Valcom V-D11025B Manual de usuario
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
USA
P. 540-563-2000
F. 540-362-9800
www.valcom.com
Installation Manual V10.5
Valcom Wired Digital Clock
Current as of February 2017
V-D11025B, V-D11040B, V-2425B-6, and V-D2440B-6
2
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
USA
P. 540-563-2000
F. 540-362-9800
www.valcom.com
Manuals may change without prior notice
Valcom Digital Series 2-Wire and 3-Wire Clocks
Table of Contents
Table of Contents 2
Important Safety Instructions 3
Wall Mount Installation 4 - 10
Flag Mount Installation 11 - 19
Double Mount Installation 20 - 28
Adjustable Jumper Settings 29
Inputs
System Side - 2-Wire Digital Communication 30
- 3-Wire Synchronous (Sync-Wire)
Communication 110VAC 31
Clock Side - Sync-Wire 32-35
Outputs 36
Manual Controls 37-43
Reading the Display 44
Frequently Asked Questions 45
Troubleshooting 46
Warranty 47
Available with V-D110XXB models only
Important Safety Instructions
,H
! !
3
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
USA
P. 540-563-2000
F. 540-362-9800
www.valcom.com
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
USA
P. 540-563-2000
F. 540-362-9800
www.valcom.com
|
NOTICE
• Do not install the clock outdoors.
Damage to the clock if placed outdoors
voids the warranty.
• Do not hang objects from the clock or clock
mounting parts. The clocks are not designed
to support the weight of other objects.
• The clock face and housing may be cleaned
with a damp cloth or disinfectant. Test
other cleaning products on a small part of
the clock housing before attempting to use
on the rest of the clock. Avoid bleach and
chemicals known to dissolve plastics.
VERY IMPORTANT:
KNOW YOUR COMMUNICATION PROTOCOL
The Valcom V-D110XXB Digital clocks are designed to support various 3-wire (sync-wire) communication
protocols. To run each protocol properly, the clock requires the correct wiring format. It is very important
that you only follow the wiring instructions appropriate to your clock’s communication protocol. Using the
wrong wiring format may damage the clock.
WARNING
FIRE HAZARD
• Always follow your national and regional
electrical codes or ordinances.
• The AC power circuit for the clock must
be attached to a circuit breaker that can
be reset by the user.
PHYSICAL INJURY HAZARD
• If you are standing on an object while
installing your clock, make sure that the
object can support your weight, and will not
sway or move as you stand on it.
• Take precautions to avoid injury by potential
safety hazards near the point of installation
including (but not limited to) heavy
machinery, sharp objects, hot surfaces, or
exposed cables carrying an electric current.
• Follow all mounting instructions exactly as
stated in this manual. Failure to do so may
result in the device falling off the point of
installation.
• Packaging materials and mounting items
include plastic bags and small pieces, which
pose a suffocation hazard to young children.
DANGER
SHOCK HAZARD
• Keep the electricity to this device turned
OFF until the clock installation
is complete.
• Do not expose the clock movement to
water, or install the clock in a location
where it may be exposed to water.
4
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
USA
P. 540-563-2000
F. 540-362-9800
www.valcom.com
Wall Mount Installation
Included in Package
Description
Valcom Digital Clock
Digital Clock Wall Housing
6-19x1/2 screw
6-32x1 screw
Quantity
1
1
4
4
Picture
PLEASE NOTE: A user will also have to provide a Phillips-head screwdriver, a small flat-blade screwdriver, a single gang box, any equipment needed to install
the gang box, and any additional wiring needed to extend the signal, power, or ground cables. You may also need a 1/4 inch drill, 4 #8x1.5 self-tapping
screws, and 4 wall anchors for those screws if you decide not to attach the clock directly to the gang box.
If any of the items listed in the wiring kit are missing, you may contact Valcom and order a
replacement kit.
Included in Wiring Kit (D-PK-3-110-S or D-PK-3-24-S)
Power/grounding wires
and connector
1or
110V 24V
12
3 4
5
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
USA
P. 540-563-2000
F. 540-362-9800
www.valcom.com
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
USA
P. 540-563-2000
F. 540-362-9800
www.valcom.com
3) Attach the communication and power wires from
your kit to the communication and power wires
in the gang box. See the sections of this manual
labeled “Communication Wiring Information”for
additional details, depending on your system.
Wall Mount Installation
1) If you are installing a new gang box in the wall,
leave at least 4 inches between the top of the gang
box and ceiling. Confirm that the bottom of the
gang box is level with the floor.
If you are using an existing gang box, the top of the
gang box must be a minimum of three inches away
from the ceiling.
4) If you do not wish to attach the housing to the
gang box, proceed to step 5A. Otherwise, go to
step 6.
Ceiling
4” Minimum
2) Run power and communication wiring to the
gang box. See the sections of this manual labeled
“Inputs - System Side” for additional details,
depending on your system.
CHECK YOUR WIRING
The voltage between the white and black wires
should measure 105-126 volts AC in the 110
volt model, or Yellow & orange wires for 21.5-
26.5 volts DC in the 24 volt model.
If you are using the 24 volt model, make sure
that the wiring leading to the clock is from a
Valcom power supply or V-VCU.
5C
5A
5D
5B
6
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
USA
P. 540-563-2000
F. 540-362-9800
www.valcom.com
Wall Mount Installation
5D) Use the keyholes in the back of the housing to
hang the clock onto the screws.
5A) If you do not wish to attach the housing to a
gang box, place the mounting piece on the wall.
Leave at least 4 inches between the top rear edge
of the housing and ceiling. Confirm that the bottom
of the mounting piece is level with the floor.
5B) Identify the keyholes towards the top of the
back of the clock housing. Use a pencil to trace the
top of each keyhole onto the wall, then use the
1/4 inch drill bit to drill holes at the locations of the
two marks.
5C) Insert the wall anchors into the two holes, then
place a #8 self-tapping screw into each wall anchor,
leaving at least a 1/8” gap between the top of the
screw and the wall.
Ceiling
4” Minimum
5G
5E
6
5F
7
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
USA
P. 540-563-2000
F. 540-362-9800
www.valcom.com
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
USA
P. 540-563-2000
F. 540-362-9800
www.valcom.com
Wall Mount Installation
6) Perform step 5F, then attach the housing to the
gang box using the #6-32x1 screws.
5E) Use a pencil to trace the holes beneath each
keyhole onto the wall. Take the clock housing off
the wall, drill holes at the marked locations, and add
another two wall anchors.
5G) Run power and signal wires through the large
hole in the back of the housing. Secure the wires by
passing them through the wire clamp.
5F) Repeat step 5D, then pass another pair of #8
screws through the bottom holes and secure them
in the remaining two wall anchors.
7 8A
8B
8
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
USA
P. 540-563-2000
F. 540-362-9800
www.valcom.com
Wall Mount Installation
7) Detach the filter from the clock display board by
pressing inward on the red tabs.
8B) If you are installing a digital clock that uses sync-wire correction, attach the wires to the appropriate
sync-wire ports. Refer to the section, “Inputs - Clock Side - Sync Wire” for instructions regarding each
system.
8A) If you are installing a digital clock that uses a
2-wire digital sync system, attach the wires to the
port as shown below.
1
2
3
4
5
24VDC (Orange)
24VDC (Yellow)
110VAC (Black)
110VAC (White)
Sync-Wire Ports 1
2
3
4
5
Ground (Green)
11
9
12
10
9
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
USA
P. 540-563-2000
F. 540-362-9800
www.valcom.com
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
USA
P. 540-563-2000
F. 540-362-9800
www.valcom.com
Wall Mount Installation
12) Place the filter over the display board. You
should hear a snapping noise as the latches drop
into place.
9) Detach the frame from the front of the clock
housing by pulling the bottom and top edges away
from the housing.
10) Use the 6-19x1/2 screws to attach the display
board to the housing.
NOTE: For 2.5” Digit clocks, the holes for the
screws will be on the left and right inner surfaces of
the housing. For 4.0” Digit Clocks, the holes will be
on the top and bottom surfaces.
11) Remove the plastic cover from the display board.
13 14
10
Valcom, Inc.
5614 Hollins Road
Roanoke, VA 24019
USA
P. 540-563-2000
F. 540-362-9800
www.valcom.com
Wall Mount Installation
13) Place the housing frame onto the housing. You
should hear a snapping noise as the latches drop
into place.
14) Power the clock. After testing the LED segments
and presenting some diagnostic information, the
clock will display the time based off if its internal
quartz oscillator. It will correct itself to show
synchronized time as soon as it receives data from a
master clock.
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Reloj de Valcom
Valcom
Valcom V-D11025A Instrucciones de montaje
Valcom
Valcom VIP-A12ADS Manual de usuario
Valcom
Valcom V-WMCA Series Manual de usuario
Valcom
Valcom V-A2412 Manual de usuario
Valcom
Valcom VIP-MC Manual de usuario
Valcom
Valcom IP Solutions VIP-A12DS Manual de usuario
Valcom
Valcom VIP-D425ADS Manual de usuario
Valcom
Valcom VIP-429A-A-SA Manual de usuario
Valcom
Valcom 12" Manual de usuario
Valcom
Valcom VIP-429A-A Manual de usuario
Valcom
Valcom VIP-D425A Manual de usuario
Valcom
Valcom V-AW12A Manual de usuario
Valcom
Valcom V-DW11025B Instrucciones de montaje
Valcom
Valcom VIP-A12ADS Manual de usuario
Valcom
Valcom VIP-429A-A-IC Manual de usuario
Valcom
Valcom InformaCast VIP-431-A-IC Manual de usuario
Valcom
Valcom V-A2412 Manual de usuario
Valcom
Valcom VIP-D425 Manual de usuario
Valcom
Valcom VIP-D425DS Manual de usuario
Valcom
Valcom VE4122-A12 Manual de usuario
Manuales populares de Reloj de otras marcas
Silicon Laboratories
Silicon Laboratories SI5324 Manual de usuario
Heathkit
Heathkit GC-1005 Manual de usuario
Oregon Scientific
Oregon Scientific PRYSMA RMR221P Manual de usuario
Andrew O'Malley
Andrew O'Malley DOTKLOK Manual de usuario
ALGE-Timing
ALGE-Timing ASC3 Manual de usuario
Bodet
Bodet Profil 960 Manual de usuario
