VIA Technologies AMOS-825 Manual de usuario

1.00-04052017-151700

QUICK START GUIDE

AMOS-825

Android EVK v4.0.4

No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language,

in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise without the prior written

permission of VIA Technologies, Incorporated.

Trademarks

All brands, product names, company names, trademarks and service marks are the property of their respective holders.

Disclaimer

VIA Technologies makes no warranties, implied or otherwise, in regard to this document and to the products described in this

document. The information provided in this document is believed to be accurate and reliable as of the publication date of this

document. However, VIA Technologies assumes no responsibility for the use or misuse of the information (including use or

connection of extra device/equipment/add-on card) in this document and for any patent infringements that may arise from the use of

this document. The information and product specifications within this document are subject to change at any time, without notice

and without obligation to notify any person of such change.

VIA Technologies, Inc. reserves the right the make changes to the products described in this manual at any time without prior notice.

AMOS-825 Android EVK v4.0.4 Quick Start Guide

iii

Revision History

Version Date Remarks

1.0 04/05/2017

Initial release

AMOS-825 Android EVK v4.0.4 Quick Start Guide

Table of Contents

1. Introduction ................................................................................................................................... 1

Package Contents ................................................................................................................... 1

1.1.

Firmware Folder Contents ............................................................................................ 1

1.1.1.

Document Folder Contents.......................................................................................... 1

1.1.2.

Tools Folder Contents .................................................................................................. 1

1.1.3.

Version Information and Supported Features .................................................................. 2

1.2.

2. Image Installation ......................................................................................................................... 3

Booting from the SPI ROM with an eMMC ....................................................................... 3

2.1.

3. Hardware Functions ..................................................................................................................... 5

Setting Up U-Boot Parameters ............................................................................................ 5

3.1.

Restoring Default U-Boot Parameters................................................................................ 6

3.2.

Using the Android Console ................................................................................................. 6

3.3.

Configuring the Wi-Fi & Bluetooth .................................................................................... 7

3.4.

Connecting to the Internet ........................................................................................... 7

3.4.1.

Enabling Bluetooth ........................................................................................................ 7

3.4.2.

3.4.2.1. Using the Bluetooth A2DP Profile ..................................................................... 7

3.4.2.2. Using the Bluetooth SPP Profile ......................................................................... 8

Enabling GPS ........................................................................................................................ 10

3.5.

Smart ETK .............................................................................................................................. 11

3.6.

Testing WatchDog Timer Function ........................................................................... 12

3.6.1.

Testing FlexCAN Function .......................................................................................... 13

3.6.2.

4. Accessories .................................................................................................................................. 16

Configuring the EMIO-2550 miniPCIe Mobile Broadband Module .......................... 16

4.1.

AMOS-825 Android EVK v4.0.4 Quick Start Guide

1. Introduction

This Quick Start Guide explains how to boot the Android EVK system image on the AMOS-

825 system in order to begin evaluating the platform.

The AMOS-825 Android EVK v4.0.4 is developed based on the NXP android_l5.0.0_1.0.0-

ga (Android 5.0 Lollipop) and enables the hardware features of the AMOS-825 system.

Package Contents

1.1.

There are three folders in the package as listed below.

Firmware folder Description

Images_autoinstall_sd.zip Android EVK system image and installation script

files

Document folder Description

AMOS-825_Android_EVK_v4.0.4_Quick_Start_

Guide_v1.00_20170405.pdf Quick start guide

Tools folder Description

AMOS-825_Smart_ETK_Demo_v0.0.16.apk SmartETK demo program

BluetoothSPPTest.apk Bluetooth SPP profile demo program

AMOS-825 Android EVK contents

Firmware Folder Contents

1.1.1.

Images_autoinstall_sd.zip: The Android EVK system image and installation script files.

Document Folder Contents

1.1.2.

AMOS-825_Android_EVK_v4.0.4_Quick_Start_Guide_v1.00_20170405.pdf: The Quick

Start Guide explains how to boot the Android EVK system image on the AMOS-825 system

in order to begin evaluating the platform.

Tools Folder Contents

1.1.3.

AMOS-825_Smart_ETK_Demo_v0.0.16.apk: is the demo program of the Smart ETK.

BluetoothSPPTest.apk: is the demo program of the Bluetooth SPP profile.

AMOS-825 Android EVK v4.0.4 Quick Start Guide

Version Information and Supported Features

1.2.

•U-Boot version: 2014.04

•Kernel version: 3.10.53

•Evaluation image: Android Lollipop 5.0

•Development based on NXP android_l5.0.0_1.0.0-ga (Android 5.0 Lollipop)

•Supports SPI with eMMC boot

•Supports 7” Projective capacitive touch monitor (800 x 480) (through I2C

interface)

•Supports COM as debug port

•Supports 2 FlexCAN TX/RX

•Supports Gigabit Ethernet

•Supports Line-out and Mic-in

•Supports IEEE 802.11b/g/n Wi-Fi

•Supports Bluetooth 4.0

oA2DP and SPP profile

•Supports U-blox MAX-7 GPS/GNSS module

•Supports EMIO-2550 miniPCIe Mobile Broadband module

•Supports Smart ETK v0.0.16: Watchdog Timer, CAN Bus

•Supports OTA (Over-the-Air technology)

•Supports shutdown option in Quick Settings

•Supports Ethernet configuration in Settings

AMOS-825 Android EVK v4.0.4 Quick Start Guide

2. Image Installation

The AMOS-825 Android system only provides booting from the SPI ROM with an eMMC.

This section explains the setup requirements for booting from the SPI ROM with an eMMC.

A precompiled image is provided in the “Firmware” folder of the EVK.

Booting from the SPI ROM with an eMMC

2.1.

The Images_autoinstall_sd.zip includes the Android EVK system image and the installation

scripts files.

The first step is to extract Images_autoinstall_sd.zip file to make the bootable Micro SD card.

Insert a card into your Linux host machine and make sure it is not mounted. Open the

terminal on your host machine, and run the script mk_install_sd.sh as shown below,

replacing <device name> with the correct value for the card, for example “sdb”.

Important: Make sure you are writing to the correct device or the host system environment

could be damaged.

$ sudo ./mk_install_sd.sh /dev/<device name>

Next, on the AMOS-825, set the Micro SD/SPI boot switch to the Micro SD position shown

below.

Micro SD/SPI boot switch diagram

Insert the prepared Micro SD card into the AMOS-825, connect an LVDS display, and

power on the AMOS-825 to initiate the boot process. When the boot process is completed,

you will see the command line of Linux environment.

AMOS-825 Android EVK v4.0.4 Quick Start Guide

To install the U-Boot and Android EVK image into SPI ROM and eMMC, use the following

command:

$ ./fsl-eMMC-partition.sh –f imx6q /dev/mmcblk0

In order to boot from the SPI ROM make sure the Micro SD/SPI boot switch is set to SPI

ROM boot.

Micro SD/SPI boot switch diagram

Next, power on the device to initiate the boot process. When the boot process is

completed, you will see the Android desktop.

AMOS-825 Android EVK v4.0.4 Quick Start Guide

3. Hardware Functions

Setting Up U-Boot Parameters

3.1.

The first step is to connect the host machine and the AMOS-825 through the COM port.

Use a serial port communication program such as PuTTY, GtkTerm, or Minicom, to configure

the serial port setting and connect to the debug console. There you will be able to see the

U-Boot boot log and adjust settings in the U-Boot console.

+--------------------------------------------------------------+

| A - Serial Device : /dev/ttymxc0 |

| B - Lockfile Location : /var/lock |

| C - Callin Program : |

| D - Callout Program : |

| E - Bps/Par/Bits : 115200 8N1 |

| F - Hardware Flow Control : No |

| G - Software Flow Control : No |

+--------------------------------------------------------------+

Serial port setting of host machine

COM port diagram

Next, power on the AMOS-825 system to initiate the boot process. When prompted, press

any key to stop the boot process, and enter the U-Boot console as illustrated by the

screenshot below.

