Velleman CU2200 Manual de usuario

CU2200

WIRELESS SMS ALARM MESSENGER

DRAADLOZE SMS-ALARMMELDER

SYSTÈME DE MESSAGERIE D'ALARME SMS SANS FIL

SISTEMA DE ALARMA INALÁMBRICO POR MENSAJES SMS

DRAHTLOSER SMS-ALARM

USER MANUAL 2

GEBRUIKERSHANDLEIDING 13

NOTICE D’EMPLOI 24

MANUAL DEL USUARIO 35

BEDIENUNGSANLEITUNG 46

V3_03

CU2200 v3-03

23.10.2014 ©Velleman nv

User manual

1. Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could

harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should

be taken to a specialized company for recycling. This device should be returned to your distributor or

to a local recycling service. Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for buying a VELLEMAN product! The CU2200 is equipped with a very reliable Siemens 16 bit MCU and

can be used for numerous applications (except for medical and aerospace applications) such as industrial

equipment or area monitoring, data capturing, home or car security… Please read the manual thoroughly before

bringing this device into service. If the device was damaged in transit, do not install or use it and contact your

dealer.

2. Safety Instructions

Keep the device away from children and unauthorised users.

Risk of electroshock when opening the cover. Touching live wires can cause life-threatening

electroshocks. Do not open the housing yourself. Have the device repaired by qualified personnel.

There are no user-serviceable parts inside the device. Refer to an authorized dealer for service and/or

spare parts.

3. General Guidelines

Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.

Dry location use only. Keep this device away form rain, moisture, splashing and dripping

liquids. Never put objects filled with liquid on top.

Keep this device away from dust and extreme temperatures.

Protect this device from shocks and abuse. Avoid brute force when operating the device.

Familiarise yourself with the functions of the device before actually using it.

All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the

device is not covered by the warranty.

Only use the device for its intended purpose. Using the device in an unauthorised way will void the warranty.

Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the

dealer will not accept responsibility for any ensuing defects or problems.

Keep this manual for future reference.

Do not use outside the technical specifications (see §12).

4. Features

8 x alarm inputs (opto-isolated)

1 x relay output

4 x programmable mobile phone numbers for alarm SMS

4 x programmable phone numbers for alarm call

3 alarm alert modes: SMS, phone dial or SMS and phone dial

automatic power supply voltage level check

automatic reporting on low-power voltage level

programmable SMS alarm text message

GSM dual band support

each event sends its own text message

remote arming or disarming

easy installation

functions: text messages, administration, input and output are all programmable through your mobile phone

access control: by password and mobile phone caller ID

advantages

ono mobile phone is needed on-site

ono alarm panel is needed on-site

ono more constant telephone line charges

ono more on-site maintenance

osecure self-contained unit

CU2200 v3-03

23.10.2014 ©Velleman nv

5. Overview

OUT1

Relay output jumper

1 2 3

▪▪▪

1-2 short NC

2-3 short NO (default)

POW

7~12VDC power input

GND

ground

AD1, AD2

these inputs are not supported on the CU2200

IN1, IN3, IN4,

IN5, IN6, IN7, IN8

12VDC alarm input, 7~15mA

GND

common ground opto-coupled

IN2+, IN2-

7~12VDC input

OUT1

relay output, max. 1A, 24VDC, 1A, 120VAC, NC/NO (selected by jumper on board)

Alarm Input

12VDC, 7 ~ 15m, Opto-isolated Inputs (1kΩ Input

Resistance)

24VDC, resistor 1 ~ 2,2kΩ should be used in serial

(a) IN1, IN3, IN4, IN5, IN6, IN7, IN8

Alarm Input: DC12V 7 ~ 15mA, GND: Common Ground

(b) IN2+, IN2-

IN2+:DC5 ~ 12V

IN2-: Ground [It must NOT be common to the GND of the

board]

Relay Output

OUT1, OUT2, OUT3:

