V-tech IP8100-1 Manual de usuario
IP8100 series Quick Start Guide
www.vonage.com/vtech
The IP8100 series telephone is an advanced broadband cordless telephone set, capable of supporting up to
four handsets.
Your package contains:
1. Base Unit 6. Charger Wall Mounting Bracket(s)
2. Handset(s) 7. Belt Clip(s)
3. Handset Charger(s) 8. User Documentation CD
4. Ethernet Cables 9. Quick Start Guide
5. Base Power Adapter 10. Battery(ies)
Parts Check List
Base Unit
Handset
Blue Ethernet Cable
Charger Wall
Mounting Bracket
User Documentation
CD
Handset Charger
Base AC Power Adapter
Belt Clip
Battery
Quick Start Guide
1
Yellow Ethernet Cable
i : Your broadband telephone accommodates up to 4 handsets. You can add new handset, model# IP811, by
visiting www.vtechphones.com or call VTech Communications Inc. at 800-595-9511.
IP8100 series Quick Start Guide
Getting Started
Installation of Batteries in Handset
Follow the steps below:
1. Place the new battery in the handset and align
the two holes in the plug with the socket pins to
snap the plug into place.
2. Replace the battery cover by sliding it upwards.
3. If the new batteries are not already charged,
place the handset in its charger, and allow it to
charge for 10-12 hours. After initial charge, a
maintenance charge of 8 hours should be sufficient.
NOTE: Use VTech battery 80-5808-00-00 or VTech
Replacement 89-1324-00-00. To purchase replacement batteries,
visit us on the web at www.vtechphones.com or call VTech Communications, Inc. at 800-595-9511.
Charging of the Handset Batteries
The handset of your cordless telephone is powered
by rechargeable batteries. It charges automatically
whenever handset is in its charger.
You should charge the batteries for 10-12 hours
when you first receive your phone. You will know
the batteries need charging when:
• The low battery message is displayed.
• The handset seems completely dead, the LCD
is completely clear and does not activate
when you press the keys.
2
• IMPORTANT •
BEFORE YOU BEGIN: Make sure that you have installed and fully charged the handset batteries.
IP8100 series Quick Start Guide
Getting Started
Pre-Installation
Answer the following questions for the instructions that are appropriate for you.
Do you have a stand-alone router?
If yes, please use the instructions on page 7.
Helpful Hint: Do you have more than one computer connected to the Internet? If so,
you have a router.
Do you have a modem with a built in router?
If yes, please use the instructions on page 9.
Helpful Hint: Some Internet Service Providers (ISP) supply combinations modem/
routers. Please look on the back of your modem, if it has multiple ports, it is a modem with
a built in router. If you are not sure, please call your ISP and ask them if it is a standard
modem or a modem with a built in router and follow the appropriate instructions.
If the answer is no to both questions, continue on page 4.
Helpful Hint: If you purchased this VTech broadband phone from a retail store, you
need to activate your device at www.vonage.com/activate.
3
PC
DSL or Cable Modem
INTERNET
Base Unit
Handset 1 & 2
NOTE: The IP8100 series telephone is expandable up to
a total of 4 handsets. Uses model IP 811 (sold separately)
WAN Port
4
Installation Without A Router
Warning: Do not route the ethernet cable to outdoors, and ensure that you are using a safety approved
DSL or Cable modem with proper electrical isolation.
PC/LAN Port
STEP 1
Unplug the power cord from your Cable or DSL modem (the device your ISP provided which provides high-speed
Internet). Make sure that you turn your computer off and that you do NOT plug in your broadband telephone until
instructed to do so.
Helpful Hint: The modem should be powered off for at least 10 minutes. If it is turned off for a shorter period
of time, it may “remember” old information that will prevent it from working properly.
5
IP8100 series Quick Start Guide
Installation Without A Router
STEP 4
Connect one end of the blue ethernet cable to the blue port, labeled “WAN,” located on the back of the base unit and
connect the other end of the blue cable to the ethernet port on your cable or DSL modem.
STEP 5
Reconnect power cord to the modem then turn the modem on. Please wait until all lights on the modem stop blinking.
Helpful Hint: This should take a few minutes, but may take as long as 10 minutes.
