Velkase VELKA 5 Manual de usuario
Velkase Velka 5 rev 2.0 user manual (short version)
Download the detailed and most up-to-date version of the user manual at https://www.velkase.com/downloads
Specification Hardware compatibility
Dimensions
177 x 99 x 285 mm
Weight
2.0 kg
Materials and finish
5 mm aluminum front panel
1.2 mm galvanized steel and stainless
steel body
1.0 mm galvanized steel side panels
I/O
Rear: Motherboard, graphics
Discrete graphics: uses internal
extensions. 2x DisplayPort 1.2, 1x HDMI
2.0. DVI is not supported.
Security
Kensington Lock Slot
PCIe riser
PCIe 3.0 x16
Test all of your components before assembling a system in the case.
1. Assemble the computer with the graphics card plugged directly into the motherboard, test for functionality
2. In BIOS, set PCIe speed / compatibility mode to gen 3, test for functionality
3. Repeat step (1) with the PCIe riser, DisplayPort and HDMI extensions. Be gentle with these cables as they are not designed for
external use.
Disassembly
1. 2 screws on top-front and 2 screws on bottom-front to remove front panel
2. 6 screws in the front and 5 screws in the back to remove side panels
3. 2 screws on the left and 2 screws on the right to remove struts
4. 2 screws in the rear and 2 screws on bottom to remove motherboard tray, 2 screws in the rear to remove 2.5” drive bracket
Assembly
Motherboard
Mini ITX
170 x 170 mm
Power supply
Flex ATX (150 mm)
CPU cooler
37 mm
Graphics card
(L x W x H)
Maximum clearance, including
cables. Cables require 16 mm if not
recessed into the board.
270 x 43 x 140* mm
*If card is 243 mm in length or under,
max card height is 140 mm and max
card + cable height is 145 mm
Memory
42 mm
Storage
1x 2.5” HDD or SSD (7.0 mm thick)
If graphics card length is <193 mm:
3x extra 2.5” drives (2x up to 12.5
mm thick, 1x up to 7.0 mm thick)
-Slot graphics card into riser
-Attach the card. It must not have
protrusions past the bracket edge
-Install CPU, cooler, memory, and
M.2 drive onto the motherboard
-Attach motherboard to the tray and
plug in the PCIe riser
-Bend female end of riser to form a 180 degree turn
-Bend the middle section at an angle two times to put
the female end in place and secure with screws. Leave 5
mm between the middle bends to prevent “stacking”
-Avoid making repeat bends as this will stress the wires
-Plug video cables into graphics card. Fold them
so that they do not protrude past the bracket edge
-Avoid making creases near the connector to
reduce risk of damage
-Insert PSU. Vents should
face outwards
-4x 6-32 screws
-Insert the motherboard subassembly into the case
-3x countersunk 5 mm M3 screws (GPU bracket)
-2x round head 4 mm M3 screws (motherboard
tray)
-6x round head 6 mm M4 screws
-Install the storage drive / PSU holder
-Attach storage drive
-Connect cables to all components
-1x round head 4 mm M3 screws (drive /
PSU holder)
-4x countersunk 5 mm M3 screws
(storage drive)
-All cables must be plugged in
before this step
-Complete the frame by installing
the two struts in the front
-4x countersunk 5 mm M3 screws
-Temporarily remove bottom bracket to install
button
-Use the hex nut to fix the button in place, then
reinstall the bottom bracket
-Consult your motherboard manual for the front
panel header pin layout. Plug the power button wires
into the corresponding motherboard pins
-Power button must be plugged in
-Side panels have 3 positions. Flush mount: outer-
most positions for top and bottom screws and the
middle position for the middle screw
-For quieter operation, use other mounting holes
-6x countersunk 5 mm M3 screws (front)
-6x round head 4 mm M3 screws (rear)
-Slide in front panel while inserting the button’s
cable into the case. Screw in on top and bottom
-Reposition the brackets behind the front panel for
a more loose fit
-Stick on the included adhesive rubber pads
-4x countersunk 5 mm M3 screws
Otros manuales para VELKA 5
1
Otros manuales de Accesorios de computadora de Velkase
