Vestil CART-550-AS Manual de usuario

Instruction Manual

ForAutoShiftHydraulicLiftTable

Model Number: CART-550-AS

Note: Owner/Operator must read and understand this Instruction

Manual before operating the lift & tilt table.

Contents

1 WARNING 2

2 CAUTION 2

3 NAME OF PARTS 3

4 HOW TO ASSEMBLE 4

5 DAILY INSPECTION 6

6 OPERATING LIFTTABLE 6

7 SERVICE INSTRUCTION 7

8 HYDRAULIC CIRCULT 7

9 SPARE PARTS LIST 8

10 TROUBLES SHOOTING 10

Operation and Service Manual

READ THIS MANUAL CAREFULLY AND BE SURE TO UNDERSTAND ALL THE INSTRUCTIONS BEFORE

OPERATING THE LIFT TABLE. KEEP THIS MANUAL ON FILE FOR FUTURE REFERENCE AND IF LOST, PLEASE

CONTACT YOUR LOCAL SUPPLIER FOR A NEW COPY. IF THE WARNING/CAUTION DECAL ON THE UNIT IS

WORN, TORN OR LOST, PLEASE CONTACT YOUR LOCAL SUPPLIER FOR A NEW DECAL.

NOTE: For this manual, WARNING means that there may be a condition where danger is present that could lead to

death or serious injury. CAUTION means there is a condition present that can lead to injury or property damage.

1. WARNING

1. Keep hands and feet clear of the scissors mechanism.

2. DO NOT allow personnel to stand in front of or behind the lift table when it is moving.

3. DO NOT move the lift table when it is in a raised position. The load could become unbalanced and fall.

4. Personnel should never be positioned under the table.

5. DO NOT overload the lift table.

6. Keep your feet clear of the rolling wheels. Injury could result.

7. Ensure that the floor is level and flat when moving the lift table. The load could fall if the floor is not level.

8. DO NOT use the lift table on sloped or inclined surfaces, as the lift table may become erratic and pose danger.

9. DO NOT use the lift table to elevate personnel. This could result in severe injury.

2. CAUTION

1. Before operating the lift table, ensure that you read this operation manual carefully and understand its

instructions completely. Improper operation could result in injury or property damage.

2. This lift table is a movable lifter designed to elevate or lower a rated load onto a table or flat surface. DO NOT

use the lift table for anything other than its intended purpose.

3. DO NOT allow personnel to operate the lift table who are not qualified or familiar with the equipment.

4. DO NOT lower the table too fast. This could unsettle the load and fall, causing injury or property damage.

5. Pay attention to the stability of the load. Do not operate the lift table if load becomes unstable.

6. Ensure that the lift table is braked when sliding a load on or off a table or flat surface.

7. All loads must be distributed evenly on at least 80% of the table area. DO NOT set loads to the side or ends of

the lift table surface.

8. DO NOT use the lift table if a load is unstable, unbalanced or loosely stacked.

9. Observe regular maintenance work according to the service manual instructions.

10. It is prohibited to modify the lift table without the manufacturer’s written consent. Modifying the lift table without

the manufacturer’s consent will void the warranty.

11. When servicing the lift table, remove any loads and use the safety stopper to prevent the table from

accidentally lowering.

12. Only use the lift table under dry conditions. This lift table is not designed to be water resistant.

3. NAME OF PARTS

4. Assembly Instructions

Ensure that the “Lift Table” is sufficiently secured before beginning to assemble.

A spanner tool and caliper are required when assembling the lift table. Clamping tools, such as

monkey wrenches can also be used.

Locatethesepartsforassembly Correctlyassembled

4.1 Secure the handle on the chassis using two bolts as well as the flat washers and spring washer.

4.2 Foot pedal assembly

1) Place the foot pedal into the chassis pipe 2) Tighten the bolts

4.3 Lift the platform and place two support bars that will secure and hold the chassis steady.

4.4. To attach the release handle:

4.4.1 Connect the chain to the bottom of the pump.

a) Remove the cotter pins from the axle

b) Secure the chain into the pump block using cotter pins and the axle.

4.4.2 Securing the chain into the chassis groove:

Using two washers, put the bolt into the middle of thread groove and then tighten the nut.

