Van Der Valk ValkBox3 Manual de usuario
Version 01 |May 2023
Installation manual ValkBox3
Installation manual ValkBox3
Components
A
4x 2x 4x
3x
5x (1 spare)5x (1 spare) 9x (1 spare)
B C
Installation manual ValkBox3
Step 1: Mounting the clevis Step 2: Mounting the curved supports
Depending on the panel width, the clamps B1 and B2
must be positioned inwards or outwards. The correct
orientation for each panel width is shown on the next
page.
Tighten the hinge bolts B1 by hand. These must be
removed temporarily at step 4.
Tighten the hinge bolts B2 rmly, with a tightening
torque of at least 9 Nm, until there is no more play.
The curved aluminum supports are suitable for
panels with a width of 926 - 1150 mm.
A
A
A
A
B1
B1
B2
B2
Tightening torque
at least 9 Nm.
Installation manual ValkBox3
Option 1: Mounting panel
Option 2: Mounting panel
Option 3: Mounting panel
For panel width 926 - 990 mm
Center to center mounting holes (panel frame): 896 - 970 mm
For panel width 991 - 1070 mm
Center to center mounting holes (panel frame): 970 - 1050 mm
For panel width 1071 - 1150 mm
Center to center mounting holes (panel frame): 1050 - 1124 mm
Under lip
turned inwards
Under lip
turned inwards
Under lip facing
outwards
Top lip facing
inwards
Top lip facing
out
Top lip facing
out
C (1 : 4)
F (1 : 4)
A (1 : 4)
C
F
A
D (1 : 4)
E (1 : 4)
B (1 : 4)
D
E
B
Step 3: Placing the rubber tiles Step 4: Position the ballast
Turn over the panel and place it on the rubber tile carriers. Remove the top hinge bolts B1 and place the panel in a vertical position. Make
sure that you have some form of support in place or someone to hold the panel
temporarily.
The projections on the curved aluminium
supports must be placed in the grooves on
the rubber tiles.
Position the ballast required.
Installation manual ValkBox3
C
CC
C
Step 5: Tighten hinge bolts B1 Step 6: Finish tting the cables
Step 7: Position the rows one behind each other
Attach the panel to the curved supports again and tighten hinge bolts B1. The loose cables can be secured to the edge of the panel. Using the
cable clamps supplied.
If a number of rows of panels are to be positioned one behind the other, we advise
that an optimal pitch measure of 2.20 metres is observed; this will avoid any
unwanted shadow. Optimal performance will be achieved if this pitch measure is
used. Based on sun angle of 15 degrees.
B1
B1 D
Tighten hinge bolts B1 tightly, with a
tightening torque of at least 9 Nm, until
there is no more play.
pitch measure
Installation manual ValkBox3
Otros manuales para ValkBox3
2
Tabla de contenidos
Otros manuales de Panel solar de Van Der Valk
Van Der Valk
Van Der Valk ValkTriple Manual de usuario
Van Der Valk
Van Der Valk ValkDouble Manual de usuario
Van Der Valk
Van Der Valk ValkQuattro Manual de usuario
Van Der Valk
Van Der Valk ValkBox3 Manual de usuario
Van Der Valk
Van Der Valk ValkDouble Manual de usuario
Van Der Valk
Van Der Valk ValkPro+ L10 East-West Manual de usuario
Van Der Valk
Van Der Valk ValkField Manual de usuario
Van Der Valk
Van Der Valk ValkBox3 Manual de usuario
