Vanguard PORTABOOM 49-PB Guía de inicio rápido
This SOP does not necessarily cover all possible hazards associated with the plant and should be used in conjunction with
other references –This SOP remains the property of Traffic and Access Solutions Pty Ltd –PORTABOOM® brand and designs
are registered trademarks of Traffic & Access Solutions Pty Ltd ABN 162 894 975
Safety glasses must be worn at all
times in work areas.
Gloves must be worn at all times when
handling equipment.
Steel cap boots must be worn at all
times in work areas.
Hard hat must be worn at all times
while working.
PRE-OPERATIONAL SAFETY CHECKS
1. Ensure that the PORTABOOM® PRE-START inspection checklist is completed prior to utilisation,
PORTABOOM® must be in a safe and working condition prior touse.
2. Faulty equipment must not be used. Immediately report suspect equipment toyour Supervisor.
PORTABOOM® SITE OPERATIONAL INSTRUCTIONS
One operator operating one PORTABOOM®:
1. Park vehicle / trailer used to transport PORTABOOM® at setup location on as close to level
ground as possible.
2. Unload PORTABOOM® Tower using safe manual handling techniques including straight
back and bending at the knees.
3. Must be inside an existing TTM worksite.
4. Must be positioned so they are clear of any moving or operating plant and/or machinery.
5. Must not undertake any other task or work activity whilst in control of the PORTABOOM
units.
6. It is recommended that the PORTABOOM® operator is not further than 75mtrs from the
PORTABOOM® Tower.
7. Must have a visual of 120m on the approach to the PORTABOOM® Tower you are
operating.
8. Must be ready and in position to invoke manual or STOP/SLOW operation if required.
PORTABOOM® must not be operated unless it is in a safe condition for use.
DO NOT use this unless you have reviewed & understand this procedure.
This SOP does not necessarily cover all possible hazards associated with the plant and should be used in conjunction with
other references –This SOP remains the property of Traffic and Access Solutions Pty Ltd –PORTABOOM® brand and designs
are registered trademarks of Traffic & Access Solutions Pty Ltd ABN 162 894 975
One operator operating multiple PORTABOOM®S:
1. Must be inside an existing TTM worksite.
2. Must be positioned so they are clear of any moving or operating plant and/or machinery.
3. Must not undertake any other task or work activity whilst in control of the PORTABOOM
units.
4. Must have a visual of 120m on the approach to each PORTABOOM® Towers you are
operating.
5. Must be within 75mtrs of all PORTABOOM® Towers.
6. Must label PORTABOOM® Towers with magnets provided.
7. Must utilize remote control caddy at all times ensuring the remote controls are labelled
same as the PORTABOOM® Tower magnets.
8. Always remain in a central position when operating PORTABOOM® Towers.
9. If a PORTABOOM® Tower fails you must:-
a) be prepared to manually operate the failed Tower and operate the “other” Tower by
using the remote control.
OR
b) be prepared to perform STOP/SLOW in place of the failed Tower and operate the
“other” Tower by using the remote control.
This SOP does not necessarily cover all possible hazards associated with the plant and should be used in conjunction with
other references –This SOP remains the property of Traffic and Access Solutions Pty Ltd –PORTABOOM® brand and designs
are registered trademarks of Traffic & Access Solutions Pty Ltd ABN 162 894 975
GENERAL
•Ensure all persons, hands and limbs are clear from crush / drop zones at all times.
•Ensure equipment is loaded and unloaded as specified in this procedure and all items are secure
prior to driving.
HOUSE-KEEPING
•Switch off equipment.
•Leave the equipment and work area in a safe, clean and tidy state.
•Ensure NO equipment is left on the ground where it can be damaged.
POTENTIAL HAZARDS
•Falling objects.
•Trapping hazards.
•Crushing hazards.
•Entanglement hazards.
•MH hazards.
•People.
•Damaged plant.
This SOP does not necessarily cover all possible hazards associated with the plant and should be used in conjunction with
other references –This SOP remains the property of Traffic and Access Solutions Pty Ltd –PORTABOOM® brand and designs
are registered trademarks of Traffic & Access Solutions Pty Ltd ABN 162 894 975
PORTABOOM® SET UP
Step
Instruction
Diagram
1.
Once arriving to site, review Traffic
Management Diagram (TMD) and identify
required positions of PORTABOOM® unit(s)
on site.
“MANUAL TRAFFIC CONTROL”TA2/TA21 sign
is to be placed in accordance with dimension
“C” sign spacing.
Diagram F2.14a is based on diagram F2.14
TWO-WAY TWO-LANE ROAD, single lane
alternating flow which has been modified to
incorporate the PORTABOOM® unit.
Note: PORTABOOM® Operators are to
remain at least 2m away from the live lane
an d in a safe location.
This SOP does not necessarily cover all possible hazards associated with the plant and should be used in conjunction with
other references –This SOP remains the property of Traffic and Access Solutions Pty Ltd –PORTABOOM® brand and designs
are registered trademarks of Traffic & Access Solutions Pty Ltd ABN 162 894 975
2.
Prior to commencement of PORTABOOM®
setup, an assessment of overhead hazards
must be conducted.
3.
If overhead hazards have been identified
where a PORTABOOM® needs to be
positioned, the Site Traffic Management
Supervisor (STMS) in consultation with the
PORTABOOM® Operator may be able to
reposition the PORTABOOM® in order to
remove the overhead hazard.
If a new position has been identified, ensure
that the scope of works can be maintained,
the change of location is recorded on the
On-site Record and the TMD is amended to
show the new location of the
PORTABOOM®.
This SOP does not necessarily cover all possible hazards associated with the plant and should be used in conjunction with
other references –This SOP remains the property of Traffic and Access Solutions Pty Ltd –PORTABOOM® brand and designs
are registered trademarks of Traffic & Access Solutions Pty Ltd ABN 162 894 975
4.
Prior to setup, assess weather conditions
by checking an approved or trusted
weather radar for current and forecasted
weather conditions.
If the current or forecasted weather advises
of strong winds exceeding 50kph (kilometers
per hour) then add weight to the Stability
Legs using sandbags when setting up
PORTABOOM®s as per steps 34, 35, 36 and
37.
Note 1: It is mandatory to remain diligent and
vigilant with regards to environmental
changes on the work site at all times –
Environmental changes could result in having
to add weight to the PORTABOOM® legs to
ensure safety and stability.
Note 2: It is also mandatory to routinely (at
least every 2 hours) check the forecasted
weather conditions and take a proactive
approach to securing the PORTABOOM®’/s
with additional weight if and when
necessary.
This SOP does not necessarily cover all possible hazards associated with the plant and should be used in conjunction with
other references –This SOP remains the property of Traffic and Access Solutions Pty Ltd –PORTABOOM® brand and designs
are registered trademarks of Traffic & Access Solutions Pty Ltd ABN 162 894 975
5.
PORTABOOM® Tower Setup Process
As per steps 2 and 3, identify potential
hazards prior to positioning PORTABOOM®
i.e. Look for low lying power lines, tree
branches, street lights, road signage which
the PORTABOOM® Boom Arm may come in
contact with in its setup and operation.
(PORTABOOM® Boom Arm raised)
Ensure PORTABOOM® is setup with
PORTABOOM® Boom Arm raised after
identifying a position clear of all hazards
Also noting that when on site there may be a
requirement due to loose surface conditions,
uneven surfaces and/or restricted spaces to
move the PORTABOOM® Tower to a location
that would be more suitable for operation (i.e.
a position that would be more level).
Ensure any changes are updated on the On-
site Record and TMD.
This SOP does not necessarily cover all possible hazards associated with the plant and should be used in conjunction with
other references –This SOP remains the property of Traffic and Access Solutions Pty Ltd –PORTABOOM® brand and designs
are registered trademarks of Traffic & Access Solutions Pty Ltd ABN 162 894 975
6.
Prior to installation make sure there are
appropriate TTM controls in place for the
protection of the installer(s).
Position PORTABOOM® Tower in the
shoulder/kerb for set up. Ensuring the shaft
is facing the footpath
7.
Once in position enable PORTABOOM®
Tower brakes by pushing down on brake
pedals at the bottom of the PORTABOOM®
Towers.
This SOP does not necessarily cover all possible hazards associated with the plant and should be used in conjunction with
other references –This SOP remains the property of Traffic and Access Solutions Pty Ltd –PORTABOOM® brand and designs
are registered trademarks of Traffic & Access Solutions Pty Ltd ABN 162 894 975
8.
Remove Boom Arm from carry bag.
Position the Boom Arm at approx. 45
degrees to the Tower.
This SOP does not necessarily cover all possible hazards associated with the plant and should be used in conjunction with
other references –This SOP remains the property of Traffic and Access Solutions Pty Ltd –PORTABOOM® brand and designs
are registered trademarks of Traffic & Access Solutions Pty Ltd ABN 162 894 975
9.
Align the Boom Arm billet tabs (indicated by
arrows).
With the channels on the shaft (indicated by
arrows).
10.
Position the Boom Arm square onto the
shaft and align the billet tabs with the
channels on the shaft.
Tabla de contenidos
