V-tech Alphabet Train Manual de usuario
© 2012 VTech
Printed in China
91-002305-035
User’s Manual
Alphabet Train
tm
US CA
3
INTRODUCTION
Thank you for purchasing the VTech®Sit-to-Stand Alphabet Train™
learning toy!
The VTech®Sit-to-Stand Alphabet Train™will take your child on a
journey through letters, numbers, music and more. Entertaining sound
effects, dancing lights and fun melodies reward your child’s curiosity
while taking baby on the ride of a lifetime!
Introduction
NUMBER
BUTTONS
13 LETTER
BLOCKS
BOOK WITH
6 PAGES
ATTACHABLE
CARRIAGE WITH
BLOCK STORAGE
OFF/MODE
SELECTOR
SWITCH
BLOCK
CHUTE
BLOCK
VOLUME
CONTROL
SWITCH
RECOGNITION
SLOTS
4
INCLUDED IN THIS PACKAGE
- One engine
- One engine handle
- Two back engine wheels
- One soft hinge with two screws
- One instruction manual
Included in This Package
- Four carriage wheels on
axles, four axle covers
and eight screws
- 13 alphabet blocks
- Two front engine wheels
- One carriage
5
WARNING: All packing materials, such as tape, plastic sheets,
packaging locks and tags are not part of this toy, and
should be discarded for your child’s safety.
Attention : Pour la sécurité de votre enfant, débarrassez-vous
de tous les produits d’emballage tels que rubans
adhésifs, feuilles de plastique, attaches et étiquettes.
Ils ne font pas partie du jouet.
NOTE: Please keep this instruction manual as it contains important
information.
GETTING STARTED
BATTERY INSTALLATION
1. Make sure the unit is turned OFF.
2. Locate the battery cover on the back of
the unit. Use a coin or a screwdriver to
loosen the screw.
3. Install 3 new ‘AA’ (AM-3/LR6) batteries
following the diagram inside the battery
box.
4. Replace the battery cover and tighten
the screw to secure the battery cover.
BATTERY NOTICE
• Use new alkaline batteries for maximum performance.
• Use only batteries of the same or equivalent type as recommended.
• Do not mix different types of batteries: alkaline, standard (carbon-
zinc) or rechargeable (Ni-Cd, Ni-MH), or new and used batteries.
• Do not use damaged batteries.
• Insert batteries with the correct polarity.
• Do not short-circuit the battery terminals.
• Remove exhausted batteries from the toy.
• Remove batteries during long periods of non-use.
Getting Started
6
Assembly Instructions
• Do not dispose of batteries in fire.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the toy before charging (if
removable).
• Rechargeable batteries are only to be charged under adult
supervision.
With the VTech
®
Sit-to-Stand Alphabet Train
™
, safety comes first.
To ensure your child’s safety, adult assembly is required.
Attention: ce jouet doit être assemblé par un adulte !
Assurez-vous que toutes les parties sont correctement assemblées
avant usage.
Assembly Instructions
1. Install the two green front wheels onto
the front of the engine by placing them
over the yellow front axles. Push the
wheels onto the axles until you hear
a click. Once you have installed the
wheels, they cannot be removed.
2. Install the two green back engine
wheels onto the back of the engine by
inserting them into the yellow sockets
at the back of the train.Push the wheels
into the sockets until you hear a click.
Once you have installed the wheels,
they cannot be removed.
7
3. Insert the green carriage wheels on axles into the corresponding
grooves on the bottom of the carriage. Place the blue axle covers
over the axles with the flat side up and the notched side between the
screw holes and the blue tabs on the bottom of the carriage. Slide
the axle covers toward the wheels, making sure the flat side slides
under the tabs and the screw holes align with those on the carriage.
Insert the screws into the holes and tighten with a screwdriver to
secure.
4. Position the handle so that the curved
part of the handle faces the back of
the engine. Insert the handle into the
hole in the top of the engine until you
hear a click. Once you have installed
the handle, it cannot be removed.
5. Position the soft, blue hinge so that its large hole is facing up and to
the front. Insert the hinge into the hole at the front of the carriage,
use a screwdriver to tighten the two screws on the bottom of the
carriage.
Assembly Instructions
8
6. To attach the carriage to the engine,
insert it into the slot at the back of
engine. You will hear a click, which
lets you know the carriage is attached
correctly.
7. To detach the carriage from the engine, press and hold the blue
button under the end of the engine, pull the carriage from the slot.
PRODUCT FEATURES
1. OFF/MODE SELECTOR SWITCH
To turn the unit ON, slide the red OFF/
MODE SELECTOR SWITCH located at
the top of the engine to the Learning
Mode ( ) or Discovery Mode ( )
position. To turn the unit OFF, slide the
OFF/MODE SELECTOR SWITCH to
the OFF ( ) position.
Product Features
9
2. VOLUME CONTROL SWITCH
To adjust the volume, slide the
VOLUME CONTROL SWITCH to the
LOW VOLUME or the HIGH VOLUME
position.
3. AUTOMATIC SHUT-OFF
To preserve battery life, the VTech®Sit-to-Stand Alphabet Train™
will automatically power-down after approximately 78 seconds
without input.The unit can be turned on again by pressing any button.
ACTIVITIES
1. Slide the red off/mode selector switch
located at the top of the engine to the
Learning Mode ( )or Discovery
Mode ( ) position to turn the unit on.
You will hear a train engine sound,
entertaining phrases and music. The
lights will flash with the sounds.
2. Press the elephant button to hear an
elephant sound effect followed by fun
phrases and sung songs.The lights will
flash with the sounds.
Activities
10
3. Press the number buttons to learn
about numbers in the Learning Mode
and learn about colors in the Discovery
Mode. The lights will flash with the
sounds.
4. Turn the book’s pages to learn about
letters and objects and listen to fun
stories in both modes. The lights will
flash with the sounds.
5. Place the blocks onto the train’s block
recognition slots to learn letters and
objects in both modes. Upbeat melodies
and fun sounds will accompany the play.
The lights will flash with the sounds.
6. Drop the blocks into the chute at the
top of the train and they’ll slide out the
back!
7. If there is no input to the unit after approximately 10 seconds, you
will hear a fun sung song. After another 10 seconds if there is still
no input, you will hear a question, which will encourage the child to
find the correct block according to the book page. After another 10
seconds if there is still no input, you will hear the phrase “Bye-bye,”
then the unit will automatically power-down.
Activities
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Juguete de V-tech
V-tech
V-tech Touch & Swipe Baby Phone - Pink Manual de usuario
V-tech
V-tech Cutie Paws Puppy Stroller Instrucciones de montaje
V-tech
V-tech V.Smile: Disney/Pixar Cars Rev It Up in Radiator... Manual de usuario
V-tech
V-tech Go! Go! Cory Carson Fire Rescue Freddie Manual de usuario
V-tech
V-tech Pop 'n Sing Apple Manual de usuario
V-tech
V-tech Go! Go! Smart Friends Sweet Surprises Treat... Manual de usuario
V-tech
V-tech Move & Zoom Racer Manual de usuario
V-tech
V-tech Marble Rush Ultimate Set 5423 Manual de usuario
V-tech
V-tech Touch & Imagine Block Manual de usuario
V-tech
V-tech Sing and Soothe Mobile Manual de usuario
V-tech
V-tech Brilliant Baby Laptop Manual de usuario
V-tech
V-tech Count with Me Hippo Manual de usuario
V-tech
V-tech 80-073800 - Babys Learning Laptop Manual de usuario
V-tech
V-tech Go! Go! Cory Carson The Carson Playhouse Instrucciones de montaje
V-tech
V-tech Toot-Toot Drivers Train Set Instrucciones de montaje
V-tech
V-tech Voyager Adventure System Manual de usuario
V-tech
V-tech Princess Magical Learning Wand Manual de usuario
V-tech
V-tech Touch & Learn Activity Desk Manual de usuario
V-tech
V-tech Snuggle and Cuddle Fox Instrucciones de montaje
V-tech
V-tech Pop-A-Ball Pop & Play Tower Instrucciones de montaje
