ViewSonic LiteBird PJ853 Manual de usuario

User Guide

Guide de l’utilisateur

Bedienungsanleitung

(International Spanish)

(Italian)

(Brazilian Portuguese)

(Swedish)

(Russian)

(Polish)

(Japanese)

(Traditional Chinese)

(Simplified Chinese)

(Korean)

(Arabic)

Image Size 30” – 300”

Super Bright SVGA LCD Projector

LITEBIRD

PJ853-.book Page 1 Wednesday, August 16, 2000 11:41 AM

ViewSonic PJ853 i

Contents

For Your Records ............................................................................1

Getting Started

Package Contents ...........................................................................2

Important Safety Warnings ..............................................................2

Connect Input and Output Devices..................................................3

Installation Steps .............................................................................4

Adjusting the Projector Angle ....................................................5

Projector Placement Distance ...................................................5

Using The Projector

Control Buttons ................................................................................6

OnView Indicators............................................................................8

Setup Main Menu .....................................................................8

Input Menu ...............................................................................9

Image Menu .............................................................................9

Options Menu .........................................................................10

Other Information

Specifications ................................................................................11

Timing Chart ............................................................................12

Troubleshooting .............................................................................13

Power Indicator Lights .............................................................14

Screen Messages ....................................................................14

Maintenance ..................................................................................15

Lamp Replacement .............................................................15

Installing Battery (for remote control) ......................................16

Cleaning Instructions ...............................................................16

Air-Filter ...................................................................................17

Customer Support..........................................................................18

LIMITED WARRANTY

VIEWSONIC Projector ............................................................19

Appendix

Power Cord Safety Guidelines.......................................................20

FCC Information ............................................................................21

PJ853-.book Page i Wednesday, August 16, 2000 11:41 AM

1ViewSonic PJ853

Macintosh, Mac and Power Macintosh are registered trademarks of Apple Computer, Inc.

Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft

Corporation in the United States and other countries.

ViewSonic, the three birds logo and OnView are registered trademarks of ViewSonic Corporation.

VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC

are trademarks of VESA.

ENERGY STAR®is a registered trademark of the U.S. Environmental Protection Agency (EPA).

As an ENERGY STAR®partner, ViewSonic Corporation has determined that this product meets the

ENERGY STAR®guidelines for energy efficiency.

Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions

contained herein; nor for incidental or consequential damagesresulting from furnishing this material,

or the performance or use this product.

In the interest of continuing product improvement, ViewSonic Corporation reserves the right to

change product specifications without notice. Information in this document may change without

notice.

No part of this document may be copied, reproduced, or transmitted by any means, for any purpose

without prior written permission from ViewSonic Corporation.

Electronic WarrantyRegistration

To meet your future needs, and to receive any additional product

information as it becomes available, please register your projector's

warranty on the Internet at:

http://www.viewsonic.com

For Your Records

Product Name:

Model Number:

Document Number

Serial Number:

Purchase Date:

ViewSonic PJ853

VPROJ21732

PJ853_UG_59

_______________

PJ853-.book Page 1 Wednesday, August 16, 2000 11:41 AM

ViewSonic PJ853 2

Getting Started

Congratulations on purchasing a ViewSonic PJ853 LITEBIRD™ LCD projector. Save the original

box and all packing material for future shipping needs.

Package Contents

• ViewSonic PJ853 LITEBIRD LCD Projector

• Remote Control Unit including 3V micro-lithium battery

• Three (3) AC power cords (U.S., European and China)

• Computer video cable (15-pin mini D-sub connector)

• Video cable (RCA connectors)

• Audio mini-stereo cable (RCA connectors)

• User guide

• Carrying Case

Important SafetyWarnings

• Unplug the projector immediately if you detect an abnormal smell or see smoke.

• Do not look directly into the lighted lens; doing so will cause severe eye injury.

•Keep small children away from the projector. Children can be severely burned by the hot lens.

Also, children are more likely to look directly into the lens.

• Never touch the lens or the lamp when hot or warm; doing so will cause a severe burn. Unplug the

projector and allow the unit to cool down for 45 minutes before replacing the lamp or storing the

projector.

