VENGEANCE HYPERION FPV RACER Manual de usuario
280 Size
FPV Racer
●Fully Assembled: No building or firmware loading
necessary!
●On-Screen Display (OSD): Program or set up your
Vengeance on-the-y, no computer needed.
●In-Flight-Adjustable Single-Axis Camera Gimbal, Self-
leveling during ight.
●Vibration Dampened Second-Camera Mount.
●Robust, Pure Carbon-Fiber Frame with Carbon
Exoskeleton Reinforcements.
●Stress-Flex Designed to Withstand Impacts, Mass
centralized for high-rate turning.
●Black-Anodized, High-Strength CNC Aluminum Boom
Mounts.
●Tough, Translucent Polymer Landing Legs with Built-in
Directional Red-Green LED.
●8°Forward-Tilt Motor Mounts for Aerodynamic
Efciency and Top Speed Performance.
●Four 2204, 2300Kv High-Output Brushless Motors.
●Custom Compact BL-Heli 20A Motor Controllers (ESC).
●Visual LED Flight Mode Indicator. Easy to conrm your
ight mode.
●Pre-loaded with Three Flight Modes: Normal, Altitude
Hold, or Acro Mode.
●NAZE Spec 32 Bit Flight Controller 7DOF (with
BMP sensor).
●Altitude Hold via Integrated Barometric Pressure
Sensor (BMP).
●3S and 4S Battery Compatible. Hyperion G6 HV
LiPo Suggested.
●5.8GHz Auto-Scan 40CH Video Transmitter
(VTX) w/ Race Band VTX selectable for either
25mw/200mw output.
●Tuned 5.8GHz CloverLeaf Skew-Planar Antenna.
●Plug-n-Play Ready for Optional GPS modules.
●Built-in Low-voltage Audible Alarm.
●Compatible with Single Wire* or Traditional
Receivers (*S-Bus, Horizon Spektrum™ Satellite, or
Hyperion Compatible receivers).
●Box includes Carry Handle and Foam Racer
Cradle + Parts Holder, for service as eld case.
●One Set 6x4 CC/CCW Propellers Included.
••••••••••
••••••••••
••••••••••
○ Specications
○ Length：216mm Channels：6～8ch Motors：Hyperion 2204-2300kVㄈ
○ Width：255mm Camera：600tvl 1/3" CMOS Camera ESC：BL Heli 20A
○ Diagonal Base：280mm
VTX：5.8Ghz 25-200 0mW selectable w/ 40Ch's
Propellers：6040 CW & CCW
○ Weight：435g（w/o battery） Battery：3~4S Compatible Controller：Naze32 w/ OSD & Altitude Sensor
280mm
212mm
255mm
113mm
229mm
81mm
216mm
33.2mm
186mm
1
▲
BL Heli 20A 2S~4S ESC ×4 ▲5.8GHz Cloverleaf RHCP
Antenna (RP-SMA)
▲5 . 8 G H z S e l e c t a b l
e 25mW / 200mW Video
Transmitter
▲Flight Controller with OSD, and Altitude
Sensor
▲LED Landing Gear
PCB (Red)
▲LED Landing Gear
PCB (Green)
▲Gimbal Mount
Bracket
▲Vengeance
Gimbal Motor
with Sensor (1-
axis Pitch)
▲Camera Mount
Bracket
▲1/3" 600tvl CMOS
Camera
▲Rear Frame Standoff
9mm ×2
▲Rear Frame Standoff
10mm ×2
▲
Hyperion Silicon
Dampeners Soft ×5
▲Hyperion 2204-2300kv Brushless Motor CW ×2
Hyperion 2204-2300kv Brushless Motor CCW ×2
▲
Eight Degree Forward Tilt
Motor Mounts ×4
▲Vengeance Translucent Landing Gear×4
▲
Main Frame Mounting
Clamps ×4
▲
Motor Mounting
Clamps ×4
▲
Front Arm Reinforcement
Clamps ×2
▲
6x4 CW + CCW Prop Set (Black)
▲
6x4 CW + CCW Prop Set (Orange)
▲Rear Arms Tubes 15×83mm ×2▲Front Arm Tubes 15×73mm ×2
▲
Vengeance Carbon Fiber Frame Kit
Main Carbon Fibre Frame
Camera Mounting Plate
Left / Right Reinforcement Plate Lower Front Reinforcement Plates
Lower Main Carbon Fibre Frame
Lower Rear Reinforcement Plates
VTX Mounting Plate
2
••••••••••
13
24
19mm
16mm
19mm
The Vengeance's unique motor mount design allows for superb
forward flight and cornering performance. Please note that during
installation that you install each arm in the proper location and the angle
of motors and motor rotation corresponds to the picture enclosed.