Max. 1A, 24VDC / 1A, 120VAC

NC/NO (selected by jumper on board)

Note: OUT2 and OUT3 are not available

on CU2200

6. Connection

RS232 pin assignment

9600bps, 8bit, no parity, 1 stop

pin 2 RxD

pin 3 TxD

pin 5 GND

CU2200 v3-03

23.10.2014 ©Velleman nv

LED 1 –green status LED

Rapid flashing on/off

GSM module normal operation

Flashing on/off

GSM network connection problem

Reason:

Antenna not connected

No SIM card

Defective SIM card

Defective GSM module

LED 2 –red network LED

Normal operation

Flashing on/off

Searching GSM network

Connecting to network

Receiving SMS messages

Sending SMS messages

Phone dialling

Sound Monitoring

The CU2200 automatically picks up any phone call after eight rings. By connecting a microphone to the

CU2200, you will be able to hear all actions in the room.

7. Quick Setup

Press the yellow button so as to eject the card caddy. Insert

the SIM card with the contacts facing down. Press the card

back into the CU2200.

Attention: “asking for PIN code” must be deactivated

on SIM card first, before use with CU2200! (See

instructions of your mobile phone).

Connect the 12VDC power supply and wait until the red LED

turns on and the green LED flashes every few seconds.

Send following SMS message to the CU2200 (from another

mobile phone): PWD:1234,STATUS%.

Your mobile phone will receive an SMS reply within 30

seconds reporting the health status.

NOTE: The SIM card in the CU2200 must be activated by a

provider like a regular SIM card in a mobile phone.

Make sure to activate the caller ID service.

8. PC Setup Software [V7.0]

The unit can be programmed by: (A) SMS command via mobile phone

(B) Software via its built-in RS232 port

First check the hardware version of your device via an SMS from your mobile phone. When the SMS was correct

the device will reply with a text message containing the version; if there was an error you will get the message

‘SMS format is error!’. The SMS command depends on the software version:

Software version V5, V6

Software version V7

Command: PWD:XXXX,CHECKV

[SMS message received]

ex: SD41 V5.1_3_B 2008/01/28

V5 is system version or hardware version

CU2200.

Command: PWD:XXXX,CHECKVR%

[SMS message received]

ex: SD41 V7.1_3_B 2010/01/28

V7 is system version or hardware version

CU2200.

Important notes on used PC Software:

Software can be found on the included CR ROM or on the product page on www.velleman.eu.

Software version SMS_ProX.exe (SMS PRO_V5.0) only works with hardware version 5 of the CU2200.

Software version SM41DPRO.exe (SMS PRO_7.0) works with both hardware versions 6 and 7. It is

recommended to use this version when you have a hardware version 6 or 7 device.

Software version SMSPro_Setup_2.2.13_0927.exe only works with hardware version 7. When running

this software, select “basic” at start-up.

The software is developed for multiple platforms; hence it is possible that some of the shown functions

are not accessible or (fully) supported.

Note: it is not possible to upgrade the hardware version of the CU2200.

Copy the program folder to C:\ ,and run “SM41DPRO.exe” under windows.

CU2200 v3-03

23.10.2014 ©Velleman nv

(refer to the numbers on the illustration)

1. Select the COM port of the PC connected to the device.

2. Click [Connect] button to activate the connection between PC and SMS alarm unit.

3. Click [Health Check] or [Parameters 1 or 2(SYSTEM)] to get the internal configuration.

Please refer each setting to the corresponding command described on next pages.

9. Alarm Response Time

The messenger will start the initialization after connection to the power supply. This procedure will take

about 30 seconds.

In case of an alarm, the unit will send an SMS message to the control centre and to 4 pre-programmed

phone numbers. The control centre can be disabled in order for the phone numbers to receive the alarm

10. GSM Network Connectivity

If the GSM network is suddenly inaccessible or disconnected during the SMS sending, the message will

be lost.

