Varytec Gigabar III Manual de usuario

User manual

Gigabar III

2 / 10

Table of contents

1.Safety instructions............................................................................................................................ 3

1.1.FOR SAFE AND EFFICIENT OPERATION............................................................................ 3

2.Technical Information....................................................................................................................... 4

3.DMX Mode ....................................................................................................................................... 4

3.1.DMX chart................................................................................................................................ 4

4.Control of the Menu.......................................................................................................................... 6

4.1.Menu structure......................................................................................................................... 6

4.2.Description of the Menu........................................................................................................... 7

5.Master Slave configuration............................................................................................................... 8

6.Sound to Light.................................................................................................................................. 8

7.Technical Data ................................................................................................................................. 9

3 / 10

1. Safety instructions

•This device is suitable for indoor use only.

•All modifications to the device will void the warranty.

•Repairs are to carry out by skilled personnel only.

•Use only fuses of the same type and original parts as spare parts.

•Protect the unit from rain and humidity to avoid fire and electric shocks.

•Make sure to unplug the power supply before opening the housing.

1.1.FOR SAFE AND EFFICIENT OPERATION

Be careful with heat and extreme temperature

Avoid exposing it to direct rays of the sun or near a heating appliance.

Not put it in a temperature bellow 32°F /0°C, or exceeding 104°F /40°C.

Keep away from humidity, water and dust

Do not place the set in a location with high humidity or lots of dust.

Containers with water should not be placed on the set.

Keep away from sources of hum and noise

Such as transformer motor, tuner, TV set and amplifier.

To avoid placing on un-stable location

Select a level and stable location to avoid vibration.

Do not use chemicals or volatile liquids for cleaning

Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt.

If out of work, contact sales agency immediately

Any troubles arose, remove the power plug soon, and contact with an engineer for repairing,

do not open the cabinet by yourself, it might result a danger of electric shock.

Take care with the power cable

Never pull the power cable to remove the plug from the receptacle, be sure

to hold the plug. When not using the device for an extended period of time, be sure to

disconnect the plug from the receptacle.

4 / 10

Important: Damages caused by the disregard of this user manual are not subject to

warranty. The dealer will not accept liability for any resulting defects or

problems. Make sure the electrical connection is carried out by qualified

personnel. All electrical and mechanical connections have to be carried out

according to the European safety standards.

2. Technical Information

- RGB 3in1 LEDs

- DMX Mode (3, 5, 8, 14, 24 or 26Ch)

- Sound to light mode via internal mic

- 12 Programs internal

- Digital display for addressing and functions

- Power and DMX can be daisy chained

3. DMX Mode

To use the DMX Mode you have to adjust the address first, as described a few articles below. The

item needs 3, 5, 8, 14, 24 or 26 channels, which you can adjust by using your faders of your DMX

console. You can adjust as follows:

3.1.DMX chart

Function 3 Ch Mode 5 Ch Mode 8 Ch Mode 14 Ch

Mode

24 Ch

Mode

26 Ch

Mode

Dimmer &

internal

Programs

1 1 1 1

Speed 2 2 2 2

Red 1 3 3 3 1 3

Green 2 4 4 4 2 4

Blue 3 5 5 5 3 5

Red 6 6 4 6

Green 7 7 5 7

Blue 8 8 6 8

Red 9 7 9

Green 10 8 10

Blue 11 9 11

Red 12 10 12

Green 13 11 13

Blue 14 12 14

Red 13 15

5 / 10

Green 14 16

Blue 15 17

Red 16 18

Green 17 19

Blue 18 20

Red 19 21

Green 20 22

Blue 21 23

Red 22 24

Green 23 25

Blue 24 26

Functions for the Dimmer and internal Programs channel:

Value Function

0 – 7 Dimmer

8 – 15 Strobe

16 – 23 Program 1

24 – 31 Program 2

… …

224 – 231 Program 27

232 – 239 Sound Active Program 1

240 – 247 Sound Active Program 2

248 – 255 Sound Active Program 3

Function for Speed channel:

0 – 255 Slow to fast

If you use cables longer then 100m you should put in a terminator at the last item in your daisy chain!

Use DMX cables with a 120Ohms shield only! All Plugs should use XLR connectors!

The connectors configuration is as follows:

6 / 10

If you want to produce a DMX terminator on your own, you have to insert a Terminator at the plug.

This should have a size of 120Ohms and 1/4W. It has to be inserted between Pin 2 (Data -) and Pin 3

(Data +).

4. Control of the Menu

4.1.Menu structure

Addr

001

512

Auto

Aut 1

CHND

3 CH

5 CH

Aut 2

Aut 3

SP 1

SP 2

8 CH

14CH

24CH

26CH

CoLo

CoL1

Col 9

ver

AtF

000

255

bLUe

b000

b255

G000

G255

SoU

SoU2

SoU3

7 / 10

4.2.Description of the Menu

Addr DMX address setting

1. Push the UP/DOWN buttons until the display shows Addr.

2. Push ENTER

3. 1 appears in the display blinking. With the UP/DOWN buttons you can no adjust the DMX

address from 1 to 512

4. Push ENTER to confirm

AUto Automatik Shows

1. Push the UP/DOWN buttons until the display shows AUto.

2. Push ENTER

3. Use the UP/DOWN buttons to choose from AUt1, AUt2 or AUt3.

4. Push ENTER to get into the speed menu. The display shows SP

5. Push again ENTER to see SPx in the display.

6. Here you can choose with the UP/DOWN Buttons from SP1 to SP99 to adjust the speed.

CHNd channel adjust

1. Push the UP/DOWN buttons until the display shows CHNd.

2. Push ENTER

3. Use the UP/DOWN buttons to choose from CH3, CH5, CH8, CH14, CH24 or CH26.

4. Push ENTER to confirm

CoLo Choose your color

1. Push the UP/DOWN buttons until the display shows CoLo.

2. Push ENTER

3. Use the UP/DOWN buttons to choose from colors 1 - 9

4. Push ENTER to confirm

5. If you want you can choose AtF in this submenu by using ENTER.

6. Now you can choose from Red, green and blue. Confirm with ENTER.

7. For each color you can adjust the brightness from 000 to 255.

Soun Sound To Light Mode

1. Push the UP/DOWN buttons until the display shows Soun.

2. Push ENTER

3. Use the UP/DOWN buttons to choose from SoUn1, SoUn2 or SoUn3.

4. Push ENTER to confirm

8 / 10

SLav Master Slave Mode

1. Push the UP/DOWN buttons until the display shows SLav.

2. Push ENTER

3. Now the display shows now Sla, this confirms the salve mode.

4. The slave mode reacts to Automatic programs, sound to light mode odr chaser mode of the

master item. To do so the master doesn’t has to be set up special. For a master slave

configuration, just connect all the desired items by dmx cables.

Ver Software Version auslesen

1. Push the UP/DOWN buttons until the display shows SLNd.

2. Push ENTER

3. Now the display shows the actual software version

5. Master Slave configuration

If you want to daisy chain and control more than one item you can use the Master Slave Mode. To do

so you have to daisy chain your items as you would do when you want to set up a dmx chain. You can

use max 16 items for this mode. The first item in line is the master and the other items will react

according to him. The master item can be set up to the desired program or mode and the others will

follow. The slave items should be set up as follows.

1. Push the Menu button as often until you see SLav in the display. Push Enter to confirm.

2. No choose the desired Slave mode is confirmed.

3. The slave item will now react according to the master.

6. Sound to Light

- Set up the sound to light mode to ON as described above.

- Now the item will react according to the sensitivity of the mic.

- This option can be used with the master slave mode as well.

9 / 10

7. Technical Data

Voltage: 100V ~ 240V 50/60Hz

Power consumption: 80W max.

Fuse: 3A

Lightsource: 16 x 3W 3in1 LEDs

Beam angle: 40°

Weight: 5,3kg

Measures: 965 x 64 x 153 mm

Modes: DMX (3, 5, 8, 14, 24 oder 26 Ch)

Automatic Mode

Sound To Light Mode

Master Slave Mode

10 / 10

Importer:

B & K Braun GmbH

Industriestraße 1

D-76307 Karlsbad

www.bkbraun.com

[email protected]

Tabla de contenidos

Otros manuales de Equipo de DJ de Varytec

Varytec

Varytec LED Pad 7 7x10W 6in1 RGBWAUV Manual de usuario

Varytec

Varytec BAT.BAR 240 RGB Manual de usuario

Varytec

Varytec 92043 Manual de usuario

Varytec

Varytec LED Magicball Manual de usuario

Varytec

Varytec Hero Spot 60 WH Manual de usuario

Varytec

Varytec LED Accu Street Bar Manual de usuario

Varytec

Varytec LED Derby ST Manual de usuario

Varytec

Varytec Spot 90 Manual de usuario

Varytec

Varytec QUAD VISOR FX Manual de usuario

Varytec

Varytec Giga Bar HEX 3 Manual de usuario

Varytec

Varytec Hero Spot Wash 140 2in1 RGBW+W Manual de usuario

Varytec

Varytec Easymove XL 60 Spot Manual de usuario

Varytec

Varytec LPS 20 Manual de usuario

Varytec

Varytec COMPLEX Manual de usuario

Varytec

Varytec Street Bar MK3 Manual de usuario

Varytec

Varytec LED Accu Pad 7 Manual de usuario

Varytec

Varytec Easy Move XS HP Wash Manual de usuario

Varytec

Varytec ARC One Manual de usuario

Varytec

Varytec LA VIDA Manual de usuario

Varytec

Varytec 103340 Manual de usuario

Varytec

Varytec LED Street Bar 16x3W RGB IP65 Manual de usuario

Varytec

Varytec LED RealBeam 7 RGBW Manual de usuario

Varytec

Varytec Typhoon True Kid 720Z RGBW Manual de usuario

Varytec

Varytec LED Pad 144 144x10mm RGBW Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario