Vertex Standard DMU-2000 Instrucciones generales

3/16/10

This procedure is used to update the flash programming for

the DMU-2000.

V4.21 or V5.11 version software is ONLY needed when the DMU-2000 is used with the New

FTdx5000 Transceiver. There is no change from V4.20 or V5.10 when used with the FT-2000/D

or FT-950 radios. If you already have System File [CF1] V0.08 or V0.09 you only need to install

the [CF2] V4.21 or V5.11 application file.

* This is the latest software and is compatible with all three FT-950, FT-2000/D and FTdx5000 series.

Check which version DMU software you have on your unit.

While holding the three buttons [GEN]＋[50]＋[ENT] turn the radio on. The software version will be

displayed in the lower right of the VFO-A window (FTdx5000 version will be shown in the Center

OLED display) for 5 seconds then the radio will start up in normal operation. Example: DMU-2000

software version 0511.

FTdx5000 FT-2000/D

Two types of computers are used in the DMU-2000. You must use the correct software for

your computer.

•If you have version 03xx or 04xx you must down load V0.08/V4.21. If you have V0421 you

have the latest software and do not need to update.

•If you have 05xx you must download V0.09/5.11. If you have V0511 you have the latest

software and do not need to update.

*You may also check the software level on the DMU boot up screen. Turn on the DMU front and rear

main power to boot the DMU processor. IF the YAESU boot up screen shows this small Phoenix BIOS

logo at the lower right of the screen, you have version 05xx and must download V0.09/5.10. If

the Phoenix logo is not shown, you have version 03xx or 04xx you must down load V0.08/V4.20.

SYSTEM (OS) APPLICATION

PC Ver.0.08 Ver.4.21 (03xx or 04xx)

PC Ver.0.09 Ver.5.11 (05xx)

After you confirm the type of software it is very important that you only down load the correct

version from the Yaesu website.

Software Version: 03xx, 04xx or

05xx.

If you already have software Ver.

0421 or 0511 it is not necessary to

update the DMU-2000 again.

(This image & version is for illustration

only)

CAUTION: Only down load the correct software for your version 0.08/4.21 or 0.09/5.11 for the DMU-

2000. Do not keep both versions on your computer.

Ver. 4.21 or 5.11 CPU implements improvements also includes all previous updates):

•ONLY Changes to support the New FTdx5000 Series Transceiver

Install the data file to PC

1. Down load the DMU-2000 data file [DMU-2000_V008_2-25-10.zip] or [DMU-2000_V009_2-

25-10.zip] from the following website:

http://www.yaesu.com/indexVS.cfm?cmd=DisplayProducts&ProdCatID=102&encProdID=66EA

91711DFB68C03DED4AD35153E12C&DivisionID=65&isArchived=0

2. Save the DMU-2000 data file [DMU-2000_2-25-10.zip] to the desktop on your computer.

3. Unzip and Extract the contents of [DMU-2000_2-25-10.zip] to the desktop of your computer.

4. You will find the CF1 and CF2 folders on your desktop.

The programmer and software are now stored on your computer on the desktop. The files designated

in the last step above are ready to create two CF cards to use in updating your DMU-2000.

*You must have two separate, blank CF cards (32 MB or more) and have a CF card reader slot.

NOTE: Do not copy the folders to the CF cards, only the files (V0.xxx WinZip and md5sum). The

system and the application files must be on separate CF cards. Do not save them to the same CF card.

Be sure the CF card does not contain any previous data or partitions. You may need to make a single

patrician and reformat a previously used CF card.

Now you will transfer each of the needed files to separate CF cards. When you open the CF1 folder

you will see the two files. Copy both system files and paste them to the CF card drive and create a CF

card. Remove the CF1 card and insert another card. Now open the CF2 folder and copy or paste both

application files to the CF card drive and create a CF card.

It is strongly recommended that you mark each CF card as CF1 and CF2 to prevent mixing up the

files. The SYS file (CF1) must be installed before CF2 or the update will not work.

DMU-2000_V008_2-25-10.zip DMU-2000_V009_2-25-10.zip

If you have version 03xx or 04xx, you must

create two cards; one with CF1_V008-sys and

another with CF2_V421-app.

•Open the CF1 folder and copy two files to

CF card 1

•Open the CF2 folder and copy two files to

CF card 2

If you have version 05xx, you must create two

cards; one with CF1_V009-sys and another

with CF2_V511-app.

•Open the CF1 folder and copy two files to

CF card 1

•Open the CF2 folder and copy two files to

CF card 2

After creating CF1 and CF2 cards, follow the instructions below

*We recommend you save to the CF card, any personal settings you want to restore after the update. Please

see the DMU-2000 Data Management Operation Manual for the procedure to save your settings to a CF

card. Map and Time settings will be set to default.

*When you insert the CF card into the slot, please insure that the white side (ridge side) of the CF card

is up. If the CF card is inserted incorrectly, the DMU-2000 may be damaged.

