Vertex Standard EVX-5300 Manual de usuario

EVX-5300

Operating Manual

prOgraMMable FunctiOns

Features

 6ProgrammableFunctionKeys

 2-ToneEncode/Decodeø

 5-ToneEncode/Decodeø

 MDC-1200®Encode/Decodeø

 HornAlert

 PA(PublicAddress)

 Scan

 DualWatch

 FM-Scan(Follow-MeScan)

 TAScan

 Privacy

 Encryptionø

 VOX

 TalkAround

 Emergency

 LoneWorker

 TXSaveDisable

 ARTSTM/ARTS

TM(AutoRangeTranspondSystem)

ø:Analogmodeonly

Unsafe Radiation Distance

Congratulations!

You now have at your ngertips a valuable communications tool: a Vertex Stan-

dard two-way radio! Rugged, reliable and easy to use, your Vertex Standard radio

will keep you in constant touch with your colleagues for years to come, with negli-

gible maintenance downtime.

Please take a few minutes to read this manual carefully. The information presented

here will allow you to derive maximum performance from your radio.

We’re glad you joined the Vertex Standard team. Call on us anytime, because com-

munications is our business. Let us help you get your message across.

Notice !

There are no owner-serviceable parts inside the transceiver. All service jobs

must be referred to an authorized Vertex Standard Service Representative.

Consult your Authorized Vertex Standard dealer for installation of optional

accessories.

Safety/WarNiNg iNformatioN

WARNING - DO NOT operate the EVX-5300 radio when any person(s)

(bystanders) outside the vehicle are within the distances shown in the chart

at the bottom of this section.

Safety Training information:

Antennas used for this transmitter must not exceed an antenna gain of

0 dBi. The radio must be used in vehicle-mount congurations with a maxi-

mum operating duty cycle not exceeding 50 %, in typical Push-to-Talk con-

gurations.

This radio is restricted to occupational use, work related operations only

where the radio operator must have the knowledge to control the exposure

limits of passengers and bystanders by maintaining the minimum separa-

tion distance shown below.

Failure to observe these restrictions will result in exceeding the FCC RF

exposure limits.

Antenna Installation:

For rear deck trunk installation, the antenna must be located at least the fol-

lowing distance away from rear-seat passengers in order to comply with the

FCC RF exposure requirements.

For roof top installations, the antenna must be placed in the center of the

roof.

VHF Model UHF Model

2.9 Feet (0.89 m)2.36 Feet (0.72 m)

EVX-5300 OpErating Manual

IntroductIon

The EVX-5300 is full-featured Digital/Analog transceiver designed for exible

mobile and base station business communications in the VHF/UHF Land Mobile

bands. This transceiver designed for reliable business communications in a wide

variety of applications with a wide range of operating capability provided by their

leading-edge design.

The EVX-5300 operates using the TDMA protocol for spectrum and power ef-

ciency and lower total equipment cost compared to FDMA. Digital eliminates

noise and static from voice transmit to only deliver the intended voice message

crisply and clearly. The EVX-5300 feature the AMBE+2™ vocoder for enhanced

voice quality.

This transceiver allows up to 8 memory channels. Important channel frequency

data is stored in the ash memory on the CPU, and is easily programmable by a

Vertex Standard licensed dealers using a personal computer with Vertex Standard

Programming equipment FIF-12 USB Programming Interface and CT-104A Con-

nection Cable for FIF-12 and CE142 Software. Or, once programmed, cloning

cable CT-4 can be used to program portable to portable directly.

The pages which follow will detail the many advanced features provided in the

EVX-5300 Series transceiver. After reading this manual, you may wish to consult

with your Network Administrator regarding precise details of the conguration of

this equipment for use in your application.

For North American Users Regarding 406 MHz Guard Band

The U.S. Coast Guard and National Oceanographic and Atmospheric Ad-

ministration have requested the cooperation of the U.S. Federal Communi-

cations Commission in preserving the integrity of the protected frequency

range 406.0 to 406.1 MHz, which is reserved for use by distress beacons.

Do not attempt to program this apparatus, under any circumstances, for op-

eration in the frequency range 406.0 - 406.1 MHz if the apparatus is to be

used in or near North America.

EVX-5300 OpErating Manual

controls & connectors

Front Panel

Important! - All buttons located on the Front Panel are Programmable Function

(PF) keys, congured according to your network requirements and programmed

by your Vertex Standard dealer. The instructions below describe a typically-cong-

ured radio.

