Velleman K8065 Manual de usuario

POCKET AUDIO GENERATOR

K8065

ILLUSTRATED ASSEMBLY MANUAL H8065IP-1

Total solder points: 109

Difficulty level: beginner 1 2 3 4 5 advanced

Great littlegadget forservice

repair,testing,education,etc...

Features:

 Microprocessor technology

 Digital waveform generation

Specifications:

 Sine wave: 50Hz, 100Hz, 1KHz, 10KHz, 20KHz

 Burst: 50Hz, 100Hz, 1KHz

 Burst mode: 20ms ON, 500ms OFF

 Noise: 32-bit digital noise

 Output level (10Kohm): 0 to 775mV (0dB)

 Outputs: 2 x RCA (cinch)

 Power supply: 2 x CR2016 or 2 x CR2025 battery (excl.)

 Dimensions: 86 x 50 x 25mm (3.4" x 2.0" x 1.0")

Features & Specifications

Assembly hints

1. Assembly (Skipping this can lead to troubles ! )

Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.

1.1 Make sure you have the right tools:

• A good quality soldering iron (25-40W) with a small tip.

• Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and will

protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning.

• Thin raisin-core solder. Do not use any flux or grease.

• A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they

cannot fly towards the eyes.

• Needle nose pliers, for bending leads, or to hold components in place.

• Small blade and Phillips screwdrivers. A basic range is fine.

For some projects, a basic multi-meter is required, or might be handy

1.2 Assembly Hints :

⇒Make sure the skill level matches your experience, to avoid disappointments.

⇒Follow the instructions carefully. Read and understand the entire step before you perform each operation.

⇒Perform the assembly in the correct order as stated in this manual

⇒Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.

⇒Values on the circuit diagram are subject to changes.

⇒Values in this assembly guide are correct*

⇒Use the check-boxes to mark your progress.

⇒Please read the included information on safety and customer service

* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’ on a separate leaflet.

Assembly hints

1.3 Soldering Hints :

1- Mount the component against the PCB surface and carefully solder the leads

2- Make sure the solder joints are cone-shaped and shiny

3- Trim excess leads as close as possible to the solder joint

REMOVE THEM FROM THE TAPE ONE AT A TIME !

AXIAL COMPONENTS ARE TAPED IN THE CORRECT

MOUNTING SEQUENCE !

You will find the colour code for the resistances and the LEDs in the HALG

(general manual) and on our website: http://www.velleman.be/common/service.aspx

 R3 : 20K (2 - 0 - 0 - 2 - 1)

 R14 : 10K (1 - 0 - 0 - 2 - 1)

4. Metal film resistors

R...

Construction

 D1 : 1N4148

2. Diode. Watch the polarity !

D...

CATHODE

 IC1 : 14P

6. IC socket, Watch the

position of the notch !

 J1

 J2

1. Jumper

 C1 : 15pF (15)

 C2 : 15pF (15)

 C3 : 100nF (104)

 C5 : 560pF (561)

 C6 : 10nF (103)

 C7 : 15nF (153)

7. Capacitors.

C...

 RV1 : 1K

8. Resistor trimmer

RV1

 ZD1 : 5V1

3. Zenerdiode. Watch the

polarity !

ZD...

CATHODE

 R17 : 1K5 (1 - 5 - 2 - B)

 R19 : 1K (1 - 0 - 2 - B)

5. Resistors

R...

Construction

 C4 : 47µF

14. Electrolytic Capacitor.

Watch the polarity !

C...

 SW1

9. Slide switch.

 E1

10. Battery holder

 T1 : BC547C

 T2 : BC547C

 T3 : BC557C

11. Transistors

 R1 : 20K (2 - 0 - 0 - 2 - 1)

 R2 : 20K (2 - 0 - 0 - 2 - 1)

 R4 : 20K (2 - 0 - 0 - 2 - 1)

 R5 : 20K (2 - 0 - 0 - 2 - 1)

 R6 : 20K (2 - 0 - 0 - 2 - 1)

 R7 : 20K (2 - 0 - 0 - 2 - 1)

 R8 : 20K (2 - 0 - 0 - 2 - 1)

 R9 : 10K (1 - 0 - 0 - 2 - 1)

 R10: 10K (1 - 0 - 0 - 2 - 1)

 R11: 10K (1 - 0 - 0 - 2 - 1)

 R12: 10K (1 - 0 - 0 - 2 - 1)

 R13: 10K (1 - 0 - 0 - 2 - 1)

 R15: 10K (1 - 0 - 0 - 2 - 1)

12. Vertical metal film resistors

R...

 R16 : 1K5 (1 - 5 - 2 - B)

 R18 : 1K5 (1 - 5 - 2 - B)

13. Vertical resistors

R...

 X1 : 20MHz

15. crystal

X...

Max. 8mm

 LD1 : 3mm Red

 LD2 : 3mm Red

 LD3 : 3mm Red

 LD4 : 3mm Red

 LD5 : 3mm Red

COLOR= 2...5

LD...

CATHODE

Construction

16. LEDs. Watch the polarity!

A B

 SW2 : KRS0611

 Mount the push button at the solder side of the

PCB !

SW...

17. Push button.

 IC1 : VK8065

(programmed PIC16F630)

18. IC. Watch the position of the notch!

solderside

Axis of a

rotary switch.

 Close the enclosure with the 2 supplied screws.

 Drill two Ø3mm holes in the housing according to figure 1.0.

The RCA cable will run through them.

 Solder the signal wires or the RCA

cable to the 'OUT' terminal on the PCB

(see figure 2.0).

 Solder the shielding of the RCA cable

to the 'GND' terminal on the PCB (see

figure 2.0).

19. Assembly

Assembly

3mm drill.

Fig. 1.0

Fig. 2.0

shielding

signal

GND

Assembly

 Insert two CR2025 or two CR2016 batteries into the battery holder.

Mind the polarity!, see figure 3.0

 Mount all parts and close the housing by means of the enclosed

screws, see figure 4.0.

 BEWARE: Do not forget to feed the RCA

cable through the two holes in the housing.

Fig. 4.0

Fig. 3.0

Tabla de contenidos

Otros manuales de Equipo de prueba de Velleman

Velleman

Velleman VTTEST11 Manual de usuario

Velleman

Velleman VTTEST3 Manual de usuario

Velleman

Velleman HPG1MK2 Guía de configuración rápida

Velleman

Velleman HQ Power HQLE10026 Manual de usuario

Velleman

Velleman Personal Scope HPS5 Manual de usuario

Velleman

Velleman Personal Scope HPS50 Guía

Velleman

Velleman VTTEST13 Manual de usuario

Velleman

Velleman EVT04 Manual de usuario

Velleman

Velleman HPS140i Manual de usuario

Velleman

Velleman AVM52ERT Manual de usuario

Velleman

Velleman BATTEST2 Manual de usuario

Velleman

Velleman PCSU200 Manual de usuario

Velleman

Velleman BATTEST2 Manual de usuario

Velleman

Velleman EDU06 Manual de usuario

Velleman

Velleman VTTEST7 Manual de usuario

Velleman

Velleman EDU08 Manual de usuario

Velleman

Velleman DVM1356 Manual de usuario

Velleman

Velleman PCS500 Manual de usuario

Velleman

Velleman WFS210 Manual de usuario

Velleman

Velleman VTLAN4 Manual de usuario

Velleman

Velleman DEM800 Manual de usuario

Velleman

Velleman VTTEST30 Manual de usuario

Velleman

Velleman VTTEST2 Manual de usuario

Velleman

Velleman ILMA001 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario

Velleman k8065 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas