standards Association. DPMS and

DDC are trademarks of VESA.

PS/2, VGA and XGA are registered trademarks of International Business Machines

Corporation.

Disclaimer:ViewSonic Corporation shall not be liable for technical or editorial errors or

omissions contained herein; nor for incidental or consequential damages resulting from

furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic Corporation reserves the right

to change product specifications without notice. Information in this document may change

without notice.

No part of this document may be copied, reproduced, or transmitted by any means, for any

purpose without prior written permission from ViewSonic Corporation.

Product Registration

To meet your future needs, and to receive any additional product information as it becomes

available, please register your product on the Internet at: www.viewsonic.com. The ViewSonic

Wizard CD-ROM also provides an opportunity for you to print the registration form, which you

may mail or fax to ViewSonic.

For Your Records

Product Name:

Model Number:

Document Number:

Serial Number:

Purchase Date:

PJ506ED

ViewSonic DLP Projector

VS11452

PJ506ED-1_UG_ENG Rev. 1A 03-12-07

The lamp in this product contains mercury.

Please dispose of in accordance with local, state or federal laws.

1 PJ506EDViewSonic

Safety Instructions

Read all of these instructions before you operate your projector and save for future

reference.

1. Check that the operating voltage of your unit is identical with the voltage of your

local power supply.

2. Should any liquid or solid object fall into the cabinet, unplug the unit and have it

checked by the qualied personnel before operating it further.

3. Do not attempt to service this product yourself, as opening or removing covers

may damage the components inside and will void your warranty.

4. Do not place this product on an unstable cart, stand, or table. The product may

fall, causing serious damage to the product.

5. Unplug the unit from the wall socket if it is not to be used for several days. To

disconnect the cord, pull it out by the plug. Never pull the cord itself.

6. The wall socket should be near the unit and easily accessible.

7. Do not place the projector where the cord can be stepped on as this may result

in fraying or damage to the lead or the plug. Be alert to tripping hazards.

8. Never look into the projector lens when the lamp is switched on as the bright light

can damage your eyes. Never let children look into the lens when it is on.

9. Do not place your hand or objects near the ventilation holes. The air coming out

is hot.

10. Never open any covers on the projector except the lamp cover. Dangerous

electrical voltages inside the projector can cause severe injury. Except as

specically directed in this User’s Manual, do not attempt to service this product

yourself. Refer all servicing to qualied service personnel.

11. Unplug the projector from the wall socket before cleaning. Use a damp cloth for

cleaning the projector housing. Do not use liquid or aerosol cleaners.

12. Keep the plastic packing materials (from the projector, accessories and optional

parts) out of the reach of children as these bags may result in death by suffocation.

Be particularly careful around the small children.

2 PJ506EDViewSonic

13. For ventilation reasons, the fan continues to operate after the projector has been

powered off. Please do not unplug the power cord until the fan stops.

14. The projector is equipped with ventilation holes (intake) and ventilation holes

(exhaust). Do not block or place anything near these slots, or internal heat build-

up may occur, causing picture degradation or damage to the projector.

15. When you replace the projector lamp, never touch the new bulb with your bare

hands. The invisible residue left by the oil on your hands may shorten the bulb

life. Use lint-free gloves or nger cots are recommended.

16. The product should be situated away from heat sources such as radiators, heat

registers, stoves, or other products (including ampliers) that produce heat.

17. Do not overload wall outlets, extension cords, or integral convenience receptacles

as this can result in a risk of re or electric shock.

3 PJ506EDViewSonic

Ground

Notes on AC Power Cord

AC Power Cord must meet requirement of country where you use a projector. Conrm

an AC plug type with graphics below and proper AC Power Cord must be used. If

supplied AC Power Cord does not match your AC outlet, contact your sales dealer.

This projector is equipped with a grounding type AC line plug. Make sure that your

outlet ts the plug. Do not defeat the safety purpose of this grounding type plug. We

highly recommend using a video source device also equipped with a grounding type

AC line plug to prevent from signal interference due to voltage uctuation.