• Do not service the unit yourself; doing so could cause injury.

• Do not operate the projector near water or in a humid area. Do not sit drinks on or near the

projector; doing so could cause a burn or short an electrical circuit.

• Do not block the ventilation openings in the projector. Place the projector so that there is adequate

air circulation

• Keep the air filter clean.

• Do not place the projector on a shelf or on any other unstable surface.

Figure 1: Package Contents

PJ853

Power Cord

US Type

Power Cord

Europe Type

RGB Cable

3ViewSonic PJ853

Connect Input and Output Devices

The figure below shows the ports and configurations for connecting external devices to the

ViewSonic PJ853. See “Installation Steps” on page 4.

Figure 2: ViewSonic PJ853 Projector

Figure 3: Connections and Projector Control Buttons

ANDBY/ONINPUTMUTERESET

LAMP

TEMP

POWER

Power Switch

AC Inlet

(to the power cord)

Air Vent

(Intake) Foot Adjuster

Lens

Remote Control Sensor

Projector control

panel

ViewSonic

PJ853

Video IN port Audio IN port

S-video IN port

RGB IN port

Control port

Remote control sensor

Standby/ON

Input

Mute

Reset Lamp indicator

Temperature indicator

Power indicator

Menu button

Air vent

(exhaust)

Speaker

Power Outlet

Power

ON/OFF

Power Cord

ANDBY/ONINPUTMUTERESET

LAMP

TEMP

POWER

PJ853-.book Page 3 Wednesday, August 16, 2000 11:41 AM

ViewSonic PJ853 4

Installation Steps

1Verify Input/Output Connections

Make sure that you have properly connected all input cables before powering on the projector.

2Remove the lens cap.

3Power on the Projector.

•Turn on the Main Power Switch located on the side of the projector. The power indicator will

remain a steady orange. See “Using The Projector” on page 6.

4Press (and hold for 1 second) the Standby/ON button on the projector control pad.

•The power indicator flashes green during warm-up.

•The power indicator will remain a steady green after warm-up. The steady green light indicates

that the ViewSonic PJ853 is ready to use.

•To shut off the lamp – Press the Standby/ON button (and hold for about 3 seconds). The unit

will remain in cool-down mode with the fan on and the orange power LED blinking for 1

minute. The power switch on the side of the projector may be turned off after 1 minute, when

the power light is a steady orange.

5Position the Projector

Make sure that the projector is properly positioned on a level and stable surface. Determine the

distance the projector will be from the screen then adjust the angle of the projection by

positioning the foot adjusters. (See "Adjusting the Projector Angle on page" 5.)

6Power on Input Devices

•Press either the Input button on the projector control pad or the Video/RGB button on the

remote control to select the signal to be projected.

•The selected input signal source displays in the lower right section of the screen.

7Adjust the Focus

Turn the lens ring to adjust the focus

Caution:The projector requires a warm-up period after the power is turned on, and the projector

requires a cool-down period after the power is turned off.

NOTE: The power cannot be turned on for at least 1 minute after the unit has been powered off; this

is a safety feature.

Figure 4: System Setup

Video recorder with S jack

Video recorderDesktop Computer

Notebook Computer

ViewSonic

PJ853

(Note: S-video cable not included)

PJ853-.book Page 4 Wednesday, August 16, 2000 11:41 AM

5ViewSonic PJ853

Adjusting the Projector Angle

Adjust the projection angle using the foot adjusters shown in the illustration. See also KEYSTONE

under "Input Menu on page" 9.

1Press the release button to lower the front foot, then tilt the projector up as shown in Figure 5

below.

•The front foot locks into place when you release the button.

•The front foot adjusts the vertical height of the projected image.

2Rotate the rear foot adjuster to align the image.

The rear foot adjusts the horizontal alignment of the projected image.

Projector Placement Distance

Place the projector on a level table-top or other flat surface. Use the chart in Table 1 below to

determine the optimal placement distance from the screen.

Figure 5: Level Adjustments

Figure 6: Recommended Projector Distances

Table 1: Distance in Inches

Screen Size

(Inches)

a (Inches)

Minimum and Maximum

b (Inches)

40 37 46 3

60 57 69 5

80 77 93 7

100 96 116 9

120 116 139 10

150 145 174 13

200 194 233 17

Rotate the rear

foot adjuster

Press the release button

to lower the front foot adjuster

Front foot adjuster

Top View Side View

ViewSonic PJ853 6

Using The Projector

The control buttons display menus that are explained in detail in the section: “OnView Indicators” on

page 8.

Control Buttons

Press a control button to display a menu then use the arrow buttons to adjust the control. The buttons

on the projector control pad and on the remote control are explained below:

Figure 7: Projector and Remote Controls

Standby/on Button

Press the STANDBY/ON button to begin the warm-up period. The ON indicator

blinks green during warm-up and stays green when the projector is ready to use.

NOTE: The projector cannot be restarted within 60 seconds after it is turned off because

the projector enters a cool-down mode. This is a safety feature.

Input Button (Video and RGB Buttons)

The INPUT button shown is on the projector only. Use the Video and RGB buttons on

the remote control to select the input source.

Press the Input button on the projector to toggle between input sources, computer

(RGB), Composite or S-Video. The remote control has both a Video and an RGB

button.

-Press RGB to select a computer as the input source.

-Press Video to toggle between Composite and S-Video.

Projector control pad

Remote control

PJ853-.book Page 6 Wednesday, August 16, 2000 11:41 AM

7ViewSonic PJ853

Menu Button

The MENU button is a small button on the remote control and the large button on the

projector control pad.

Press the Menu button and then use the up, down, right or left arrowindicators (▲▼)to

display OnView®menus and adjust or select a menu item.

Position Button

The POSITION button is on the remote control only.

Press this button to adjust the position of the screen image. After pressing the

Position button use the up, down, right or left arrow indicators. (▲▼).

-Use the Position button when the input is from a computer (RGB).

NOTE: Position only works on a magnified image.

MagnifyButtons

The MAGNIFY buttons are on the remote control only.

The Magnify buttons are used to zoom in on part of the projected image.

-Use the + button to enlarge the projected image.

-Use the - button to decrease the projected image.

-Use the OFF button to turn off magnification.

Reset Button

The RESET button shown with the arrow and dot icon is on the projector only. The

RESET button on the remote control has no marking but is labeled RESET.

Press the Reset button to restore the factory default settings.

-Use Reset to restore the factory default settings if you have made several

adjustments to the projected image and are not satisfied with the result and

want to start over.

Volume Buttons

The VOLUME buttons are on the remote control only.

Use the Volume buttons to adjust the loudness of the audio signal.

-The up indicator increases the volume.

-The down indicator decreases the volume.

Mute Button

Use the Mute button to temporarily turn off the audio.

BlankButton

The BLANK button is on the remote control only.

Use the Blank button to display a blank screen showing only the background color.

Freeze Button

The FREEZE button is on the remote control only.

Use the Freeze button to freeze (or hold) an image on screen.

PJ853-.book Page 7 Wednesday, August 16, 2000 11:41 AM

ViewSonic PJ853 8

OnView Indicators

Use the OnView®menus shown below to adjust the projected image.

To access and adjust the OnView screens do the following:

1Press the MENU button on the projector control pad or remote control to access on-screen

options and display the SETUP Main Menu.

2Press the ARROW buttons, as explained below, to select and adjust options that are displayed on

the screen.

NOTE: After you have used the ARROW buttons to adjust a value, the value will automatically

apply after a few seconds.

Setup Main Menu

Timer Button

The TIMER button is on the remote control. You can set the timer from the OPTIONS

menu explained in the next section.

Use the Timer button to activate the on-screen timer.

-Press once to display the time on the lower left part of the screen.

-Press again to turn off the display.

Auto Button

Use the Auto button to automatically adjust the vertical position and horizontal

position, phase, and size.

SETUP Main Menu RGB

The setup RGB menu displays 9 adjustment options.

1Press an arrow button (▲▼) to display the menu.

