Vent-Axia SVARA Manual de usuario

A product by

Instruction Manual

Fully automatic fan with built in app control

SVARA

009-500032-B

EN Fully automatic fan with built in app control

FR Ventilateur automatique, contrôlé par

une application

NL Automatische ventilator met app-sturing

DE Automatische App-gesteuerter Bad- und

Küchenventilator

EN Important Information 4

Installation and Wiring Instructions 5-13

Pin Code for app 44

Accessories 45

FR Informations importantes 14

Manuel d’installation et d’utilisation 15-23

Code Pin pour app 44

Accessoires 45

NL Belangrijke informatie 24

Gebruiks- en installatiehandleiding 25-33

Pincode voor app 44

Toebehoren 45

DE Wichtig 34

Benutzer - und Installationshandbuch 35-43

Pin-Code zur Appsteuerung 44

Zubehör 45

Article reference / Référence d’article / Artikelnummer / Artikelnummer

BE/FR 1001000308 - NL/DE 8000000001

4Operating and installation instructions

DO NOT install this product in areas where the

following may be present or occur:

• Excessive oil or a grease laden atmosphere.

• Corrosive or flammable gases, liquids or vapours.

• Ambient temperatures are outside 5-50°C.

• Possible obstructions which would hinder the access or

removal of the Fan.

SAFETY AND GUIDANCE NOTES

A. All wiring to be in accordance with the current I.E.E.

Regulations, or the appropriate standards of your

country and MUST be installed by a suitably qualified

person.

B. The Fan should be provided with a local isolator switch

capable of disconnecting all poles, having a contact

separation of at least 3mm.

C. Ensure that the mains supply (Voltage, Frequency, and

Phase) complies with the rating label.

D. The Fan should only be used in conjunction with the

appropriate Vent-Axia products.

E. The fan should only be used in conjunction with fixed

wiring.

F. The Fan should not be used where it is liable to be

subject to direct water spray for prolonged periods of

time.

G. Where ducted Fans are used to handle moisture-laden

air, a condensation trap should be fitted. Horizontal

ducts should be arranged to slope slightly downwards

away from the Fan.

H. This appliance is not intended for use by young children

or infirm persons without supervision.

I. Young children should be supervised to ensure that they

do not play with the appliance.

J. The exterior grille should be at least 2.3m above the

ground to prevent people from being able to access

moving parts. If the external grille is positioned

between 0-2.3m from the ground, please use the Vent-

Axia wall kit to ensure people cannot access the fans

impeller from the outside.

Important: READ THESE INSTRUCTIONS BEFORE COMMENCING THE INSTALLATION

5Operating and installation instructions

Installer information

Installation Preparation

• Loosen the motor unit by grasping it as shown in Figure

(A), prise off the motor unit by leaveraging against the cap

with your knuckles. Ensure that you have the motor unit in a

secure grip so you do not drop it when it loosens.

• Then loosen the wall frame by using a screwdriver pressing

the lock button as shown in Figure (B) then remove the

cover from the wall frame according to figure (C).

Installation

5 mm

Ø 110 mm

New Installations

New installations require holes using a Ø110 mm hole saw

(Figure D).

6Operating and installation instructions

E. F.

R75

45°

H. I.

• The fan’s wall seal has a short spigot which fits inside the

Ø100 mm pipe. Make sure when mounting to adapt the

length of the wall pipe so it does not push back the wall seal

so the fan impeller cannot rotate. Always customise a wall

pipe, existing or new, so it ends about 5 mm inside the wall

surface where the fan is to be installed. The wall frame with

its seal is prepared with 5 cable entry points (Figure F) for

concealed electrical connection or surface-mounted cable

using the dimension shown in Figure G.

• Make sure that the gasket is properly installed on the

wall frame, place it in the appropriate place and centre

it in the pipe.

• The wall frame can be offset horizontally by placing a

spirit level on its support points (Figure H and I).

Installer information

• Vent-Axia wall kits and external grilles are available as

accessories. (Figure E).

Use ageing-resistant sealant

to seal around cables that are

laid through the wall seal.

7Operating and installation instructions

R75

30°

65°

95°

Always use a qualified electrician

All electrical connections 100-240V must be performed by a

qualified electrician. Any electrical work on the product must

utilise a voltage break.

Electrical connection can be made according to the wiring

diagram on page 6-7 and the fan is suitable for connection

to either 100-240VAc or 12VDC.

NOTE: The internal cable route must be as indicated as

figures K/K1 (240VAC) and L (12VDC) to prevent the cable

blocking the locator’s for the motor assembly.

• Mark the three attachment points for the appropriate

screws to the substrate (Figure J). Tighten the screws so

that gasket seals against the wall.

K1.

100-240 V AC

connection

12 V DC connection

Installer information

8Operating and installation instructions

NOTE! The integrated all-pole switch S only

functions at 100-240VAC wiring.

Svara auto:

100-240VAC 50 / 60Hz

Continuous trickle speed ventilation, automatic boost

at elevated humidity levels, and via the integrated light

sensor. Possibility to start/stop via manual switch T.

Svara on/off operation through remote

switch, with overrun:

(Can be combined with backdraft shutter)

100-240VAC 50 / 60Hz

Must be selected via Vent-Axia Connect App.

Start / stop via manual switch T.