▲Counterclockwise
Rotation >>>> Motor
Rotation Indicators.
▲Clockwise Rotation
<<<< Motor Rotation
Indicators.
1.Motor & Arm
↑1-4 Motor Rotation Chart.
LED Landing Gear Assembly Chart→
Motor Mount Assembly ↗
Direction Chart.
M3×6mm Hex Screws
Eight Degree Forward
Tilt Motor Mounts
Hyperion 2204-2300kv
13 24
Motor mount arrows
indicated forward position
of the motor. →
3
M3 x 10mm Self-tapping Screw
Translucent Landing Gear
VTX Mounting Plate
5.8GHz Selectable 25mW / 200mW
Video Transmitter
Heat shrink tube
Double Side Adhesive Tape
LED Landing Gear PCB
BL Heli 20Amp ESC 2~4S
M2.5 × 10mm Hex Screw
M2.5 × 16mm Hex Screw
Motor Mount Arm Clamps
15mm Arm Tubes
Arm 1 & 3 use 15×73mm
Arm 2 & 4 use 15×83mm
2.VTX Assembly
4
Rear Frame Standoff 9mm
Rear Frame Standoff 10mm
M2.5×16mm Hex Screws
M2.5×4mm
Hex Screws
M2.5×10mm
Hex Screws
NOTE: use the "Video Out" plug
to connect to your VTX. "Video
IN" plug is used to connect to
the Camera.
M2.5×14mm
Hex Screws
M2.5×8mm
Hex Screws
M2.5 Self Locking Nut
M2.5 Self Locking Nut
Front Arm Reinforcement Clamps
Lower Front Reinforcement Plates
Lower Rear
Reinforcement
Plates
Lower Main
Carbon Fibre
Frame
Frame Mount
Clamps
Frame Mount
Clamps
Flight Controller
M2.5×8mm
Hex Screws
M2.5×8mm
Hex Screws
M2.5×8mm
Hex Screws M2.5×10mm
Hex Screws
M2.5×14mm
Hex Screws
M2.5×14mm
Hex Screws
M2.5×10mm
Hex Screws
M2.5×10mm
Hex Screws
M2.5×4mm
Hex Screws
M2.5×14mm
Hex Screws
3.Main Frame Assembly
5
M1
M2
M3
M4
←Make sure that the landing gear plate is 90° to the main
frame plate.
↑Once you have conrmed the landing gear plate is 90°
to the main frame plate you can then fasten the clamp
screw.
←
Before Flying make sure your wires are
correctly plugged into the proper color
receptacle. Insert the LED Landing Gear
Light Indicator in the plug.
90° to Main Frame Plate
Positive ESC Power Supply Negative ESC Power Supply
PWM Throttle Signal Wire
4. Main Arm Assembly
6
Camera Mounting Plate
M2.5×4mm
Hex Screws
M2.5×6mm
Hex Screws
Vengeance Silicone
Dampeners (Soft) ×5
Left Reinforcement Plate
Right Reinforcement Plate
Main Carbon Fibre Frame
M2.5×4mm
Hex Screws
Gimbal Mount Bracket
1/3" 600tvl CMOS Camera
Vengeance Gimbal Motor
with Sensor (1-axis Pitch)
5. Camera Mounting Assembly
M2.5 Self Locking Nut
M2.5×6mm
Hex Screws
M2.5×6mm
Hex Screws
M2.5×6mm
Hex Screws
M2.5×6mm
Hex Screws
M2.5×4mm
Hex Screws
M2.5×4mm
Hex Screws
7
Complete!!
6. Frame Final Assembly
••••••••••
13
24
↑M1-M4Motor Rotation and Arm
Placement Chart.
M2.5×8mm
Hex Screws
5.8GHz Cloverleaf RHCP
Antenna (RP-SMA) #1 Propeller rotation
#3 Propeller rotation
#2 Propeller rotation
#4 Propeller rotation
#1 Nut rotation
#3 Nut rotation
#2 Nut rotation
#4 Nut rotation
NOTE: Do not power on the
the VTX without installing
the antenna rst. Failure to
do so may harm the VTX
and cause it to fail.
8
Tabla de contenidos