1. Turn off the DMU power switch on the rear panel and wait 1 minute.

2. Connect a keyboard, if one is not already connected.

3. Insert the system Compact Flash Card CF1 (V0.xx-sys) into the DMU card slot.

4. Turn the DMU rear panel power switch on.

5. When the question appears, “CF has system update file, Are you sure to update? (y/n)>”

Please answer yes (y + enter).

6. Wait a minute for the system to check the current version. The program level will be shown on the

monitor display. Answer yes or no (y + enter, or n + enter) from the keyboard to each question of

the install sequence. If the present version and the new version listed on the screen are identical

numbers, you should answer no. (If you answer no, when the screen blanks, remove the CF1 card,

or the system will repeat the sequence.) If the new version is higher, answer yes (y + enter).

7. When programming is complete, the screen will be blank. Remove the CF1 card and Turn the

rear panel DMU power switch off. Wait one minute.

Now you can insert CF2 (app) and Follow the same procedure instructions 1 thru 7:

8. When programming is complete, remove the Compact flash card CF2 (V0.xx-app). Turn the rear

panel DMU power switch off. Wait one minute.

9. Turn on the FT-2000/D, FT-950 or FTdx5000 and the DMU-2000 rear and front power switches,

and confirm the DMU firmware is updated to V4.21 or V5.11 depending on the type of DMU-

2000 computer. Refer to the top of page 1 to check which version DMU software you have on

your unit.

10. You will need to re-enter your map location, clock and other settings if necessary. The updating

process is now complete.

We hope this new software will increase your enjoyment of your DMU-2000. Thank you for choosing

Yaesu radios. If you have any problems or questions please contact Vertex Standard, Amateur Tech

Support. amateurtech@vxstdusa.com

Best regards,

Mikio Maruya, WA6F

Executive Vice President

Engineering & Customer Service

Vertex Standard USA, Inc.

Vertex Standard USA, Inc. | 10900 Walker St. | Cypress, CA 90630 | 714.827-7600 | FAX: 714.827-8100

www.vertexstandard.com

Tabla de contenidos

Otros manuales de Transceptor de Vertex Standard

Vertex Standard

Vertex Standard VXA-300 Pilot III Manual de usuario

Vertex Standard

Vertex Standard VX-146 Manual de usuario

Vertex Standard

Vertex Standard VXA-150 Manual de usuario

Vertex Standard

Vertex Standard VX-351PMR446 Manual de usuario

Vertex Standard

Vertex Standard VX-820 series Manual de usuario

Vertex Standard

Vertex Standard VX-2500U Manual de usuario

Vertex Standard

Vertex Standard VXA-220 Manual de usuario

Vertex Standard

Vertex Standard VX-410 Series Manual de usuario

Vertex Standard

Vertex Standard VX-450 series Manual de usuario

Vertex Standard

Vertex Standard VX-5500V Manual de usuario

Vertex Standard

Vertex Standard VX-456 Manual de usuario

Vertex Standard

Vertex Standard VX-4107 Manual de usuario

Vertex Standard

Vertex Standard VX-127 Manual de usuario

Vertex Standard

Vertex Standard VXR-9000U-A Manual de usuario

Vertex Standard

Vertex Standard Pilot VXA-210 Manual de usuario

Vertex Standard

Vertex Standard EVX-531 Manual de usuario

Vertex Standard

Vertex Standard VX-261 Manual de usuario

Vertex Standard

Vertex Standard VXA-710 SPIRIT Manual de usuario

Vertex Standard

Vertex Standard VXR-9000U Manual de usuario

Vertex Standard

Vertex Standard VX-820 series Manual de usuario

Vertex Standard

Vertex Standard VX-3200V Manual de usuario

Vertex Standard

Vertex Standard VX-2500U Manual de usuario

Vertex Standard

Vertex Standard VX-2100 Series Manual de usuario

Vertex Standard

Vertex Standard VX-4200 Series Manual de usuario

Manuales populares de Transceptor de otras marcas

Yaesu

Yaesu FT-7B Manual de usuario

Kenwood

Kenwood ProTalk TK-3201 Manual de usuario

Texas Instruments

Texas Instruments TLK10232 Manual de usuario

Mizuho

Mizuho MX-2 Guía del producto

Kenwood

Kenwood TK-3180 Manual de operación y mantenimiento

Blitz

Blitz MJ-398U Manual de usuario

Utilicom

Utilicom LongRanger 2050 Manual de usuario

Standart

Standart HX290UKA Manual de usuario

Altronix

Altronix Pace1PTM Manual de usuario

Kirisun

Kirisun PT2208 Manual de usuario

ELECRAFT

ELECRAFT KX2 Manual de usuario

Zodiac

Zodiac K3 Manual de usuario

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manual de usuario

Kenwood

Kenwood TK-2217 Manual de usuario

Siemens

Siemens PSO 4000 Manual de usuario

Kenwood

Kenwood TS-590SG Manual de usuario

Midland

Midland G8E-BT Manual

ComNav

ComNav Mariner X2 Manual de usuario