(start = max. RPM, stop = 15 minutes run-on time)

Svara humidity controlled:

(Can be combined with backdraft shutter)

100-240VAC 50 / 60Hz

Must be selected via Vent-Axia Connect App.

Trickle setting, automatic start / stop

on changes in humidity levels. Possibility to start/stop via

manual switch T.

(start = max. RPM, stop = 15 minutes run-on time)

Svara on/off operation through remote

switch:

(Can be combined with backdraft shutter)

100-240VAC 50 / 60Hz

Must be selected via Vent-Axia Connect App.

Start / stop via manual switch L.

NOTE: With T switch activated, the fan always

returns to max. speed after contact via app.

Any changes are only activated when the T input

is switched off and the run-on time has elapsed.

ELECTRICAL CONNECTION 100-240VAC

NOTE! Wiring of 100-240VAC must be

performed by a qualified electrician.

Installer information

Bluetooth LE: -12dBm EIRP (63µW), nominal 2450MHz.

Radio Equipment Directive (RED)

Bluetooth LE: -12dBm EIRP (63μW), nominal 2450MHz

Vent-Axia hereby assure that this type of Bluetooth radio

equipment complies with RED Directive 2014/53 / EU.

The full text of the EU Declaration of Conformity can be

found at the following URL: www.vent-axia.nl, www.vent-

axia.be, www.vent-axia.de, www.vent-axia.fr.

9Operating and installation instructions

Connection of 100-240VAC

and 12VDC can not be done

simultaneously (Figure N).

NOTE! 12VDC voltage must not exceed

between 10 - 13,6VDC.

NOTE! For 12VDC always use switches

intended for direct current, C.

N. O.

No 100-240V wiring may

penetrate the electronics

portion (Figure O).

Svara auto:

12VDC (switch C always)

Continuous trickle ventilation, automatic boost at elevated

humidity levels, and via the integrated light sensor.

Svara on/off operation through remote

switch:

(Can be combined with backdraft shutters)

12VDC

Must be selected via Vent-Axia Connect App.

Start / stop via manual switch C.

Svara humidity controlled:

(Can be combined with backdraft shutters)

12VDC (switch C always)

Must be selected via Vent-Axia Connect App.

Trickle setting, automatic start / stop

on changes in humidity levels.

ELECTRICAL CONNECTION 12VDC

Installer information

10 Operating and installation instructions

Mounting the cover on the wall frame

• The fan is double insulated and must not be earthed. When the electrical connection is made place the cover back over

the wall frame fitted into the housing hole (Figure P).

• Next, fold the cover over the wall frame (Figure Q).

Q. R.

• Ensure the catch the screwdriver is pointing to (Figure R) engages properly.

• Make sure that the cover is firmly seated in the hook on the wall frame and latch by pulling a bit of cover.

• Finally put the motor unit in place (Figure S). Be careful when fitting motor unit, the impellor can be damaged if the unit is

forced in at an angle.

• A distinct ’click’ sound confirms that the device is in place, check that the integrated On switch works freely before turning

on according to (Figure T).

Installer information

Otros manuales para SVARA

Tabla de contenidos

Idiomas:

Otros manuales de Admirador de Vent-Axia

Vent-Axia

Vent-Axia Lo-Carbon Revive Series Instrucciones de montaje

Vent-Axia

Vent-Axia SUPRA 100 B Instrucciones de montaje

Vent-Axia

Vent-Axia Slimpak EC Series Instrucciones de montaje

Vent-Axia

Vent-Axia QP Series Instrucciones de montaje

Vent-Axia

Vent-Axia MULTIVENT MV250 Instrucciones de montaje

Vent-Axia

Vent-Axia MFQ35014 Instrucciones de montaje

Vent-Axia

Vent-Axia Lo-Carbon VA100 SELV Series Instrucciones de montaje

Vent-Axia

Vent-Axia Lo-Carbon SOLO Plus SELV Series Instrucciones de montaje

Vent-Axia

Vent-Axia NBR dMEV C 100 T Instrucciones de montaje

Vent-Axia

Vent-Axia Lo-Carbon VA150P Instrucciones de montaje

Vent-Axia

Vent-Axia ACH100B Instrucciones de montaje

Vent-Axia

Vent-Axia HR300RW6 Guía del usuario

Vent-Axia

Vent-Axia Sentinel Instrucciones de funcionamiento

Vent-Axia

Vent-Axia Lo-Carbon Tempra P Instrucciones de montaje

Vent-Axia

Vent-Axia Silhouette 100T Instrucciones de montaje

Vent-Axia

Vent-Axia Centrif Duo Instrucciones de montaje

Vent-Axia

Vent-Axia Lineair LINEAIR100 B Instrucciones de montaje

Vent-Axia

Vent-Axia Lo-Carbon Scala Plus Series Instrucciones de montaje

Vent-Axia

Vent-Axia GALAXY GDB Series Instrucciones de montaje

Vent-Axia

Vent-Axia Lo-Carbon PureAir Home Series Instrucciones de montaje

Vent-Axia

Vent-Axia HR205 Guía del usuario

Vent-Axia

Vent-Axia Lo-Carbon Quadra SELV Series Instrucciones de montaje

Vent-Axia

Vent-Axia 45 90 49 Manual de usuario

Vent-Axia

Vent-Axia 9” DESK FAN Manual del propietario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje