Viessmann Vitocell 100-E Guía rápida
Installation and service instructions
for contractors
VIESMANN
Vitocell 100-E
Type SVPA
Heating water buffer cylinder
1500, 2000 l
For applicability, see the last page
VITOCELL 100-E
5672 141 GB 11/2014 Please keep safe.
2
Please follow these safety instructions closely to
prevent accidents and material losses.
Safety instructions explained
!Please note
This symbol warns against the risk of material
losses and environmental pollution.
Note
Details identified by the word "Note" contain additional
information.
Target group
These instructions are exclusively intended for author-
ised contractors.
■Work on electrical equipment must only be carried
out by a qualified electrician.
■The system must be commissioned by the system
installer or a qualified person authorised by the
installer.
Regulations to be observed
■National installation regulations
■Statutory regulations for the prevention of accidents
■Statutory regulations for the protection of the envi-
ronment
■Codes of Practice of the relevant trade associations
■All relevant safety regulations as defined by DIN, EN,
DVGW, VDE and locally applicable standards
aÖNORM, EN and ÖVE
cSEV, SUVA, SVTI, SWKI and SVGW
Working on the system
■Isolate the system from the power supply (e.g. by
removing the separate fuse or by means of a mains
isolator) and check that it is no longer 'live'.
■Safeguard the system against reconnection.
!Please note
Electronic assemblies can be damaged by elec-
trostatic discharge.
Prior to commencing work, touch earthed
objects such as heating or water pipes to dis-
charge static loads.
Repair work
!Please note
Repairing components that fulfil a safety func-
tion can compromise the safe operation of your
system.
Replace faulty components with genuine
Viessmann spare parts.
Auxiliary components, spare and wearing parts
!Please note
Spare and wearing parts that have not been tes-
ted together with the system can compromise its
function. Installing non-authorised components
and making non-approved modifications or con-
versions can compromise safety and may inva-
lidate our warranty.
For replacements, use only original spare parts
supplied or approved by Viessmann.
Safety instructions
Safety instructions
5672 141 GB
3
1. Information Symbols ................................................................................................. 4
Intended use .......................................................................................... 4
Product information ................................................................................ 4
2. Preparing for installation .................................................................................................................. 5
3. Installation sequence Installation .............................................................................................. 6
■Fitting the lower thermal insulation mat and aligning the cylinder ...... 6
■Fitting the thermometer sensor (if supplied) ....................................... 7
■Fitting the 2-part thermal insulation jacket .......................................... 8
■Fitting the cover strips (2-part thermal insulation jacket) .................... 9
■Fitting the 3-part thermal insulation jacket .......................................... 10
■Fitting the cover strips (3-part thermal insulation jacket) .................... 12
■Fitting the cover .................................................................................. 13
■Fitting the cylinder temperature sensor .............................................. 14
■Connections on the heating water side .............................................. 14
4. Parts lists Ordering parts ........................................................................................ 15
Cylinder body ......................................................................................... 16
2-part thermal insulation ........................................................................ 18
3-part thermal insulation ........................................................................ 20
5. Commissioning/service
reports
.................................................................................................................. 22
6. Specification Product characteristics .......................................................................... 23
Index
Index
5672 141 GB
4
Symbol Meaning
Reference to other document containing
further information
Additional information, not safety relevant
1.
Step:
The numbering corresponds to the se-
quence of work.
Intended use
The appliance is only intended to be installed and
operated in sealed unvented systems that comply with
EN 12828 / DIN 1988, or solar thermal systems that
comply with EN 12977, with due attention paid to the
associated installation, service and operating instruc-
tions. DHW cylinders are only designed to store and
heat water of potable water quality. Heating water buf-
fer cylinders are only designed to hold fill water of pot-
able water quality. Only operate solar collectors with
the heat transfer medium approved by the manufac-
turer.
Intended use presupposes that a fixed installation in
conjunction with permissible, system-specific compo-
nents has been carried out.
Commercial or industrial usage for a purpose other
than heating the building or DHW shall be deemed
inappropriate.
Any usage beyond this must be approved by the man-
ufacturer for the individual case.
Incorrect usage or operation of the appliance (e.g. the
appliance being opened by the system user) is prohibi-
ted and results in an exclusion of liability.
Incorrect usage also occurs if the components in the
system are modified from their intended use (e.g.
through direct DHW heating in the collector).
Adhere to statutory regulations, especially concerning
the hygiene of potable water.
Product information
Steel heating water buffer cylinder for storing heating
water in combination with heat pumps, solar thermal
systems, solid fuel boilers and heat recovery.
■Suitable for systems to EN 12828 and DIN 4753.
■Capacity: 1500 or 2000 l
Information
Symbols
5672 141 GB
Information
5
Connections
A
B
Fig. 1 Front
AThermometer sensor retainer
BThermometer (TH)
up to 4 pce (accessories)
A
B
C
D
A
B
C
D
E
F
G
H
Fig. 2 Back
AHeating water flow 1 (HF 1)
BHeating water flow 2 (HF 2)/heating water return
(HR 1)
CHeating water return (HR 2)
DHeating water return (HR 3)
ETR 1*1
FTR 2*1
GTR 3*1
HTR 4*1
Siting
!Please note
To prevent material damage, site the buffer cyl-
inder in a draught-free room free from the risk of
frost.
Otherwise the buffer cylinder will have to be
drained if there is a risk of frost while it is not in
use.
■Provide adequate clearance from the wall so that the
temperature controller can be operated (if installed).
■Placing the cylinder on a plinth will make the room
easier to clean.
■Use the adjustable feet to level the buffer cylinder.
Note
Never extend the adjustable feet beyond a total length
of 30 mm.
*1 Sensor well for thermometer sensor
Preparing for installation
Preparing for installation
5672 141 GB
Installation
6
!Please note
The thermal insulation must not come into con-
tact with naked flames.
Exercise caution when welding and brazing.
Fitting the lower thermal insulation mat and aligning the cylinder
A
B
3.
3x
4.
1.
2.
Fig.3
AType plate
B3 adjustable feet
Insert the adjustable feet into the legs as far as they
will go, then adjust them to level the cylinder.
Note
Never extend the adjustable feet beyond a total length
of 30 mm.
Note
Seal any connections that are not required with red
brass caps.
Installation sequence
Installation
5672 141 GB
Installation
7
Fitting the thermometer sensor (if supplied)
1.
5.
4.
3.
6.
2.
Fig.4
1. Guide the thermometer sensor through the cover
strip and insert the thermometer.
2. Insert 3 of the thermometer sensors into the clamp-
ing bracket as far as they will go and tighten the
wing nut.
3. Pull the sensor retainer from the sensor well.
4. Position the sensor on the outside of the sensor
retainer contact spring so that it is flush with the
front of the spring.
Note
Never wrap insulating tape around the thermometer
sensor.
5. Secure the thermometer sensor lead.
6. Insert the sensor retainer.
Installation sequence
Installation (cont.)
5672 141 GB
Installation
8
Fitting the 2-part thermal insulation jacket
1.
2.
4.
3.
Fig.5
Note
Ensure that no fleece remnants enter the cylinder
through the cylinder connections.
Clip fasteners on each cylinder side:
1500 l: 6 pce
2000 l: 9 pce
Note
This work requires 2 people.
1. At the back of the cylinder: Attach clip fasteners to
the edges of the right and left sections of the insula-
tion jacket. Place the thermal insulation jacket
around the cylinder body.
Note
Leave the clip fasteners in the first notch.
2. At the front of the cylinder: Attach clip fasteners to
the edges of the right and left sections of the insula-
tion jacket.
3. Push the clip fasteners at the back of the cylinder
as close together as they will go.
4. Push the clip fasteners at the front of the cylinder
as close together as they will go.
Installation sequence
Installation (cont.)
5672 141 GB
Installation
9
Fitting the cover strips (2-part thermal insulation jacket)
A
2.
4.
3.
1.
Fig.6
■Fit the thermal insulation jacket evenly around the
cylinder body by patting it.
■Affix type plate A.
Installation sequence
Installation (cont.)
5672 141 GB
Installation
10
Fitting the 3-part thermal insulation jacket
1.
3.
4. 2.
8.
5.
7.
6.
Fig.7
Note
Ensure that no fleece remnants enter the cylinder
through the cylinder connections.
Clip fasteners on each cylinder side:
1500 l: 6 pce
2000 l: 9 pce
Note
This work requires 2 people.
1. Push the thermal insulation jacket (central section)
between the cylinder connections and fit to the cyl-
inder body.
2. Attach clip fasteners to the left edge of the thermal
insulation jacket.
3. Fit the 2nd thermal insulation jacket to the cylinder
body.
4. Connect the two thermal insulation jackets together
using the clip fasteners.
Note
Leave the clip fasteners in the first notch.
5. Attach clip fasteners to the left edge of the 2nd ther-
mal insulation jacket.
6. Fit the next thermal insulation jacket to the cylinder
body.
Installation sequence
Installation (cont.)
5672 141 GB
Installation
Otros manuales para Vitocell 100-E
8
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Calentador de agua de Viessmann
Viessmann
Viessmann VITOCELL 100-B Instrucciones de funcionamiento
Viessmann
Viessmann VITOCELL 300B Manual de usuario
Viessmann
Viessmann Vitocell 100-B CVB Series Manual de usuario
Viessmann
Viessmann Vitocell 100 CHA Series Guía
Viessmann
Viessmann VITOCELL-V 100 Manual de funcionamiento original
Viessmann
Viessmann VITOCELL 100-V Manual de usuario
Viessmann
Viessmann VITOTHERM EI5 Series Manual de usuario
Viessmann
Viessmann OpenTherm Instrucciones de funcionamiento
Viessmann
Viessmann Vitocell 100-E Guía rápida
Viessmann
Viessmann Vitocell 100-E Guía rápida
Viessmann
Viessmann Vitocell 100-E Guía rápida
Viessmann
Viessmann VITOCELL 300B Guía rápida
Viessmann
Viessmann VITOCELL 300V Manual de usuario
Viessmann
Viessmann VITOCELL-V 100 Manual de usuario
Viessmann
Viessmann VITOTHERM EI5 Series Guía rápida
Viessmann
Viessmann VITOCELL 300 EVI Series Manual de usuario
Viessmann
Viessmann Vitocell 100 Instrucciones de funcionamiento
Viessmann
Viessmann Vitocell 140-E Guía rápida
Viessmann
Viessmann VITOCELL-H 300 Manual de usuario
Viessmann
Viessmann VITOCELL 100-B Manual de usuario
