Viavi OSA-4100 Manual de usuario

VIAVI//Public

T-BERD/MTS 2000 Handheld Modular Test Set

T-BERD/MTS-2000 Handheld Modular Test Set

QUICK CARD

►Use the VIAVI P5000i or FiberChek Probe

microscope to inspect both sides of every

connection being used (Nano OSA Port,

Launch Cable, bulkhead connectors, patch

cables, etc.)

►Focus fiber on the screen. If dirty, clean the

end-face.

►If it appears clean, run inspection test.

►If it fails, clean the fiber and re-run inspection

test. Repeat until it passes.

4100-series Nano OSA

This quick card describes how to connect to a fiber under test, configure test setups, run

tests, and analyze results with a T-BERD/MTS-2000 equipped with a Nano OSA module.

EQUIPMENT REQUIREMENTS

FIBER INSPECTION GUIDELINES

►T-BERD/MTS 2000 equipped with the

following:

•Fiber Optics Software Release V21.14 or

greater

•Nano OSA Module

(OCV-4100 or OSA-4100 )

•Fiber optic cleaning and inspection tools

►Fiber optic patch cable or Launch Cable

►Optical Coupler to connect patch cable to

Fiber Under Test

Figure 2: Inspect Before You Connect

Figure 1: Equipment Requirements

VIAVI//Public

T-BERD/MTS 2000 Handheld Modular Test Set

T-BERD/MTS-2000 Handheld Modular Test Set

QUICK CARD

CONNECT TO FIBER UNDER TEST (FUT)

All fibers and connectors should be cleaned and inspected prior to connection, as described on page 1.

The Nano OSA is typically connected to the FUT via a Monitor Port or splitter/tap to not disrupt service.

The Nano OSA can also be directly connected to the common port or common fiber via a coupler during

turn up or maintenance:

1. Inspect the Nano OSA port on top of the test set.

2. If connecting to the Common Cable, connect the Common

Cable to an optical coupler with the same connector type and

inspect the fiber end face in the coupler.

3. If connecting to the Monitor Port or Common Port on the Mux,

inspect the Mux Port.

4. Inspect the fiber end face of the Patch Cable and connect the

cable to the Nano OSA port.

5. Inspect the other fiber end face of the Patch Cable and Connect

the Launch Cable to the coupler or Mux port.

Figure 3: OTDR Port Inspection

Figure 4: Connecting to Monitor Port

Figure 5: Connecting to Common Cable

VIAVI//Public

T-BERD/MTS 2000 Handheld Modular Test Set

T-BERD/MTS-2000 Handheld Modular Test Set

QUICK CARD

VERIFY SETUP

LAUNCH TEST

1. Press the ON/OFF button to start the

test set.

2. Press the Home button to display

the Home view with the Optical Spectrum

icon.

3. Tap the Optical Spectrum icon

until it is yellow and highlighted.

Figure 6: Home Screen

1. Tap Setup icon

2. Tap each setup category and verify they

match as shown below.

Note: The below shows the default setup

for standard use of the Nano OSA. User

typically does not need to change any

settings for running a sweep of channels.

Figure 7: Setup Menu

VIAVI//Public

T-BERD/MTS 2000 Handheld Modular Test Set

T-BERD/MTS-2000 Handheld Modular Test Set

QUICK CARD

Product specifications and descriptions in this

document are subject to change without notice.

Patented as described at viavisolutions.com/patents

To reach the VIAVI office nearest you,

visit viavisolutions.com/contact

+1 844 GO VIAVI

(+1 844 468-4284)

RUN SWEEP TEST

3. Tap START icon (upper right) to run scan

4. View Results after scan completes (use your finger or stylus to scroll up/down as needed)

Total # of

Channels

detected

Verifies Channels &

Power Levels (dBm) Measures offset

(detect optics going bad)

Measures

Actual

wavelengths

Otros manuales para OSA-4100

Este manual sirve para los siguientes modelos

Otros manuales de Equipo de prueba de Viavi

Viavi

Viavi Parent Guide Manual de usuario

Viavi

Viavi OneAdvisor 1000 Manual de usuario

Viavi

Viavi SmartClass OLP-85 Series Manual de usuario

Viavi

Viavi E4100 Series Manual de lista de piezas

Viavi

Viavi SmartClass Fiber OLTS-85 Manual de usuario

Viavi

Viavi T-BERD/MTS 5800 Manual de usuario

Viavi

Viavi NSC-200 Manual de usuario

Viavi

Viavi FIT-82P03 Manual de usuario

Viavi

Viavi Seeker X with MCA III Manual de usuario

Viavi

Viavi OneAdvisor 800 Series Manual de usuario

Viavi

Viavi HST-3000 Manual de usuario

Viavi

Viavi ComXpert CX100 Manual de usuario

Viavi

Viavi T-BERD/MTS 2000 Manual de usuario

Viavi

Viavi T-BERD/MTS 4000 Manual de usuario

Viavi

Viavi OneAdvisor 1000 Manual de usuario

Viavi

Viavi T-BERD/MTS-2000 Manual de lista de piezas

Viavi

Viavi RGS-2000NG Manual de usuario

Viavi

Viavi IFR 6000 Manual de usuario

Viavi

Viavi AVX-10K Manual de usuario

Viavi

Viavi PSD90-3 Manual de usuario

Viavi

Viavi NSC-100 Manual de usuario

Viavi

Viavi T-BERD/MTS-5800 Manual de lista de piezas

Viavi

Viavi T-BERD MTS 5800 Manual de lista de piezas

Viavi

Viavi CT-X Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario