VEVOR M1H-ZP5-254D-1 Manual de usuario
M1H-ZP5-254D-1
USER MANUAL
BENCH-TYPE CIRCULAR SAW
Have product questions? Need technical suppo? Please feel free to contact us:
CustomerSe[email protected]
NEED HELP? CONTACTUS!
This is the original instruction, please read all manual instructions carefully before
operating. VEVOR resees a clear interpretation of our user manual. The appear-
ance of the product shall be subject to the product you received. Please forgive us
that we won't inform you again if there are any technology or software updates
on our product.
Bench-Type
Circular Saw
01
02
SAFETY INSTRUCTION
Warning - To reduce the risk of inju, user must read instructions
manual carefully .
Danger! Read all safety regulations and instructions.
Keep all safety regulations and instructions in a safe place for future use.
This product is of protection class II. That means it is equipped
with enhanced or double insulation.
The product complies with the applicable European directives and
an evaluation method of conformity for these directives was done.
Caution! Wear a breathing mask. Dust which is injurious to health
can be generated when working on wood and other materials.
Never use the device to work on any materials containing asbestos!
Caution! Wear ear-mus. The impact of noise can cause damage
to hearing
Caution! Wear safety goggles. Sparks generated during working or
splinters, chips and dust emitted by the device can cause loss of
sight.
This symbol, placed before a safety comment, indicates a kind of
precaution, warning, or danger. Ignoring this warning may lead to
an accident. To reduce the risk of inju, re, or electrocution,
please always follow the recommendation shown below.
Caution! Risk of inju! Do not reach into the running saw blade.
03
1) Work area safety
a) Keep work area clean and well-lit. Cluttere and dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of
ammable liquids, gases or dust. Power tools create sparks that may ignite dust or
fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can
cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with eahed (grounded) power tools. Unmodied plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with eahed or grounded suaces such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is
eahed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for caring, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving pas. Damaged
or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. The use a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current
device (RCD) protected supply. The use of an RCD reduces the risk of electric shock.
WARNING! Read all safety warnings instructions, illustrations and speci-
cations provided with this power tool. Failure to follow the warnings and instruc-
tions may result in electric shock, re and/or serious inju. The term "power tool" in
the warnings refers to your mains-operated (corded) power tool or batte-operated
(cordless) power tool.
Save all warnings and instructions for future reference.
GENERAL SAFETY REGULATIONS
04
3) Personal safety
a) Stay ale, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the inuence of
drugs, alcohol or medication. A moment of inattention while operating power tools
may result in serious personal inju.
b) Use safety equipment. Always wear eye protection. Safety equipment such as
dust mask, non-skid safety shoes, hard hats, or hearing protection
used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional staing. Ensure the switch is in the o-position before
connecting to power source and/or batte pack, picking up or caring the tool.
Caring power tools with your nger on the switch or energizing power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench
or a key left attached to a rotating pa of the power tool may result in personal
inju.
e) Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelle. Keep your hair, clothing
and gloves away from moving pas. Loose clothes, jewelle or long hair can be
caught in moving pas.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of these devices can
reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools allow you to become
complacent and ignore tool safety principles. A careless action can
cause severe inju within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn on and o. Any power tool
that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source before making any adjustments,
changing accessories, or storing power tools. Such preventive safety measures
reduce the risk of staing the power tool accidentally.
05
ADDITIONAL SAFETY INSTRUCTIONS FOR TABLE SAWS
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving pas, break-
age of pas and any other condition that may aect the power tools operation. If
damaged, have the power tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits,etc., in accordance with these
instructions and in the manner intended for the paicular type of power tool, taking
into account the working conditions and the work to be peormed. Use of
the power tool for operations dierent from intended could result in a hazardous
situation. Slippe handles and grasping suaces do not allow for safe handling and
control of the tool in unexpected situations.
5) Seice
a) Have your power tool seiced by a qualied repair person using only identical
replacement pas. This will ensure that the safety of the power tool is maintained.
1) Guarding related warnings
a) Keep guards in place. Guards must be in working order and properly mounted. A
guard that is loose, damaged, or not functioning correctly must be repaired or
replaced.
b) Always use saw blade guard, riving knife and anti-kickback device for eve
through–cutting operation. For through-cutting operations where thesaw blade cuts
completely through the thickness of the workpiece, the guard and other safety
devices help reduce the risk of inju.
06
c) Immediately reattach the guarding system after completing an operation (such as
rabbeting, dadoing or resawing cuts) that requires the removal of the guard, riving
knife and/or anti-kickback device. The guard, riving knife, and anti-kickback device
help to reduce the risk of inju.
d) Make sure the saw blade is not contacting the guard, riving knife or the work-
piece before the switch is turned on. Inadveent contact of these items with the saw
blade could cause a hazardous condition.
e) Adjust the riving knife as described in this instruction manual. Incorrect spacing,
positioning and alignment can make the riving knife ineective in reducing the
likelihood of kickback.
f) For the riving knife and anti-kickback device to work, they must be engaged in the
workpiece. The riving knife and anti-kickback device are ineective when cutting
workpieces that are too sho to be engaged with the riving knife and anti-kickback
device. Under these conditions, a kickback cannot be prevented by the riving knife
and antikickback device.
g) Use the appropriate saw blade for the riving knife. For the riving knife to function
properly, the saw blade diameter must match the appropriate riving knife and the
body of the saw blade must be thinner than the thickness of the riving knife and the
cutting width of the saw blade must be wider than the thickness of the riving knife.