U-Boot 2014.04 (May 31 2016 - 18:49:13)AMOS825 ver:4.0.4

CPU: Freescale i.MX6Q rev1.2 at 996 MHz

CPU: Temperature 30 C, calibration data: 0x5894f169

Reset cause: POR

Board: iMX6Q-VAB820

I2C: ready

DRAM: 1 GiB

MMC: FSL_SDHC: 0, FSL_SDHC: 1

SF: Detected W25Q32BV with page size 256 Bytes, erase size 4 KiB,

total 4 MiB

*** Warning - bad CRC, using default environment

No panel detected: default to Hannstar-XGA

Display: Hannstar-XGA (1024x768)

In: serial

Out: serial

Err: serial

Net: FEC [PRIME]

Warning: failed to set MAC address

Normal Boot

Hit any key to stop autoboot: 0

AMOS-825 Android EVK v4.0.4 Quick Start Guide

Debug console view of boot process

To list the current U-Boot parameters, use the following command:

=> printenv

Make sure the printout message is as follows:

=> printenv

baudrate=115200

boot_emmc_root=mmc dev ${root_media_uboot};ext2load mmc

${root_media_uboot}:${root_partition} ${loadaddr} uImage;ext2load mmc

${root_media_uboot}:${root_partition} ${dtbaddr} imx6q-vab820.dtb;bootm ${loadaddr} -

${dtbaddr};

boot_media=booti mmc1

Restoring Default U-Boot Parameters

3.2.

If the U-Boot parameters have been modified, the “destroyenv” command in the U-Boot

console can restore the factory default settings. To restart the device, use the “reset”

command.

=> destroyenv

=> saveenv

=> reset

Using the Android Console

3.3.

The first step is to connect the host machine and the AMOS-825 through the COM port.

Use a serial port communication program such as PuTTY, GtkTerm, or Minicom, to connect

to the debug console. There you will be able to see the U-Boot boot log and adjust

settings in the U-Boot console. Next, power on the AMOS-825 to initiate the boot process.

When the boot process is completed, you will automatically log in to an Android console.

root@AMOS-825:/ #

Otros manuales para AMOS-825

Tabla de contenidos

Otros manuales de PC industrial de VIA Technologies

VIA Technologies

VIA Technologies AMOS-5210 Manual de usuario

VIA Technologies

VIA Technologies AMOS-820-QP SKU Manual de usuario

VIA Technologies

VIA Technologies AMOS-3003 Manual de usuario

VIA Technologies

VIA Technologies EPIA-P910 Manual de usuario

VIA Technologies

VIA Technologies AMOS-820 SKU Manual de usuario

VIA Technologies

VIA Technologies AMOS-3005 Manual de usuario

VIA Technologies

VIA Technologies AMOS-3006 Manual de usuario

VIA Technologies

VIA Technologies AMOS-3007 Manual de usuario

VIA Technologies

VIA Technologies AMOS-825 Manual de usuario

VIA Technologies

VIA Technologies ART-3000 Manual de usuario

VIA Technologies

VIA Technologies ART-3000 Manual de usuario

VIA Technologies

VIA Technologies AMOS-5002 Manual de usuario

VIA Technologies

VIA Technologies AMOS-3000 Manual de usuario

Manuales populares de PC industrial de otras marcas

Chipsee

Chipsee PPC-A72-101 Manual de usuario

Advantech

Advantech UNO-2184G Manual de usuario

MSI

MSI MS-9A76 Manual de usuario

Stackrack

Stackrack THOR200 Manual de usuario

Moxa Technologies

Moxa Technologies DA-682C Series Manual de usuario

Nodka

Nodka eBOX-3000-ETC Manual de usuario

Siemens

Siemens SIMATIC IPC627E Manual de usuario

MSI

MSI MS-9A89 Manual de usuario

Artila

Artila Matrix-516 Manual de usuario

Siemens

Siemens SIMATIC Rack PC 840 V2 Manual de usuario

Advantech

Advantech IPPC-6152A Manual de usuario

Beckhoff

Beckhoff CX9020 Manual de usuario

Dell

Dell Embedded Box PC 5000 Manual de usuario

IBASE Technology

IBASE Technology ASB200-918 Series Manual de usuario

Lenovo

Lenovo ThinkCentre M90q Manual del propietario

IXXAT

IXXAT Econ 100 Manual de usuario

Kontron

Kontron KBox A-151-TGL Manual de usuario

AXIOMTEK

AXIOMTEK ICO500-518 Series Manual de usuario