VAG-Navisystems NaviTouch Manual

Installation and configuration manual

Compatibility with vehicles that have Concert/Simphony

radio which includes a 6,5" color screen

Index

1. Component identification – Page 3

1.1.Multimedia interface components – Page 3

1.2.GPS Box components– Page 4

1.3.Voice module componenets – Page 4

2. Installation – Page 5

2.1.Disassembling cockpit parts – Page 5

2.2.Performing the NaviTouch® system installation– Page 8

2.3.Connections diagram – Page 10

2.4.Connecting an aftermarket rearview camera – Page 11

2.5.Installing and connecting GPS Box – Page 11

2.6.Installing and connecting the voice module – Page 13

2.7.Linking up the interface GPS Box and the multimedia interface – Page 14

3. GPS Box configuration – System configuration – Page 14

3.1.RESET – Page 15

3.2.Maps SD card and GPS signal – Page 16

3.3.Checking the GPS signal – Page 16

4. FAQ’S/Solving problems – Page 18

Basic knowledge before installation:

•Please, read fully and carefully this installation handbook before you attempt to install the kit in your vehicle.

•Start installation once you have the car stopped and the key out of the ignition slot, supply power must be the

last step in installation.

•When you connect the product and his accessories cables or connections to the vehicle components, the power

cables of the products must be unplugged.

•Make sure that there are no electric or magnetic devices near of the installation place.

•Installation must be performed by a qualified specialist.

•Product loses his warranty if you dismantle it or if you try to fix it without the manufacturer permission. If you

break up product security stickers, warranty will be lost too.

•Check that you have received all the product components before its installation. If you haven’t, contact us

immediately.

•Problems caused by a user mistake in the installation or manipulation of the product suppose the warranty

invalidation.

•Vag-Navisystems S.L. WON’T make responsible about the product damages caused by a wrong installation or an

improper use of the product.

You must note the manufacturer regulations for the manipulation of electric components, and the disconnection

of the airbags and the dismantling procedures of interiors or pieces needed to perform the installation.

1. Component identification:

1.1.Multimedia Interface components:

Multimedia Interface

Video source switch cable (OPTIONAL)

Power cable

AV sources wiring harnesses

(DTV_Cable_in + DVD_Cable_in)

Touch panel cable – TP IN

Vehicle’s screen connection cable

Extension cable for the original

wiring harness from the screen

to the multimedia interface

1.2.GPS Box components:

1.3.Voice module components:

GPS Box

Touch Panel

GPS Box power cable

GPS antenna

Hidden microphone

(Specific for overhead courtesy lights panel)

Speaker (OPTIONAL)

USB extension cable

Voice module

Voice module audio cable

Quadlock connection cable

to the voice module

2 Installation

2.1. Disassembling cockpit parts:

1) Monitor’s covert trim (models until 2011)

1) Monitor’s covert trim (2012 onwards)

Use removal wedge -3409- to prise off cover -1- for MMI

screen at corners -arrows- and detach.

Unplug electrical connector for warning lamp for airbag

deactivated on front passenger side -K145- / hazard warning

lights button -E229- and detach cover.

Insert hook -T40207- carefully between louvres and engage

at side of vent.

Carefully disengage vent at sides -arrow A-.

A hole is provided on both sides of the vent for engaging

the hook -T40207-.

Carefully unclip cover -1- for MMI screen from dash panel

at top -arrows- and remove it as arrows shou, using a

-3409- wedge and pulling on the edges.

Unplug electrical connector for warning lamp for airbag

deactivated on front passenger side -K145- / hazard

warning lights button -E229- and detach cover for MMI

screen.

Remove carefully from the center of the dash vent, located

on the cockpit, -1- pulling from both sides with the -3438-

removal hook.

A hole is provided on both sides of dash panel vent for

engaging hook -3438-.

Equipment version with light: Unplug electrical connector

at dash panel vent.

Switch off ignition

Position the hook -3438--A- as shown in one of the

openings -B- or -C- of the air conditioner operating and

display unit, Climatronic control unit -J255-.

Carefully pull air conditioner operating and display unit

(Climatronic control unit -J255-) out of centre console in

direction of -arrow-.

Note

The air conditioner operating and display unit (Climatronic

control unit -J255-) is held in position by the clips (left and

right) in the centre console support brackets.

a) Remove bolts -arrows- at radio -R--1-.

b) Pull radio -R--1- out of dash panel.

c) Release and unplug connectors at radio -R-.

Unscrew screws of the monitor -arrow-, monitor with

controls for managing the information, in front -J685--1-.

Pull up the monitor from the dashboard -2-.

Unlock and disconnect the screen connectors.

Remove side dash panel cover (passenger side).

Open glove box lid and unscrew bolts -arrows-.

Detach glove box and pull it out far enough so that you

can unplug electrical connector at main connector.

2.2 Performing the NaviTouch® system installation:

Now we are going to prepare the “TOUCH SCREEN” to the original vehicle screen.

1) Unscrew the 4 screws of the screen’s metal frame.

2) Clean the screen with a non-abrasive cleaner and a microfiber cloth, then, immediately place the touch

screen panel.

Place the touch screen above, and screw again the screws that you have removed a before. DON’T tighten too much

the screws because you could break the touch screen or damage it and make it work wrong because of the central

pressure. Center it, and make the connection cable of the touch screen pass under the frame.

NOTE: Some of the touch screen incorporate a protection film, remove it before.

3) Join the touch screen 4-wire cable to the Brown connector of the “Touch panel cable” (TP IN)

that is connected into the “TP IN” port of the Multimedia interface.

NOTE: Make sure that the 4-wire (golden metallic part) is right connected to the 4 metallic pin of

the brown tap connector before you close it.

4) Connect the “Vehicle’s screen connection cable”, to the female connector of the “Extension cable for the original

wiring harness from the screen to the multimedia interface”.

5) Connect the other side of the “Extension cable for the original wiring harness from the screen to the multimedia

interface” to the “LCD-IN” port of the Multimedia interface.

6) Connect the “Vehicle’s screen connection cable“ to the multimedia interface “TO-LCD” port.

7) Connect the “Vehicle’s screen connection cable “ from the multimedia interface to the vehicle’s screen.

Otros manuales para NaviTouch

Tabla de contenidos

Otros manuales de Sistema de vídeo para coche de VAG-Navisystems

VAG-Navisystems

VAG-Navisystems NaviTouch A1-Q3 Manual

Manuales populares de Sistema de vídeo para coche de otras marcas

Stinger

Stinger HEIGH10 RB10RAM13B Manual de usuario

Eonon

Eonon E1057 Manual de usuario

Milion

Milion D2223 Manual de usuario

Metra Electronics

Metra Electronics 99-8153 Manual de usuario

Voxx Electronics

Voxx Electronics HR8MA1 Manual de usuario

Axxera

Axxera AV604Bi Manual de usuario

Clarion

Clarion NX706E Manual de usuario

Pyle view

Pyle view PLDN74BTi Manual de usuario

Clarion

Clarion NX602 Manual de usuario

PowerAcoustik

PowerAcoustik PTID-5850N Manual de usuario

RCA

RCA DRC6296 - Twin 9" Mobile DVD System Guía del usuario

Lanzar

Lanzar SVDVD5 Manual de usuario

Kia

Kia MTXM100YPPE Manual de usuario

Eonon

Eonon E1060 Manual de usuario

Macrom

Macrom M-AN900 Manual de usuario

Hyundai

Hyundai BAPE-L3000N Manual de usuario

r.LiNK

r.LiNK RL2-UCON8-SM Manual de usuario

Blaupunkt

Blaupunkt DVP 01C Manual de usuario