2) Cutting procedures warnings
a) DANGER: Never place your ngers or hands in the vicinity or in line with
the saw blade. A moment of inattention or a slip could direct your hand toward the
saw blade and result in serious personal inju.
b) Feed the workpiece into the saw blade or cutter only against the direction of
rotation. Feeding the workpiece in the same direction that the saw blade is rotating
above the table may result in the workpiece, and your hand, being pulled into the
saw blade.
c) Never use the mitre gauge to feed the workpiece when ripping and do not use the
rip fence as a length stop when cross cutting with the mitre gauge. Guiding the
workpiece with the rip fence and the mitre gauge at the same time increases the
likelihood of saw blade binding and kickback.
d) When ripping, always apply the workpiece feeding force between the fence and
the saw blade. Use a push stick when the distance between the fence and the saw
blade is less than 150 mm, and use a push block when this distance is less than 50
mm. “Work helping” devices will keep your hand at a safe distance from the saw
blade.
07
e) Use only the push stick provided by the manufacturer or constructed in accor-
dance with the instructions. This push stick provides sucient
distance for the hand from the saw blade.
f) Never use a damaged or cut push stick. A damaged push stick may break causing
your hand to slip into the saw blade.
g) Do not peorm any operation “freehand”. Always use either the rip fence or the
mitre gauge to position and guide the workpiece. “Freehand” means using your
hands to suppo or guide the workpiece, in lieu of a rip fence or mitre gauge.
Freehand sawing leads to misalignment, binding and kickback.
h) Never reach around or over a rotating saw blade. Reaching for a workpiece may
lead to accidental contact with the moving saw blade.
i) Provide auxilia workpiece suppo to the rear and/or sides of the saw table for
long and/or wide workpieces to keep them level. A long and/or wide workpiece has a
tendency to pivot on the table’s edge, causing loss of control, saw blade binding and
kickback.
j) Feed workpiece at an even pace. Do not bend or twist the workpiece. If jamming
occurs, turn the tool o immediately, unplug the tool then clear the jam. Jamming
the saw blade by the workpiece can cause kickback or stall the motor.
k) Do not remove pieces of cut-o material while the saw is running. The material
may become trapped between the fence or inside the saw blade guard and the saw
blade pulling your ngers into the saw blade. Turn the saw o and wait until the saw
blade stops before removing material.
l) Use an auxilia fence in contact with the tabletop when ripping workpieces less
than 2 mm thick. A thin workpiece may wedge under the rip
fence and create a kickback.
3) Kickback causes and related warnings
Kickback is a sudden reaction of the workpiece due to a pinched, jammed saw blade
or misaligned line of cut in the workpiece with respect to the saw blade or when a
pa of the workpiece binds between the saw blade and the rip fence or other xed
object.
Most frequently during kickback, the workpiece is lifted from the table by the rear
poion of the saw blade and is propelled toward the operator.
Kickback is the result of saw misuse and/or incorrect operating procedures or
conditions and can be avoided by taking proper precautions as given below.
08
a) Never stand directly in line with the saw blade. Always position your body on the
same side of the saw blade as the fence. Kickback may propel the workpiece at high
velocity toward anyone standing in front and in line with the saw blade.
b) Never reach over or in the back of the saw blade to pull or suppo the workpiece.
Accidental contact with the saw blade may occur or kickback may drag your ngers
into the saw blade.
c) Never hold and press the workpiece that is being cut o against the rotating saw
blade. Pressing the workpiece being cut o against the saw blade will create a
binding condition and kickback.
d) Align the fence to be parallel with the saw blade. A misaligned fence will pinch the
workpiece against the saw blade and create kickback.
e) Use a feather board to guide the workpiece against the table and fence when
making non-through cuts such as rabbeting, dadoing or resawing cuts. A feather-
board helps to control the workpiece in the event of a kickback.
f) Use extra caution when making a cut into blind areas of assembled workpieces.
The protruding saw blade may cut objects which can cause kickback.
g) Suppo large panels to minimize the risk of saw blade pinching and kickback.
Large panels tend to sag under their own weight. Suppo(s) must be placed under
all poions of the panel overhanging the tabletop.
h) Use extra caution when cutting a workpiece that is twisted, knotted, warped or
does not have a straight edge to guide it with a mitre gauge or along the fence. A
warped, knotted, or twisted workpiece is unstable and causes misalignment of
the ke with the saw blade, binding and kickback.
i) Never cut more than one workpiece, stacked veically or horizontally. The saw
blade could pick up one or more pieces and cause kickback.
j) When restaing the saw with the saw blade in the workpiece, centre the saw
blade in the ke so that the saw teeth are not engaged in the material. If the saw
blade binds, it may lift up the workpiece and cause kickback when the saw is
restaed.
k) Keep saw blades clean, sharp, and with sucient set. Never use warped saw
blades or saw blades with cracked or broken teeth. Sharp and properly set saw
blades minimize binding, stalling and kickback.
Tabla de contenidos
Otros manuales de Sierra de VEVOR
VEVOR
VEVOR DC305 Manual de usuario
VEVOR
VEVOR QH-50 Manual de usuario
VEVOR
VEVOR TC180II Manual de usuario
VEVOR
VEVOR M1H-ZP7-254-1 Manual de usuario
VEVOR
VEVOR HBS350 Manual de usuario
VEVOR
VEVOR HC-210 Manual de usuario
VEVOR
VEVOR QH-03 Manual de usuario
VEVOR
VEVOR RD03-4001 Manual de usuario
VEVOR
VEVOR J1G-ZB-355G-3 Manual de usuario
VEVOR
VEVOR DC235 Manual de usuario