 PWR ( ) Button

Press and hold in this button for 2 seconds to toggle the transceiver’s power

“on” and “off”.

 VOL Knob

Turn this control clockwise to increase the volume.

 Microphone Jack

Connect the microphone plug to this jack.

 TX/BUSY Indicator

Indicates transceiver’s Transmit/Receive Status.

 [P1] - [P4] Keys (Programmable Function Keys)

These keys can be set up for special applications, such as High/Low power

selection, Monitor, Talk-Around, etc., as determined by your network require-

ments and programmed by your Vertex Standard dealer.

 []/[] Keys (Programmable Function Keys)

In the factory default, pressing either key changes the current channel.

 

 



EVX-5300 OpErating Manual

controls & connectors

transceIver status IndIcator

 Channel Number Indicator

Indicates the operating channel.

 Transceiver Status Indicator

The “A”, “B”, and “C” indicators show current transceiver status, which can

be customized via programming by your Vertex Standard dealer to meet your

communications/network requirements. The possible these indicators are ex-

plained below.

status

IndIcator descrIptIon

A B C

MONI This indicator is illuminated constantly when the

signaling feature is disabled. The indicator blinks

while the audio is passing normally.

SCAN CH Illuminates the indicator when the scan enabled

channel is recalled

Low Power Illuminates the indicator when the radio’s transmit-

ter is set to the “Low Power” mode

TA (Talk Around)Illuminates the indicator when the “Talk Around”

function is activated.

Privacy (Digital)

Encryption (Analog)

Illuminates the indicator when the “Privacy” (Digital

mode) or “Voice Scrambler” (Analog mode) func-

tion is enabled.

Emergency Illuminates the indicator when the “Emergency”

feature is activated.

Horn Alert Illuminates the indicator when the “Horn Alert” fea-

ture is activated.

PA (Public Address)Illuminates the indicator when the radio is turned

to a PA amplier.

Lock Illuminates the indicator when the “Lock” feature is

activated.

ACC2 Illuminates the indicator when the output port “2”

on the Accessory Connector is turned to “ON”.

RFC Illuminates the indicator when the radio is in the

“Ready for Communication” condition while operat-

ing with the 2-Tone or 5-Tone signaling.

EVX-5300 OpErating Manual

Rear Panel

controls & connectors







 Antenna Jack

The 50-Ohm coaxial feedline to the antenna must be connected here, using a

mini-UHF plug.

 13.6V DC Cable Pigtail with Connector

The supplied DC power cable must be connected to this 2-pin connector. Use

only the supplied fused cable, extended if necessary, for power connection.

Replace only with the same or equivalent type fuse.

 External Speaker Jack

An external loudspeaker may be connected to this 2-contact, 3.5-mm mini-

phone jack.

Caution: Do not connect either wire of this line to ground, and be certain that

the speaker has adequate capability to handle the audio output (12 W) from

the radio.

 D-Sub 15-Pin Accessory Connector

External TX audio line input, PTT (Push To Talk), Squelch, and external RX

audio line output signals may be obtained from this connector for use with ac-

cessories such as data transmission/reception modems, and external Channel

control input etc.

EVX-5300 OpErating Manual

BasIc operatIon

Important! - Before turning on the radio the rst time, conrm that the power con-

nections have been made correctly and that a proper antenna is connected to the

antenna jack.

Switching Power ON/OFF

 Press and hold in the PWR( ) button for 2 seconds to turn the radio on. The

channel number indicator will indicate the operating channel.

 Press the []/[] key to choose the desired operating channel. The radio an-

nounces the channel number, if the Channel Announcement Feature is enabled

via the clone editor software.

Setting the Volume

 Turn the VOL knob clockwise to increase the volume, and counterclockwise

to decrease it.

Transmitting

 To transmit, monitor the channel and make sure it is clear.

 Press the PF key which is programmed to the Monitor feature to listen for

channel activity.

 When receiving a call, transmit only after the incoming call ends. The radio

cannot receive a call and transmit simultaneously.

 Press the PTT switch.

 If the channel is clear, the TX/BUSY indicator will glow red (on the Analog

Channel) or blue (on the Digital Channel). The radio is now transmitting.

While holding in the PTT switch, speak across the face of the microphone in

a clear and normal voice. For best transmission, hold the microphone about

1-1/2 to 2 inches (4 ~ 5 cm) away from your mouth. Release the PTT switch

to receive.

