Videofied XL GPRS Manual de usuario
XL GPRS Control Panel
INSTALLATION MANUAL
www.videofied.com
Doc. - Ref. 230-XL
Last modification date : November 2013
Firmware version : XLP.03.91.XX.XXX and later
Description
The XL control panel is a Videofied wireless alarm system operated by battery or mains power supply. This
panel is intended mainly for residential and commercial markets. With theMotion Viewers™andVideofied®
range of products, the XL panel provides video verification in case of intrusion.
The XL panel is a standalone alarm system with an integrated GPRS / GSM communicator for connection to a
central station. The panel also features a 105 dB integrated siren, a built-in intercom for audio challenge and
a backlighted touchpad with an integrated badge reader.
Wireless Technology
The XL GPRS, along with all Videofied devices, uses the patented S2View®, Interactive, AES Encrypted
Wireless technology, providing optimum signal integrity and security.
The bi-directional RF communication path between all devices and the system control panel guarantees high
signal reliability. Integrated antennas eliminate protruding wires or rods, both more difficult to install and
unsightly to consumers, and potentially troublesome if damaged.
The panel supervises every device (excluding the remote key fob) to validate current open/close state,
tamper condition, serial number, date of manufacture, firmware revision, and battery status.
The RSI VIDEO TECHNOLOGIES team wishes you a good installation.
Siren and Speakers
Touchpad Badge Reader
Microphone
Locking Screw
www.videofied.com
INSTALLATION MANUAL
2
Introduction
www.videofied.com
INSTALLATION MANUAL
3
Summary
Introduction....................................................................................................2
Summary..........................................................................................................3
1. XL Panel Setup..................................................................................................4
1.1 XL Panel Setup.................................................................................................................4
1.2 SIM Card Installation...........................................................................................4
1.3 XL Assembly....................................................................................................4
1.4 Powering and Initialization...................................................................................5
1.5 Pairing the remote keypad................................................................................................5
2. XL Panel Programming.......................................................................................6
3. XL Features Guide.............................................................................................13
3.1 Get to Access level 4.....................................................................................................13
3.2 How to Arm/Disarm the System........................................................................................13
3.3 Arming and Siren Mode Configuration.............................................................................14
3.4 Pairing a new keypad without opening the panel.................................................................14
3.5 Manage badges and access codes....................................................................................15
3.6 Delete the keypad or any other device..........................................................................17
3.7 Read the events log..........................................................................................................18
3.8 Opening the cover of an installed panel...............................................................................18
3.9 Golden rules.......................................................................................................................18
4. Transmitted Events List......................................................................................19
5. 2G3G Error Codes.............................................................................................20
6. Numeric Touchpad.............................................................................................21
7. Technical Specifications and Security Notes........................................................22
1.1 XL Panel Setup
Open the box and remove the cardboard
mounting template sitting on top. Place the
template on the wall with the arrow pointing
upward.
Mark the 5 screw points on the wall and drill pilot
holes for wall anchors. Install wall anchors, then
attach base of control panel to wall.
XL panel is provided with a reinforcement brace
kit including 4 velco straps. Insert the 4 straps in
the back casing, then mount the casing on the
wall. (The EN50131 standard requires the installation
of this brace kit).
A screw must be used in the tamper protection
hole for the panel wall tamper to function
correctly.
Insert the Alkaline D type batteries as shown;
ensuring the polarity matches the labeling on the
inside of the battery cover.
Bracket holes
Before removing the front cover from its box,
put the SIM card on the plastic base (Take care
to respect the right direction).
DO NOT insert or remove the SIM card while the
panel is powered.
1.2 SIM Card Installation
1.3 XL Assembly
Connect the panel’s face to its base by carefully
placing the hinges on it.
2 locking clips are provided to strengthen
the hinges: position each locking clip before
locking them completely (The EN50131 standard
requires the installation of these locking clips).
Tamper bracket hole
Mandatory to trigger tamper alarm.
Locking clips location
www.videofied.com
INSTALLATION MANUAL
4
1. XL Panel Setup
1.4 Powering and Initialization
• The panel is powered by a mains power supply with 4 LR20 alkaline backup batteries (Option 1 recommended) or by 8 LR20 alkaline
batteries (Option 2). When the panel is powered, it will beep and the built-in keypad should start flashing.
• Press and hold the PROGRAMMING BUTTON for 10 seconds, until the panel beep again and thepanel’s keypad lights up.
• The panel is now reset, a CMA, XMA or XMB has to be enrolled to configure the panel.
Mains Connector
Programming Button
Batteries connector
Option 1
Option 2
THE CONTROL PANEL MUST BE CONNECTED TO AN EXTERNAL POWER SUPPLY (OPTION 1)
WHEN USING THE RINGTONE FEATURE OR SMARTPHONE APP.
www.videofied.com
INSTALLATION MANUAL
5
1. XL Panel Setup
• Press briefly the XL programming button and release for
the enrollment of a programming keypad. The display
should start spinning.
• Insert all LS14500 Lithium batteries into the keypad.
• Do not mount the keypad. It will display one of the
following screens:
1.5 Pairing the remote keypad
RSI (c) 2013
videoed.com <=========XX=========>
or
• Press on both
CLR
and
ESC NO
keys at the same time
and release. The indicator LED on the keypad will blink
rapidly. Wait for the keypad to pair.
• If the keypad doesn’t pair up with the panel and
shows «XX», it certainly means that it is still paired to
another system and needs to be reset. Take the batteries
out, and press repeatedly on the keypad tamper switch.
Then proceed to the above steps.
www.videofied.com
INSTALLATION MANUAL
6
1. XL Panel Setup
Keypad Display Actions and comments
KEYPAD 1
RECORDED
RADIO RANGE TEST?