2Press the right or left arrow buttons to select a menu option other than Setup.

3Press the up and down arrow buttonsto move through theSetup menu options.

4After a menu option has been selected, use the right or left arrow buttons to

increase or decrease the value of the selected option.

SETUP Main Menu Video

The Video setup menu displays 8 adjustment options.

1Press an arrow button to display the menu.

2Press the right or left arrow buttons to select a menu option other than Setup.

3Press the up and down arrow buttonsto move through theSetup menu options.

4After a menu option has been selected, use the right or left arrow buttons to

increase or decrease the value of the selected option.

Use the arrow buttons on the projector control pad or on the remote control to

move through the menu options and to increase or decrease the value of a selected

option.

-2

100

800

SETUP INPUT OPT.IMAGE

BRIGHT

CONTRAST

V POSIT

H POSIT

H PHASE

H SIZE

COLOR BAL R

COLOR BAL B

ASPECT

BRIGHT

CONTRAST

SHARPNESS

COLOR

TINT

COLOR BAL R

COLOR BAL B

ASPECT

SETUP INPUT OPT.IMAGE

PJ853-.book Page 8 Wednesday, August 16, 2000 11:41 AM

Tabla de contenidos

Otros manuales de Proyector de ViewSonic

ViewSonic

ViewSonic PG603W Manual de usuario

ViewSonic

ViewSonic PJD5232 Manual de usuario

ViewSonic

ViewSonic PJD5155L Manual de usuario

ViewSonic

ViewSonic VS11580 Guía de inicio rápido

ViewSonic

ViewSonic PJD5134 Manual de usuario

ViewSonic

ViewSonic PJ508D Manual de usuario

ViewSonic

ViewSonic PX700HD Manual de usuario

ViewSonic

ViewSonic PJD6210-WH Manual de usuario

ViewSonic

ViewSonic Office Theater PJL830 Manual de usuario

ViewSonic

ViewSonic PA700WC Manual de usuario

ViewSonic

ViewSonic PJD5352 Manual de usuario

ViewSonic

ViewSonic PJ750 Manual de usuario

ViewSonic

ViewSonic PJ557D - XGA DLP Projector Manual de usuario

ViewSonic

ViewSonic PJ1158-1 Manual de usuario

ViewSonic

ViewSonic PJD5234 Manual de usuario

ViewSonic

ViewSonic PRO8500 Manual de usuario

ViewSonic

ViewSonic PJL802 Manual de usuario

ViewSonic

ViewSonic PX800HD Manual de usuario

ViewSonic

ViewSonic PJD6381 - 2500 Lumens XGA DLP Ultra Short-Throw... Manual de usuario

ViewSonic

ViewSonic PJ557DC Manual de usuario

ViewSonic

ViewSonic PJ503D - DLP Projector Manual de usuario

ViewSonic

ViewSonic PJD7820HD Manual de usuario

ViewSonic

ViewSonic PJD5234 Manual de usuario

ViewSonic

ViewSonic Office Theater PJ1060 Manual de usuario

Manuales populares de Proyector de otras marcas

iEmmet

iEmmet MP-312 Manual de usuario

Epson

Epson VS400 Manual de usuario

Sony

Sony VPL-HS10 Marketing Specifications & Features Manual de usuario

Sony

Sony VPL-HW65ES Manual de servicio

Toshiba

Toshiba TLP-791U Manual de usuario

Philips

Philips LC1341 Guía de referencia

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manual de usuario

NEC

NEC NP600S EDU Manual de usuario

BenQ

BenQ SH753P Manual de usuario

Eiki

Eiki EK-623U series Manual de usuario

Epson

Epson PowerLite Pro Cinema 6020UB Manual de usuario

Epson

Epson PowerLite Home Cinema 705HD Manual de usuario

Christie

Christie LHD700 Manual de usuario

Navitar

Navitar FX Manual de usuario

InFocus

InFocus LitePro 560 Manual de usuario

Sony

Sony SRX-R815P Manual de usuario

Vivitar

Vivitar DP1500 X Manual de usuario

Acer

Acer C20 Series Manual de usuario