V-tech BLUEY JOTBOT Manual de usuario
Instruction
Manual
Included in the Package
* 2 of the data chips are for saving codes in Code-to-Draw mode.
3
WARNING:
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties, cords and packaging screws are not part of
this toy and should be discarded for your child’s safety.
WARNING:
Please save this Instruction Manual as it contains important information.
1 JotBot 15 Double-sided
Drawing Data Chips*
1 Guidebook
1 Storage Box
1 Child-Friendly
Felt Tip Pen
Features
Switch to either or to power JotBot ON.
Switch to to power JotBot OFF.
Press this to confirm, to start an activity or to start drawing.
Command JotBot to move forwards (north) in Code-to-Draw mode.
Command JotBot to move backwards (south) in Code-to-Draw mode.
Command JotBot to move to your left (west) in Code-to-Draw mode.
It can also turn the volume down in other modes.
Command JotBot to move to your right (east) in Code-to-Draw mode.
It can also turn the volume up in other modes.
Command to toggle JotBot’s pen position up or down in
Code-to-Draw mode.
Press this to cancel or to exit an activity.
Animated Face
Control Panel
Power /
Mode Switch
Speaker
Data chip slot
Battery compartment
Pen
Holder
4
5
INSTRUCTIONS
BATTERY REMOVAL AND INSTALLATION
1. Make sure the unit is turned OFF.
2. Locate the battery cover at the bottom of the unit. Use a screwdriver
to loosen the screws and then open the battery cover.
3. If used batteries are present, remove these
batteries from the unit by pulling up on one
end of each battery.
4. Install 4 new AA (AM-3/LR6) batteries
following the diagram inside the battery
box. (For best performance, alkaline
batteries are recommended.
Rechargeable batteries are not
guaranteed to work with this product).
5. Replace the battery cover and tighten the screws to secure.
IMPORTANT: BATTERY INFORMATION
• Insert batteries with the correct polarity (+ and -).
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable batteries.
• Only batteries of the same or equivalent type as recommended are to
be used.
• Do not short-circuit the supply terminals.
• Remove batteries during long periods of non-use.
WARNING:
Adult assembly required for battery installation.
Keep batteries out of reach of children.
Switch to either or to power JotBot ON.
Switch to to power JotBot OFF.
Press this to confirm, to start an activity or to start drawing.
Command JotBot to move forwards (north) in Code-to-Draw mode.
Command JotBot to move backwards (south) in Code-to-Draw mode.
Command JotBot to move to your left (west) in Code-to-Draw mode.
It can also turn the volume down in other modes.
Command JotBot to move to your right (east) in Code-to-Draw mode.
It can also turn the volume up in other modes.
Command to toggle JotBot’s pen position up or down in
Code-to-Draw mode.
Press this to cancel or to exit an activity.
TROUBLESHOOTING
If for some reason the program/activity stops working or malfunctions,
please follow these steps:
1. Please turn the unit OFF.
2. Interrupt the power supply by removing the batteries.
3. Let the unit stand for a few minutes, then replace the batteries.
4. Turn the unit ON. The unit should now be ready to play with again.
5. If the product still does not work, install a brand new set of batteries.
If the problem persists, please contact our Consumer Services Department,
and a service representative will be happy to help you. 6
• Remove exhausted batteries from the toy.
• Dispose of batteries safely. Do not dispose of batteries in fire.
RECHARGEABLE BATTERIES:
• Remove rechargeable batteries from the toy before charging.
• Rechargeable batteries are only to be charged under adult
supervision.
• Do not charge non-rechargeable batteries.
CARE & MAINTENANCE
1. Keep the unit clean by wiping it with a slightly damp cloth.
2. Keep the unit out of direct sunlight and away from any direct heat
sources.
3. Remove the batteries if the unit will not be in use for an extended
period of time.
4. Do not drop the unit on hard surfaces and do not expose the unit
to moisture or water.
7
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and
batteries, or on their respective packaging, indicates they
must not be disposed of in domestic waste as they contain
substances that can be damaging to the environment and
human health.
The chemical symbols Hg, Cd or Pb, where marked, indicate
that the battery contains more than the specified value of
mercury (Hg), cadmium (Cd) or lead (Pb) set out in the
Batteries and Accumulators Regulation.
The solid bar indicates that the product was placed on the
market after 13th August, 2005.
Help protect the environment by disposing of your product or
batteries responsibly.
VTech®cares for the planet.
Care for the environment and give your toy a second life by disposing
of it at a small electricals collection point so all its materials can be
recycled.
In the UK:
Visit www.recyclenow.com to see a list of collection points near you.
In Australia & New Zealand:
Check with your local council for kerbside collections.
Getting Started
Insert Batteries
(To be done by an adult)
1
• Locate the battery compartment at the bottom of JotBot.
• Loosen the screws of the battery cover using a screwdriver.
• Insert 4 AA alkaline batteries as indicated inside the
battery compartment.
• Replace the battery cover and tighten the screws.
See p.4 for more information about battery installation.
8
Install Pen
2
• Place a scrap sheet of paper under JotBot.
• Turn On JotBot.
• Remove the cap of the bundled pen and insert it into the
pen holder.
• Push the pen gently down until it reaches the paper, and
then release the pen. The pen should rebound slightly
above the paper by around 1-2mm.
NOTE: To prevent the pen's ink from drying, please
replace the cap of the pen when it is not in use for a long
period of time.
9
1-2mm
10
Setup Paper
3
• Prepare an A4 or larger sheet of paper.
• Place it on a flat, level surface. Keep the paper at
least 10cm away from the edge of the surface to
avoid JotBot from falling.
• Clear any obstacles on or near the paper. Then, place
JotBot in the centre of the paper before JotBot begins
to draw.
NOTE: Tape the 4 corners of the paper to the surface for
the best drawing performance. Put an extra piece of
paper on the surface to protect the surface from staining.
Tabla de contenidos
Otros manuales de Juguete de V-tech
V-tech
V-tech Peek-A-Boo Ball Manual de usuario
V-tech
V-tech Jungle Gym: Step & Count Kangaroo Manual de usuario
V-tech
V-tech iDiscover App Panda Manual de usuario
V-tech
V-tech Tote & Trace Drawing Board Manual de usuario
V-tech
V-tech Fly & Learn Airplane Manual de usuario
V-tech
V-tech SWITCH & GO DINOS Manual de usuario
V-tech
V-tech V.Smile: Superman The Greatest Hero Manual de usuario
V-tech
V-tech SmartVille - Safe & Sound Fire Station Manual de usuario
V-tech
V-tech Toot-Toot Animals Farm Manual de usuario
V-tech
V-tech V.Smile: Elmo's World Manual de usuario
V-tech
V-tech 80-056000 - Baby Call Count Phone Manual de usuario
V-tech
V-tech V.Smile: Go Diego Go Save the Animal... Manual de usuario
V-tech
V-tech Bear's Dress & Discover Book 5583 Manual de usuario
V-tech
V-tech 2-in-1 Musical Mobile Manual de usuario
V-tech
V-tech Counting Time Measuring Tape Manual de usuario
V-tech
V-tech Let's Go Rescue Pup Manual de usuario
V-tech
V-tech Smart Start Learning Laptop Manual de usuario
V-tech
V-tech Musical Rhymes Book Manual de usuario
V-tech
V-tech V.Smile: The Lion King Simba s Big Adventure Manual de usuario
V-tech
V-tech ABC Learning Apple Manual de usuario