When the CU2200 has failed to send the message due to an inaccessible network, the unit will search

for the network and keep sending the SMS when the network has been re-established.

When failing to send SMS messages, the CU2200 will memorize up to 10 messages and send them as

soon as the network is re-established.

11. SMS Command list

a. System setup

New Password Setup

Manual Health Reporting

Serial Number Setup

Control Centre Number & Health Reporting Schedule Setup

Power-Up Message

System Clock Setup

Phone Number Setup

b. alarm setup

Alarm Input Level & Alert Setup

SMS Alarm Message Setup

SMS Message Contents

Commanding the CU2200 to Send SMS Message

Relay Output Control

Relay Output Delay Time

Operating Voltage Low Level Alarm Message

Operating Voltage Low Level Alarm

Arm/Disarm Setup

CU2200 v3-03

23.10.2014 ©Velleman nv

c. System Information Report

Default Setting

System Parameters RESET

System Version Check (hardware version CU2200)

Return Message

System Parameters Report

Manual Health Report

Configure the CU2200 through the command text sent from your mobile phone. Upon reception and

processing, the unit will send a confirmation message to your mobile phone. If the command is incorrect,

the unit will reply SMS format is error!

a. System Setup

New Password Setup

Command: PWD:XXXX,NEWPWD:YYYY%

XXXX

Current password

YYYY

New password (4 digits)

Example:

PWD:1234,NEWPWD:2222%

Default password: 1234

New password: 2222

Manual Health Reporting

Command: PWD:XXXX,STATUS%

[SMS message received]

ST:XXX;T:2005/01/28/13:00;V:XXXX;A1:0000;A2:0000;K1:X;K2:X;K3:X;K4:X;K5:X;K6:X;K7:X;K8:

X;OUT1:Y;OUT2:Y;OUT3:Y;#

Example:

ST:002;T:2005/01/28/13:00;V:8.15;A1:0000;A2:0000;K1:X;K2:X;K3:X;K4:1;K5:1;K6:X;K7:X;K8

:X;OUT1:1;OUT2:1;OUT3:1;#

Unit serial number

XXX

ASCII code

Unit internal clock

XXXX

Year/month/day/time

Operating voltage

XXXX

Alarm channel 1

K1:0 means closed

K1:1 means open

K1 ~ 8

Alarm channel 1 ~ 8

OUT1

Relay output 1

OUT1:0 means open

OUT1:1 means closed

OUT1 ~ 3

Relay output 1 ~ 3 (outputs 2 and 3 are

displayed but not available)

Serial Number Setup

Command: PWD:XXXX,SN:YYY%

XXXX

Password

YYYY

Serial number (0-999)

Example:

PWD:1234,SN:268%

Password: 1234 (default)

Serial number set into the unit: 268 (default: 000)

Control Centre Number & Health Reporting Schedule Setup

These two values are configured by one single command.

(1) The control centre number is the phone number receiving the periodic report and regular report.

Besides the periodic report on schedule (command 5: power-up message), report of any command will

be sent to this number in addition to the mobile phone number sending the command. Maximum 2

control centres can be defined.

Command: PWD:XXXX,CTRZ:YYYYYYYYYYY,MM#%

XXXX

Password

Control centre number (max. 2 centres)

1 means 1st centre number

2 means 2nd centre number

YYYYYYYYY

Phone number in control centre

Period code of automatic scheduled health report

Example:

PWD:1234,CTR1:123456789,04#%

Password: 1234

Reporting health status every hour (refer to the reference table below)

(2) The periodic health report and any command from another mobile phone will be reported to the

first control centre with number 123456789.

CU2200 v3-03

23.10.2014 ©Velleman nv

Reference table for the automatic scheduled health report

No automatic report

Every 6 hours

Every 5 minutes

Every 12 hours

Every 15 minutes

Every day (08h00)

Every 30 minutes

Every odd day (08h00)

Every 1 hour

1st, 7th, 14th, 21st, 28th day (08h00)

Every 2 hours

1st, 15th day (08h00)

Every 3 hours

1st day of each month (08h00)

The CU2200 automatically reports the unit’s health status on a pre-defined schedule via an SMS

message.

[SMS message received]

ST:XXX;T:2006/10/08/06:15;V:XXXX;A1:0000;A2:0000;K1:X;K2:X;K3:X;K4:X;K5:X;K6:X;K7:X;K8:

X;OUT1:1;OUT2:1;OUT3:1;#

Unit serial number

XXX

ASCII code

Unit internal clock

XXXX

Year/month/day/time

Operating voltage

XXXX

Alarm channel 1

K1:0 means closed

K1:1 means open

K1 ~ 8

Alarm channel 1 ~ 8

OUT1

Relay output 1

OUT1:0 means open

OUT1:1 means closed

OUT1 ~ 3

Relay output 1 ~ 3

Example:

ST:001;T:2005/01/27/12:00;V:8.14;A1:2312;A2:2131;K1:1;K2:0;K3:0;K4:1; O:1#

Unit serial number

001

Unit internal clock

Date: 27 Jan 2005, time: 12h00

Operating voltage

8.14VDC

Alarm channel 1

Open

Alarm channel 2

Closed

Alarm channel 3

Closed

Alarm channel 4

Open

Relay output 1

Power-Up Message

Whenever the unit is powered up, it will automatically send RESTART! to the control centre.

System Clock Setup

Command: PWD:XXXX,TIME:AABBCCDDEE%

XXXX

Password

AABBCCDDEE

Year/month/day/hour/minute

Example:

PWD:1234,TIME:0602031327%

Password: 1234

Clock: 3 Feb 2006, 13h27

Phone Number Setup

Command: PWD:XXXX,ALMNU1:ZZZZZZZZZZZ,2:ZZZZZZZZZZZ,3:ZZZZZZZZZZZ,4:ZZZZZZZZ

ZZZ,5:ZZZZZZZZZZZ,6:ZZZZZZZZZZZ,7:ZZZZZZZZZZZ,8:ZZZZZZZZZZZ#%

XXXX

Password

ZZZZZZZZZZZ

Phone number

Example 1:

PWD:1234,ALMNU1:12345678,2:36925814712,3:159357456,4:951753654,5:741852963,6:45678

9123,7: 369874123,8:125478963#%

Password

1234

When the alarm is triggered, an SMS message is sent to following

numbers:

N° 1

12345678

N° 2

36925814712

N° 3

159357456

N° 4

951753654

N° 5

741852963

N°6

456789123

N°7

369874123

N°8

125478963

CU2200 v3-03

23.10.2014 ©Velleman nv

Example 2:

PWD:1234,ALMNU1:NUL,3:NUL#%

Password

1234

With example 1, following numbers have been cancelled:

N° 1

12345678, not made

N° 2

36925814712, retained

N° 3

159357456, not made

N° 4

951753654, retained

b. Alarm Setup

Alarm Input Level & Alert Setup

Command: PWD:XXXX,ALMLEVELR:X,YY,ZZZZBBBB,NNN%

XXXX

Password

Alarm channel number

0 means disabled

1 means closed triggers alarm

2 means open triggers alarm

3 means both closed and open triggered alarm

00 means alarm not reported to control centre

10 means alarm reported to control centre 1

01 means alarm reported to control centre 2

11 means alarm reported to control centre 1 and 2

ZZZZBBBB

Selection of the alarm phone dial and alarm SMS

0 means no alarm report

1 means SMS only

2 means phone dial only => (Phone dial not available)

3 means SMS first, then phone dial =>(Phone dial not available)

1st

2nd

3rd

4th phone number

5th

6th

7th

8th phone number

NNN

Relay output control

0 means no relay output control

1 means relay output triggered by alarm

1st

2nd

3rd relay output

(2nd and 3rd relay output not available)

Example 1:

PWD:1234,ALMLEVEL2:1,01,10000000,100%

Password

1234

Alarm channel 2

Once the input is closed, the alarm will be triggered

Control centre 2 will be reported by SMS

Phone number 1

Phone number 2

Phone number 3

Phone number 4-8

Relay output 1

Relay output 2

Relay output 3

SMS message

No report

Triggered “Close” by alarm

No control (not available)

SMS Alarm Message Setup

Alarm channel 1 ~ 8

Command: PWD:XXXX,ALMYTEXT:□□□□□□□□□□□□#%

XXXX

Password

Alarm channel number (1 ~ 8)

0 Close triggered alarm

1 Open triggered alarm

□□□□□□□□

SMS message (max. 130 characters –no space allowed)

Example:

PWD:1234,ALM4T1XT:Door Contact1 Open#%

Password

1234

Alarm channel 4 is triggered by “Open Contact”, SMS message “Door

Contact 1 Open” is sent to the pre-defined phone numbers.

CU2200 v3-03

SMS Message Contents

Command 8 is used to program the alarm message contents. The CU2200 will reply to the mobile

phone with the programmed message for that alarm channel.

Command: PWD:XXXX,READYTEXT%

XXXX

Password

Alarm channel number (1 ~ 8)

Commanding the CU2200 to Send SMS Message

This command is used to make the CU2200 to send the SMS message for testing purposes.

Command: PWD:XXXX,SENDMSA:XB%

XXXX

Password

Phone number (1 ~ 8)

SMS message selection

00: schedule health check status

01:closed triggered alarm channel 1, SMS message

02: closed triggered alarm channel 2, SMS message

03: closed triggered alarm channel 3, SMS message

04: closed triggered alarm channel 4, SMS message

05: closed triggered alarm channel 5, SMS message

06: closed triggered alarm channel 6, SMS message

07: closed triggered alarm channel 7, SMS message

08: closed triggered alarm channel 8, SMS message

09:manual input message

10:Low voltage alarm message

11:AD channel 1, SMS message

12:AD channel 2, SMS message

13:Open triggered alarm channel 1, SMS message

14: Open triggered alarm channel 2, SMS message

15: Open triggered alarm channel 3, SMS message

16: Open triggered alarm channel 4, SMS message

17: Open triggered alarm channel 5, SMS message

18: Open triggered alarm channel 6, SMS message

19: Open triggered alarm channel 7, SMS message

20: Open triggered alarm channel 8, SMS message

Example:

PWD:1234,SENDMS4:09,Good Morning%

Password

1234

SMS message “Good Morning” will be sent to phone number 4.

Error message about setting A:

Number Choice Miss A is not within 1 ~ 8

Number Non Exist No phone number is preset in that location

Error message about setting XB

Did not specify SMS contents XB is not within 00 ~20

Reply confirmation message:

Success!: CU2200 succeeds in sending message.

Failed!: Operation failed but phone number exists.

Relay Output Control

Command: PWD:XXXX,COUTN:Y%

Password

1234

Relay output channel (1 ~ 3) (outputs 2 and 3 not available)

Turn on (close) the output

Turn off (open) the output

The relay output is N.O. by default.

Command COUTN:1 is not valid when the relay output is triggered by alarm. Reply message will be

ST:XXX in this case.

In the above case, command COUTN:0 is used to reset the relay output after the alarm is triggered.

Relay Output Delay Time

Command: PWD:XXXX,OUTNDLAY:YYYY%

XXXX

Password

Relay output channel (1 ~ 3) (outputs 2 and 3 not available)

YYYY

0000 –9999 seconds

0000 Turn the output on or off (default)

0005 Turn on the output for 5 seconds and off again

Turn off the output for 5 seconds and on again

The relay output delay time is good for controlling e.g. an electric door lock.