 If the BCLO (Busy Channel Lockout) feature has been programmed on an ana-

log channel, the radio will not transmit when a carrier is present. Instead, the

radio will generate short beep three times. Release the PTT switch and wait for

the channel to be clear of activity.

 If the BTLO (Busy Tone Lockout) feature has been programmed on an analog

channel or CCLO (Color Code Lockout) feature has been programmed on

a digital channel, the radio can transmit only when there is no carrier being

received or when the carrier being received includes the correct tone (CTCSS

tone or DCS code) on an analog channel or correct code on a digital channel.

EVX-5300 OpErating Manual

Transmit Time-Out Timer

If the selected channel has been programmed for automatic time-out, you must

limit the length of each transmission. While transmitting, a beep will sound 10 sec-

onds before time-out. Another beep will sound just before the deadline; the red “TX”

indicator will disappear and transmission will cease soon thereafter. To resume

transmitting, you must release the PTT switch and wait for the “penalty timer” to

expire (if you press the PTT switch before this timer expires, the timer restarts,

and you will have to wait another “penalty” period).

Key Lock

In order to prevent accidental operating function/feature change or inadvertent

transmission, various aspects of the front panel’s keys may be locked out.

To activate the Locking feature, press and hold in the [P1] key while turning the

radio on. To disable the Locking feature, repeat this power-on procedure.

advanced operatIon

Programmable Function (PF) Keys

The EVX-5300 Series includes six Programmable Function (PF) keys. These PF

keys can be customized, via programming by your Vertex Standard dealer, to meet

your communications/network requirements.

The possible PF key programming features are illustrated on the next page, and

these functions are explained beginning after page 8. For further details, contact

your Vertex Standard dealer.

In this chapter, the following icons are used to indicate features supported in either

the “Analog” mode or “Digital” mode:

: Indicates a “Analog” mode only feature.

: Indicates a “Digital” mode only feature.

For features that are available in both “Analog” and “Digital” modes, no icon is

shown.

For future reference, check the box next to each function that has been assigned to

the PF key on your particular radio, and keep it handy.

BasIc operatIon

EVX-5300 OpErating Manual

FunctIon

programmaBle Key

(

press Key/press & Hold Key

)

mIcropHone Key

(

press Key/press & Hold Key

)

P1 P2 P3 P4   A B C D Ü#

None /////////// /

Monitor ////////////

Monitor -Momentarily- /-- /-- /-- /-- /-- /-- /-- /-- /-- /-- /-- /--

Lamp ////////////

Low Power ////////////

Privacy / Encryption ////////////

SQL OFF /////// / ////

SQL OFF -Momentarily- /-- /-- /-- /-- /-- /-- /-- /-- /-- /-- /-- /--

Beep Off ////////////

AF Minimum Volume ////////////

CH Announcement ////////////

Whisper ////////////

VOX ////////////

VOX Anti-Trip ////////////

Horn Alert ////////////

PA (Public Address)////////////

EXT ACC 1 /-- /-- /-- /-- /-- /-- /-- /-- /-- /-- /-- /--

EXT ACC 2 ////////////

Emergency /-- /-- /-- /-- /-- /-- /-- /-- /-- /-- /-- /--

Lone Worker ////////////

CH Up ////////////

CH Down ////////////

PRI-2 Set ////////////

PRI-2 Disable ////////////

PRI-2 ////////////

Direct CH 1 ////////////

Direct CH 2 ////////////

Direct CH 3 ////////////

Direct CH 4 ////////////

Scan ////////////

Dual Watch ////////////

FM Scan (Follow-Me Scan)////////////

SCAN Set ////////////

TA Scan ////////////

Talk Around (TA)////////////

RESET ////////////

Call 1 ////////////

Call 2 ////////////

Call 3 ////////////

Call 4 ////////////

Call 5 ////////////

Speed Dial ////////////

Call ////////////

Duty ////////////

TX Save Disable ////////////

Lock ////////////

advanced operatIon

EVX-5300 OpErating Manual

Description of Operating Functions

monItor

Press (or press and hold) the assigned PF key to cancel any signaling features.

monItor -momentarIly-

Cancel any signaling features while pressing the assigned PF key.

lamp

Press (or press and hold) the assigned PF key to toggle the back light of the key-

pad “On” and “Off”.

low power

Press (or press and hold) the assigned PF key to set the radio’s transmitter to the

“Low Power” mode. Press (or press and hold) the PF key again to return to “High

Power” operation when in difcult terrain.

