Verkada BZ11 Manual de usuario
Document
Document Details
Verkada Inc. 406 E. 3rd Ave, San Mateo, CA 94401
V1.0 (20230210)
(V1.0 first published 20230210)
Firmware
Firmware version can be verified on
Verkada Command command.verkada.com.
Product Model
This install guide pertains to model BZ11-HW
2All specifications are subject to change without notice
Copyright © 2023 Verkada Inc. All rights reserved.
Introduction
Overview
Verkada Inc. 406 E. 3rd Ave, San Mateo, CA 94401
3
LED Behavior
Solid Orange
Speaker is on and booting up.
Flashing Orange
Speaker is updating firmware.
Flashing Blue
Speaker is powered, but cannot
reach the server.
Solid Blue
Speaker is powered, and
connected to the server.
Register to Command
For easy registration and setup, scan the
QR code on the product, or proceed to:
verkada.com/start
Status LED
Scan the QR
code on the
product to
easily register it
to Command.
All specifications are subject to change without notice
Copyright © 2023 Verkada Inc. All rights reserved.
Introduction
What’s in the box
What you’ll need
●A working internet connection
●A smartphone or laptop
●A #2 Phillips driver (Screwdriver or power drill/driver.
Use hammer drill for masonry installation.)
●1/8 inch (3mm) drill bit for pilot holes
●5/32 inch (4 mm) impact rated hammer drill bit for masonry installation
●1/4 inch hex driver
●1/2 inch (12.7mm, or larger) drill bit for routing cable through wall
●A Cat5 or Cat6 Ethernet cable with a 0.2-0.25 inch diameter (5-6.5mm)
Verkada Inc. 406 E. 3rd Ave, San Mateo, CA 94401
4
Horn Speaker Mount Bracket
3 Masonry Screws 2 Accessory Mounting Machine Screws
(Accessory Brackets not included) 3 Wall Mounting Screws
& Anchors
2 Mount Bracket Fasteners
All specifications are subject to change without notice
Copyright © 2023 Verkada Inc. All rights reserved.
Installation
Mounting
Verkada Inc. 406 E. 3rd Ave, San Mateo, CA 94401
Use the mounting bracket to mark hole locations
on the wall surface.
For wood surfaces:
Mark 3x holes. Drill ⅛” pilot holes. Use a Phillips #2
driver to fasten mounting bracket in place with 3x
wall screws (M5 x 30mm).
For drywall:
Mark 3x holes. Press tip of drywall anchors into
drywall surface. Use a Phillips #2 driver to screw
plastic anchors into drywall surface. Use a Phillips
#2 driver to fasten mounting bracket in place
with 3x wall screws (M5 x 30mm; thread into the
plastic anchors).
For concrete or masonry:
Mark 2x holes (aligned with outer slots). Pilot holes
should be >2-½” from wall edges or corners. Drill
5/32” pilot holes >1-½” deep using a hammer drill
& impact-rated masonry bit. After drilling, clear
dust & debris from hole. Use a ¼” hex driver to
fasten mounting bracket in place with 2x
masonry screws (3/16” x 1-1/4"; screw kit includes 1
spare masonry fastener).
5All specifications are subject to change without notice
Copyright © 2023 Verkada Inc. All rights reserved.
Installation
Cable Sealing (1/3)
Verkada Inc. 406 E. 3rd Ave, San Mateo, CA 94401
Twist the outer Plastic Nut anti-clockwise
to remove it.
Remove Plastic Collar and Rubber Seal
from the enclosure. Disassemble
Rubber Seal from Plastic Collar.
Rubber Seal and Plastic Collar
are two separate parts.
6All specifications are subject to change without notice
Copyright © 2023 Verkada Inc. All rights reserved.
Installation
Cable Sealing (2/3)
Verkada Inc. 406 E. 3rd Ave, San Mateo, CA 94401
Thread the Plastic Nut and Plastic Collar onto
the PoE cable.
The Rubber Seal has a slit cut down its side.
Open the cut side & push the cable into place,
wrapping the Rubber Seal around the cable
jacket.
Please strictly follow the assembling
sequence and direction of components
as indicated in the picture.
Important
7
Rubber Seal
Plastic Collar
Plastic Nut
All specifications are subject to change without notice
Copyright © 2023 Verkada Inc. All rights reserved.
1
2
3
Installation
Verkada Inc. 406 E. 3rd Ave, San Mateo, CA 94401
Slide Plastic Collar and Rubber Seal
into the base.
Grip the cable near the RJ45 plug & push it
through the cable gland. Push the cable &
plug into the internal connector mounted
inside the housing.
Please note:
Locking clip on Ethernet cable should be
facing down.
Cable Sealing (3/3)
Thread on the Plastic Nut and
hand-tighten to seal the cable cable
gland.
8All specifications are subject to change without notice
Copyright © 2023 Verkada Inc. All rights reserved.
Installation
Connect
Verkada Inc. 406 E. 3rd Ave, San Mateo, CA 94401
For easy registration and setup, scan the QR code on the back of the product.
If you prefer to manually register your product, please proceed to:
verkada.com/start
Scan the QR code
on the product with
a phone or tablet to
easily register it to your
Command account.
9All specifications are subject to change without notice
Copyright © 2023 Verkada Inc. All rights reserved.
Installation
Secure
Verkada Inc. 406 E. 3rd Ave, San Mateo, CA 94401
Adjust the speaker to desired angle and
then fully tighten both fasteners (using #2
Phillips driver).
Please note: Ensure the speaker horn is
angled downwards to avoid water
accumulation inside the speaker.
Align speaker with mount bracket.
Insert fasteners (included in the package)
and hand tighten screws on both sides.
Adjust the speaker to desired angle,
and fully tighten both fasteners using
a #2 Phillips driver.
Align speaker with mount bracket.
Insert fasteners (included in the
package) and hand-tighten screws
on both sides.
Please note: Ensure the speaker’s horn
is angled downwards to avoid water
accumulation inside the speaker.
10 All specifications are subject to change without notice
Copyright © 2023 Verkada Inc. All rights reserved.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Manuales populares de Bocina de otras marcas
Elk Products
Elk Products 45 Manual de usuario
Valcom
Valcom V-1050C Manual de usuario
Cooper Wheelock
Cooper Wheelock DB3 Series Manual de usuario
Altec Lansing
Altec Lansing 811B HF HORN Manual de usuario
RF Elements
RF Elements UltraHorn CC Series Manual de usuario
Edwards Signaling
Edwards Signaling 869DSTR-G1 Series Instrucciones de montaje