CU2200 v3-03

Operating Voltage Low Level Alarm Message

When the power supply voltage level is below the minimum level at 5.34VDC, the CU2200 will send

an alarm SMS message.

Date

2007-06-15

Time

13:25

ST:001;TM200706121325;V:5.34#

Operating Voltage Low Level Alarm

This command is used to set the action to be taken once the operating voltage drops below 7.0VDC.

Value of the current operating voltage can be retrieved by command 2.

Command: PWD:XXXX,ADCOUT0:YY,ZZZZBBBB,NNN%

XXXX

Password

00 means alarm not reported to control centre

10 means alarm reported to control centre 1

01 means alarm reported to control centre 2

11 means alarm reported to control centre 1 and 2

ZZZZBBBB

Selection of the alarm phone dial and alarm SMS

0 means no alarm report

1 means SMS only

2 means phone dial only => (Phone dial not available)

3 means SMS first, then phone dial =>(Phone dial not available)

1st

2nd

3rd

4th phone number

5th

6th

7th

8th phone number

NNN

Relay output control

0 means no relay output control

1 means relay output triggered by alarm

1st

2nd

3rd relay output

(2nd and 3rd relay output not available)

Arm/Disarm Setup

Command: PWD:XXXX,ARM%

XXXX

Password

Example:

PWD:1234,ARM%

Password

1234

Unit is armed and in alert status

Command: PWD:XXXX,DISARM%

XXXX

Password

Example:

PWD:1234,DISARM%

Password

1234

Unit is disarmed and no alarm is reported

c. System Information Report

Default Setting

Command: PWD:1234,PARAMETER1%

ST:000;T:2006/10/01/01:01;H:1;F1:,00;F2;,00;XH:31#

Command: PWD:1234,PARAMETER2%

ST:000;VL:7.00,O:00,0000,000;A1M:5.000,0.000,1.000,0,5.000,0.500,O:00,00000000,000;A2M:

5.000,0.000,1.000,0,5.000,0.000,O:00,00000000,000#

Command: PWD:1234,PARAMETER3%

ST:000;K1:1,O:00,00000000,000;K2:1,O:00,00000000,000;K3:1,O:00,00000000,000;K4:1,O:00,

00000000,000;K5:1,O:00,00000000,000;K6:1,O:00,00000000,000;K7:1,O:00,00000000,000;K8:

1,O:00,00000000,000#

Command: PWD:1234,PARAMETER4%

ST:000;C1:,1;C2:,1;C3:,1;C4:,1;C5:,1;C6:,1;C7:,1;C8:,1;#

System Parameters RESET

Command: PWD:XXXX,PARAMETER&%

[SMS message received]

Parameter initialize success!

Otros manuales para CU2200

Tabla de contenidos

Idiomas:

Otros manuales de PDA de Velleman

Velleman

Velleman HAMGSM Manual de usuario

Manuales populares de PDA de otras marcas

SPOT

SPOT SPOT Manual de usuario

Palm

Palm handheld Manual de usuario

Winmate

Winmate E500QK Manual de usuario

Getac

Getac PS236 Manual de usuario

Sharp

Sharp CE-1600P Manual de usuario

HTC

HTC PHAR100 Manual de usuario

Mindeo

Mindeo M40 Manual de usuario

Acer

Acer n30 Manual de usuario

ASCOM

ASCOM 9D24 EX Manual de usuario

Unitech

Unitech PA520BTNF Manual de usuario

HandHeld

HandHeld Nautiz X3 Manual de usuario

Casio

Casio PALM Manual de usuario

Sharp

Sharp TM-20 Guía de inicio rápido

Atid

Atid AT870 Manual de usuario

AML

AML M7225 Manual de usuario

Audiovox

Audiovox Maestro Manual técnico

Casio

Casio PV-750 Plus Manual de instrucciones y seguridad

Unitech

Unitech PT630 Manual de usuario