RF TEST
x/9
RF TEST
9/9
RADIO RANGE TEST?
INSTALLER CODE
4 TO 6 DIGITS
THEN OK/YES
INSTALLER CODE :
< - LANGUAGE : - >
ENGLISH (UK)
The system can also be programmed in: french, italian,
german, dutch, spanish, swedish, portuguese, danish,
czech and polish.
The language can be changed at any time once the panel
is programmed in the MAINTENANCE menu.
The Radio Range test must be run during the device
learning process in order to ensure proper pairing with
the control panel. This test measures the strength of
communication between the device and the control
panel. The keypad will display a real time radio range
value on a scale of 9.
To receive the most accurate results you must run the
radio range test for at least 30 seconds.
Result must be 8 out of 9 or better for reliable
transmission.
Using the Alphanumeric Keypad, enter the Installer Code
of your choice.
The Installer Code will be used for all future maintenance
and configuration.
This code is important to keep track of.
There is no back door or Default codes to the
system.
Please refer to the restriction rule for codes (Chapter 3.5).
Some codes are already used by default and therefore
cannot be used.
OK or YES
OK or YES
Please wait
OK or YES
ESC
NO
for language selection
OK or YES
CONFIRM CODE
OK or YES
OK or YES
www.videofied.com
INSTALLATION MANUAL
7
2. XL Panel Programming
Keypad display Actions and comments
CODE NAME :
OK or YES
ACCESS 1
REGISTERED
You may name the installer code using the Alphanumeric
Keypad.
If using automatic setting (called installer default list),
enter the name of the list.
Warning : If the wrong installers list name is used it
cannot be set later, the system must be defaulted.
Leaving the name blank by pressing
ESC NO
, it will be
named ‘ACCESS 1’ by default.
Please wait
ADJUSTING DATE
AND TIME
DATE (YEAR):
12/ /
To set the year
OK or YES
DATE (MONTH):
13/01/
To set the month
OK or YES
You may proceed in the same way for:
Day, Hour and Minutes.
13/10/14 10:47
ENTRY COMPLETE !
ACCOUNT NUMBER :
CONNECTED TO
MONITOR. STATION?
OK or YES
Use the Alphanumeric Keypad to enter in a 4-8 digit
account number provided by the Central Station.
ACCOUNT NUMBER :
567001
OK or YES
ESC
NO
www.videofied.com
INSTALLATION MANUAL
8
2. XL Panel Programming
TEST (hour) :
04:
CODE/STATE
MODIFICATION?
Test Periodicity: 1 hour, 12 hours, 24 hours, 48 hours, 7
days or no tests.
We suggest a 24 hours periodic test call.
PERIODIC TEST
PERIODE DE TEST :
24 HOURS
To select periodicity
OK or YES
OK or YES
TEST (minutes) :
04:15
OK or YES
ESC
NO
OK or YES
CODE/STATE
MODIFICATION
OK or YES
Events list
ESC
NO
CODE/STATE
MODIFICATION
ESC
NO
SERVER
ADRESSES ?
The CODE/STATE MODIF. menu is to configure the
transmitted events to the monitoring station, use the
arrow keys to toggle between events and
OK or YES
to
modify.
ALARM: event transmitted upon occurrence.
ALARM/END: event is transmitted on occurrence and
on event restoral.
NOT TRANSMITTED: event is not transmitted, however
it will appear on the keypad.
Please liaise with your Monitoring Station to ensure
that the requested events to transmit are correctly
set.
Keypad display Actions and comments
OK or YES
www.videofied.com
INSTALLATION MANUAL
9
2. XL Panel Programming
IP1 ADDRESS
0.0.0.0
DOMAIN NAME 1 PORT 1
888
SERVER
ADRESSES ?
SERVER
ADRESSES ?
OK or YES
ESC
NO
ESC
NO
OK or YES
APN CODE
internet-entrepr
USER NAME
orange
PASSWORD
orange
The APN Code (Access Point Name), User Name and Password are supplied by the
mobile operator. Please make sure you have entered the code exactly as indicated by your
local SIM card operator.
Press
OK or YES
to enter/modify the parameter then
OK or YES
for validation.
Note: When entering your SIM card settings, both APN codes, username and password
fields are case sensitive! It makes a difference between UPPER and lower case letters.
To switch between UPPER and lower case, use the M/m key from CMA keypad or hold a
digit key (0-9) for XMA/XMB.
ESC
NO
ESC
NO
The IP1 address, Domain name 1 and/or Port 1 are provided by the monitoring station.
Leave Port details at 888 unless otherwise instructed.
Press
OK or YES
to enter/modify the parameter then
OK or YES
for validation.
WARNING : You will use either an IP adress or a Domain name but not both, leave the
Domain name blank if an IP adress has already been entered.
Press on the right arrow to configure IP/Domain name 2 and PORT2 (for the back-up server),
and IP/Domain name TMT and PORT TMT (to configure remote maintenance server).
www.videofied.com
INSTALLATION MANUAL
10
2G3G
PARAMETERS?
2G3G
PARAMETERS?
2G3G LEVEL ?
2. XL Panel Programming
Otros manuales para XL GPRS
1
Tabla de contenidos
Otros manuales de Panel de control de Videofied
Videofied
Videofied DSC PC1616 Series Guía de inicio rápido
Videofied
Videofied XT200i Manual de usuario
Videofied
Videofied XTO 210 Manual
Videofied
Videofied XV 210 Manual de usuario
Videofied
Videofied XT-iP 620 Guía del usuario
Videofied
Videofied XT-IP 630 Manual del propietario
Videofied
Videofied XT 620 Manual
Videofied
Videofied XV-iP 210 Manual de usuario
Videofied
Videofied XT-iP 210 Manual de usuario
Videofied
Videofied XT 210 Manual