4.4.3 Clip the chain on the handle.

4.4.4. Once assembled, the lift table will activate, lift and lower easily when the lift handle is released. If the table

will not lower, please adjust using steps a) or b)

a) Loosen the up and down nuts, pull the release wire up for a snug fit, and then tighten the nuts until the

table lowers smoothly.

、

b) Loosen the up and down nuts, Pull the release wire down, and then tighten the nuts until the table lowers

smoothly.

5. DAILY INSPECTION

Daily inspection is a good means to find any possible malfunction or fault with the lift table. Check the lift table on

the following points before operation.

CAUTION

DO NOT use the lift table if any malfunction or fault is detected.

(1) Check for scratches, bending or cracking on the lift table.

(2) Check for any cylinder oil leakage.

(3) Check the vertical creep of the table.

(4) Check for smooth rotation of the wheel.

(5) Check for brake function.

(6) Ensure that all bolts and nuts are tightened securely.

6. OPERATING THE LIFT TABLE

6-1. How to use the brake.

CAUTION

Ensure that the brake for the lift table is set when it is not in use to prevent sudden movement.

The brake is located on the right side of the swivel caster.

(1) To set the brake, press the brake pedal.

(2) To release the brake, lift up the brake pedal.

6-2. Lifting the table

WARNING

1. DO NOT overload the lift table; ensure the load is within its rated capacity.

2. All loads must be distributed evenly on at least 80% of the table area. DO NOT set loads to the side

or ends of the lift table surface.

Press the lifting pedal several times until the table reaches the desired position.

The table does not elevate once it has reached the highest possible position even if the lifting pedal is continually

pressed.

The table lowers slightly after reaching the highest position.

NOTE:

The hydraulic cylinder is designed to hold the table. As is the nature of the hydraulic system, the table lowers

very slowly over an extended period of time, Please note the table will not stay at the same position

indefinitely.

6-3. Lowering table

WARNING

Keep your feet and hands clear of the scissors mechanism.

Pull the lowering lever up and table lowers.

7. Service instruction

7-1. Change hydraulic oil every 12 months.

7-2. Lubricate each point described below every month:

Lubricating Points

(1) Fitting of cylinder……Oil

(2) Roller friction surface……Grease

(3) Link Pin ……Oil

(4) Pedal fitting point……Oil

(5) Link center pin……Oil

(6) Joint……Grease

(7) Grease nipple……Grease

(8) Hydraulic circuit

8. Hydraulic Circuit

9. LIFT TABLE SPARE PARTS LIST

LIFT TABLE SPARE PARTS LIST

NO DESCRIPTION QTY NO DESCRIPTION QTY NO DESCRIPTION QTY

1. Seal cover d35×D43.5×5 1 47. Reflux rod 1 93. Safety rod 2

2. Cylinder cover 1 48. O-ring d4×1.8 1 94. Spring washer 10 16

3. O-ring d75×3.55 1 49. Guide casing 1 95. Nut M10 2

4. O-ring d35.5×3.55 1 50. Protect casing 1 96. External scissors lever 1

5. Piston Rod 1 51. Lever 1 97. Bushing 2

6. Spacing casing 1 52. Lever bushing 1 98. Roller for chassis 2

7. Guideing δ2×15 1 53. Washer 6 2 99. Bushing 2

8. O-ring D20×2.4 1 54. Spring washer 6 2 100. Pin axle for chassis 1

9. Seal ring d39×D45×4.5 1 55. Screw M6×16 1 101. Pin axle for table 1

10. Retainer for piston rod 1 56. Putpressureassemblyline 1 102. Bushing 2

11. Spacing retainer 18 1 59. Washer 8 2 103. Oil cup 1

12. Piston 1 61. Spring pin 1 104. Bolt M8×12 1

13. Cylinder 1 62. Control link 1 105. Internal scissors lever 1

14. Washer for cylinder 1 63. Handle 1 106. Chassis 1

15. Reservior 1 64. Spacing casing 2 107. axle 1

16. O-ring d10×2.65 1 65. Spring washer 12 2 108. Screw M10×25 16

17. Filler screw 1 66. Hex screw M12×30 2 109. Nut M10 16

18. O-ring d75×2.65 1 67. Split pin 2×15 1 110. Wheel 2

19. Washer for reservior 1 68. Pin 1 111. Wheel 2

20. Steel ball 5 1 72. Pedal bent pipe 1 112 Rod 1

21. Spring base 1 73. Hex screw M8×20 2 113 Rod 1

22. Regulating pressure spring 1 74. Shake link 1 114 Bolt M6×8 1

23. Regulating pressure screw 1 75. Spring 2 115 Screw M6×30 1

24. O-ring d7.1×1.8 1 76. Pin axle 2 116 Cover-type nut M6 1

25. End cover 1 77. Retainer 10 2 117 washer 1

26. O-ring d15×2.65 2 78. Link 2 118 Plug 1

27. Regulating speed spring 1 79. Table 1 119 Steel ball φ6 1

28. Regulating slide-valve 1 80. Retainer 20 7 120 Spring 1

29. Regulating speed spring casing 1 81. Roller for table 2 121 Spring seat 1

30. Regulating speed slide-casing 1 82. Bushing 2 122 Spring 2

31. Steel ball 7 1 83. Split pin 3.2×26 2 123 Pin 2.5×8 1

32. O-ring d6.9×1.8 1 84. Nut M16 2 124 Steel ball φ4 2

33. Conical valve 1 85. Washing 2 125 Pump plunger 1

34. Spring 1 86. Bushing 2 126 O-ring φ28×2.4 1

35. Check valve casing 1 87. Pin axle for scissors 2 127 Block ring 1

36. O-ring d10×1.8 1 88. Spring washer 8 2 128 Pump body 1

37. Check valve screw 1 89. Hex screw M8×16 2 129 Seal ring φ20×φ28×5 1

44. Pump body 1 90. Spring pin 8×30 2 130 Seal cover φ20×φ28×4.5 1

45. O-ring d10.6×2.65 1 91. Screw bolt M10×40 2

46. Spring 1 92. Washer 10 36

A Pump ass’y 1～50,112,113，117～130

B Swivel wheel ass’y 111

C Front wheel ass’y 110

D Sealkit ass’y 1,3,4,7,8,9,16,18,24,26,32,36,45,48,117,126,129,130

E Handle ass’y 53,54,56,61,62,63,67,68,115,116

Tabla de contenidos

Otros manuales de Sistema de elevación de Vestil

Vestil

Vestil FMDL Series Manual de usuario

Vestil

Vestil DLH-CL2-1 Manual de usuario

Vestil

Vestil HDDL-55 Manual de usuario

Vestil

Vestil WTJ-20 Series Manual de usuario

Vestil

Vestil EHE-2 Manual de usuario

Vestil

Vestil FRA-4-238 Manual de usuario

Vestil

Vestil PAL-D Manual de usuario

Vestil

Vestil FMDL Series Manual de usuario

Vestil

Vestil WP Series Manual de usuario

Vestil

Vestil NVD-40 Manual de usuario

Vestil

Vestil OLF-4-42 Manual de usuario

Vestil

Vestil EHLT-E Manual de usuario

Vestil

Vestil FM Series Manual de usuario

Vestil

Vestil RR Series Manual de usuario

Vestil

Vestil JMD-1000 Manual de usuario

Vestil

Vestil CYL-P-LUG Series Manual de usuario

Vestil

Vestil PMPS Series Manual de usuario

Vestil

Vestil FTTM-2 Manual de instrucciones

Vestil

Vestil CH-200 Series Manual de usuario

Vestil

Vestil CART-600-S-HR Manual de usuario

Vestil

Vestil LM-HP-4 Manual de usuario

Vestil

Vestil MH-V10 Manual de usuario

Vestil

Vestil OLA-4-42 Manual de usuario

Vestil

Vestil HLD Series Manual de usuario

Manuales populares de Sistema de elevación de otras marcas

morse

morse 82H-124 Manual de usuario

Braun

Braun NL955 Series Manual de usuario

haacon

haacon 1889.10 Manual de usuario

Protekt

Protekt AT 252 Manual de usuario

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manual de usuario

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manual de usuario

Genie

Genie Z-60/34 Manual de usuario

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manual de usuario

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manual de usuario

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manual de programación

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manual de programación

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manual de programación

BERG

BERG BeNomic EasyLeaf Manual de usuario

Powermate

Powermate LiftGate LG-3 Manual de usuario

Snorkel

Snorkel TM12 Series Manual de usuario

Terberg

Terberg OMNIDEKA Manual de usuario

Harmar Mobility

Harmar Mobility AL625 Instrucciones de funcionamiento

Rotary

Rotary SPO16 Manual de usuario