4 PJ506EDViewSonic

CONTENTS

Introduction.............................................................................................................5

Projector Features.............................................................................................5

Package Contents.............................................................................................6

Projector Overview............................................................................................7

Using the Product...................................................................................................9

Control Panel.....................................................................................................9

Connection Ports.............................................................................................10

Remote Control ...............................................................................................11

Remote Control Operation ..............................................................................13

Installation.............................................................................................................14

Connecting the Projector.................................................................................14

Powering On/Off the Projector ........................................................................15

Adjusting the Projected Image ........................................................................16

Menu Operation ....................................................................................................19

Image (Computer / Video Mode).....................................................................21

Video (Video Mode).........................................................................................22

Display (Computer Mode) ...............................................................................22

Language (Computer / Video Mode)...............................................................23

Advanced (Computer / Video Mode)...............................................................23

Audio (Computer / Video Mode)......................................................................23

Maintenance..........................................................................................................24

Cleaning the Lens ...........................................................................................24

Cleaning the Projector Housing.......................................................................24

Replacing the Lamp ........................................................................................25

Specications .......................................................................................................27

Appendix ...............................................................................................................28

LED Indicator Messages .................................................................................28

Compatibility Modes........................................................................................29

Troubleshooting...............................................................................................30

5 PJ506EDViewSonic

* means compressed.

Introduction

Projector Features

The projector integrates high-performance optical engine projection and a user-friendly

design to deliver high reliability and ease of use.

The projector offers the following features:

Single chip 0.55” Texas Instruments DLP®technology

SVGA (800 x 600 pixels)

1.1X manual zoom lens

Auto image re-sizing (Auto-Sync.) to 800 x 600 full screen with scaling compression

compatibility for VGA, SVGA, XGA and SXGA*

Compatibility with Macintosh®computers

Compatibility with NTSC, PAL, SECAM, and HDTV

Multi-function remote control

D-Sub 15-pin terminal for analog video connectivity

User-friendly, multi-language on-screen display (OSD)

Advanced electronic keystone correction

Tabla de contenidos

Otros manuales de Proyector de ViewSonic

ViewSonic

ViewSonic PA500S Manual de usuario

ViewSonic

ViewSonic PJ656 - XGA Projector 6.2 Lbs Manual de usuario

ViewSonic

ViewSonic PA504W Series Manual de usuario

ViewSonic

ViewSonic PJD5123 Manual de usuario

ViewSonic

ViewSonic M1 G2 Manual de usuario

ViewSonic

ViewSonic PJL9371 Guía de inicio rápido

ViewSonic

ViewSonic PJD6252L Manual de usuario

ViewSonic

ViewSonic VS16500 Manual de usuario

ViewSonic

ViewSonic PJD7383 Manual de usuario

ViewSonic

ViewSonic PJ402D Manual de usuario

ViewSonic

ViewSonic PRO8450W VS13646 Manual de usuario

ViewSonic

ViewSonic PJD5234 Manual de usuario

ViewSonic

ViewSonic PJ1065 Manual de usuario

ViewSonic

ViewSonic PA700S Manual de usuario

ViewSonic

ViewSonic PJ458D - XGA DLP Projector Manual de usuario

ViewSonic

ViewSonic LS610WH Series Manual de usuario

ViewSonic

ViewSonic PJL3211 VS12417 Manual de usuario

ViewSonic

ViewSonic PJ1158 - XGA LCD Projector Manual de usuario

ViewSonic

ViewSonic PJL6243 Manual de usuario

ViewSonic

ViewSonic PRO9500 Manual de usuario

ViewSonic

ViewSonic PJ751 Manual de usuario

ViewSonic

ViewSonic PJL9371 Manual de usuario

ViewSonic

ViewSonic PJD5353 Manual de usuario

ViewSonic

ViewSonic PJ1158 - XGA LCD Projector Manual de usuario

Manuales populares de Proyector de otras marcas

iEmmet

iEmmet MP-312 Manual de usuario

Epson

Epson VS400 Manual de usuario

Sony

Sony VPL-HS10 Marketing Specifications & Features Manual de usuario

Sony

Sony VPL-HW65ES Manual de servicio

Toshiba

Toshiba TLP-791U Manual de usuario

Philips

Philips LC1341 Guía de referencia

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manual de usuario

NEC

NEC NP600S EDU Manual de usuario

BenQ

BenQ SH753P Manual de usuario

Eiki

Eiki EK-623U series Manual de usuario

Epson

Epson PowerLite Pro Cinema 6020UB Manual de usuario

Epson

Epson PowerLite Home Cinema 705HD Manual de usuario

Christie

Christie LHD700 Manual de usuario

Navitar

Navitar FX Manual de usuario

InFocus

InFocus LitePro 560 Manual de usuario

Sony

Sony SRX-R815P Manual de usuario

Vivitar

Vivitar DP1500 X Manual de usuario

Acer

Acer C20 Series Manual de usuario