When the radio’s transmitter is set to “Low Power” mode, the Transceiver Status

Indicator (“A”, “B” or “C”) will illuminate, if the “Low Power” status is assigned

to one of the Transceiver Status Indicator.

prIvacy

Press (or press and hold) the assigned PF key to toggle the Privacy feature “On”

and “Off”. The Privacy feature initiates an encryption algorithm that will protect

your communication from unauthorized eavesdropping.

When the Privacy feature is activated, the Transceiver Status Indicator (“A”, “B”

or “C”) will illuminate, if the “Privacy” status is assigned to one of the Transceiv-

er Status Indicator.

encryptIon

When the Voice Scrambler feature is enabled, press (or press and hold) the as-

signed PF key to toggle the voice encryption “On” and “Off”.

When the Voice Scrambler feature is activated, the Transceiver Status Indicator

(“A”, “B” or “C”) will illuminate, if the “Encryption” status is assigned to one of

the Transceiver Status Indicator.

sQl oFF

Press (or press and hold) the assigned PF key to open the SQL to hear background

noise (unmute the audio).

advanced operatIon

Otros manuales para EVX-5300

Tabla de contenidos

Otros manuales de Radio de Vertex Standard

Vertex Standard

Vertex Standard VX-4000 Series Manual de usuario

Vertex Standard

Vertex Standard VX-5500 Manual de usuario

Vertex Standard

Vertex Standard VX-6000 Manual de usuario

Vertex Standard

Vertex Standard VX-230 Series Manual de usuario

Vertex Standard

Vertex Standard EVX-261 Manual de usuario

Vertex Standard

Vertex Standard VX-1700 Series Manual de usuario

Vertex Standard

Vertex Standard VX-537 Manual de usuario

Vertex Standard

Vertex Standard VX-2500 Manual de usuario

Vertex Standard

Vertex Standard VX-1700 Series Manual de usuario

Vertex Standard

Vertex Standard VX-920 series Manual de usuario

Vertex Standard

Vertex Standard VX-450 series Manual de usuario

Vertex Standard

Vertex Standard VX-2500 Manual de usuario

Vertex Standard

Vertex Standard VXD-720 digital Manual de usuario

Vertex Standard

Vertex Standard VX-450 series Manual de usuario

Vertex Standard

Vertex Standard VX-1700 Series Manual de usuario

Vertex Standard

Vertex Standard VX-1700 Series Manual de usuario

Vertex Standard

Vertex Standard VX-160 Manual de usuario

Vertex Standard

Vertex Standard VX-4500 Series Manual de usuario

Vertex Standard

Vertex Standard VX-4100 Series Manual de usuario

Vertex Standard

Vertex Standard VX-2200 Series Manual de usuario

Vertex Standard

Vertex Standard VX-1400 Manual de usuario

Vertex Standard

Vertex Standard VX-170 Manual de usuario

Vertex Standard

Vertex Standard VX-4500 Series Manual de usuario

Vertex Standard

Vertex Standard VX-3200 Series Manual de usuario

Manuales populares de Radio de otras marcas

EisSound

EisSound KBSound iSelect Manual de usuario

Midland

Midland 1001LWX Manual de usuario

Konig

Konig HAV-SR41 Manual de usuario

Roberts

Roberts exprssion Manual de usuario

VDigi

VDigi DD3.0 Manual de usuario

Radio Shack

Radio Shack 21-1863 Manual de usuario

Roberts

Roberts Stream 207 Manual de usuario

Sony

Sony Walkman SRF-M97 Manual de usuario

Stanley

Stanley FatMax FMC770 Manual de usuario

auna

auna DAB-Radio 10026947 Manual de usuario

SOUNDMASTER

SOUNDMASTER UR190 Manual de usuario

HYT

HYT TC-320 Manual de usuario

auna multimedia

auna multimedia Yellowstone 10026851 Manual de usuario

B-Tech

B-Tech GMRS-V2 Manual de usuario

Weierwei

Weierwei VEV-V8 Manual de usuario

SOUNDMASTER

SOUNDMASTER DAB750 Manual de usuario

Telefunken

Telefunken TF-1505 Manual de usuario

Makita

Makita LXRM03 Manual de usuario