STEP 6
Plug the power cord into the power port located on the bottom or your IP8100 series telephone and the other end into
the electrical outlet. This turns the IP8100 series broadband telephone on.
Helpful Hints:
DO NOT interrupt this registration process by unplugging the power or by using the handsets until the READY indica-
tor light on the front of base has gone from flashing yellow to a steady green.
Use only the power cord provided in this package; using an older power cord can damage the broadband telephone.
STEP 7
Turn your computer on, and check your computer to see if your Internet is working, try to visit any website. If your
Internet is working, please proceed to STEP 9. If not, please proceed to STEP 8.
STEP 2
Disconnect all cables between your Cable or DSL modem and your computer.
STEP 3
Connect one end of the yellow ethernet cable to the yellow port, labeled “PC/LAN,” located on the back of the base
unit and connect the other end of the yellow cable to the ethernet port of your computer.
STEP 8:
Cable Users
If you receive Internet access through a Cable modem, you may need to register the IP8100 series telephone with
your ISP. Please contact them to update your information; you will likely need your WAN MAC address, which is
located on the bottom of the IP8100 series telephone. Once your ISP has updated your account, proceed to step 9.
-- OR --
Installation Without A Router cont’
6
DSL Users
If you have DSL and are required to enter a user name and password (PPPoE) when accessing the Internet, you may
be required to authenticate the IP8100 series telephone.
A. Open a web browser such as Microsoft ® Internet Explorer using the computer connected through your
IP8100 series telephone ethernet port. In the address of location field, type <http://192.168.15.1> and
press ENTER. This displays the login screen. Enter the default password ‘VTech’ and click on login.
B. On the Setup Wizard screen, click Run Wizard to start the set-up.
C. Follow Wizard screens to complete the setup.
STEP 9:
Check for dial tone by pressing the ON button on your handset. If you do not hear a dial tone, please refer to the
Troubleshooting section of the user manual.
Congratulations! Even if you are transferring your number, you are ready to start taking advantage of the great sav-
ings and superior quality of Vonage right now! Please call 800-342-1791 to setup your voicemail service and to learn
about other free Vonage features included with every Vonage calling plan.
DSL or Cable Modem
INTERNET
Existing
Network Router
Laptop
PC
Base Unit
Handset 1 & 2
NOTE: The IP 8100 series telephone is expandable up to
a total of 4 handsets. Uses model IP 811 (sold separately)
WAN Port
7
IP8100 series Quick Start Guide
Warning: Do not route the ethernet cable to outdoors, and ensure that you are using a safety approved DSL or
Cable modem with proper electrical isolation.
Installation With A Router
IP8100 series Quick Start Guide
8
Installation With A Router
STEP 1:
Using the blue ethernet cable provided, connect one end into the blue port, labeled “WAN,” located on the back of the
IP8100 series broadband telephone base unit and connect the other end into an available LAN port on your router.
If you have a wireless router, place the base unit at least 3’ away from your router to avoid interference.
Helpful Hint: If all the ethernet ports on your existing router are full, disconnect one of the attached devices
from the existing router. Plug the blue ethernet cable into the now free port on your router. Connect the device
you just unplugged from your router to the yellow “PC/LAN” port located on the back of IP8100 series broadband
telephone base unit.
STEP 2:
Plug the power cord into the power port located on the bottom of your base unit and the other end into the electrical
outlet. This turns the IP8100 series broadband telephone on.
Helpful Hint: DO NOT interrupt this registration process by unplugging the power or by using the handsets until
the READY indicator light on the front of base has gone from flashing yellow to a steady green.
Helpful Hint: Use only the power cord provided in this package; using an older power cord can damage the
broadband phone.
STEP 3:
Check for dial tone by pressing the ON button on your handset. If you do not hear a dial tone, please refer to the
Troubleshooting section of the user manual.
Congratulations! Even if you are transferring your number, you are ready to start taking advantage of the great sav-
ings and superior quality of Vonage right now! Please call 800-342-1791 to setup your voicemail service and to learn
about other free Vonage features included with every Vonage calling plan.
DSL or Cable Modem
INTERNET
Laptop
PC
Base Unit
Handset 1 & 2
NOTE: The IP8100 series telephone is expandable up to
a total of 4 handsets. Uses model IP 811 (sold separately)
WAN Port
9
IP8100 series Quick Start Guide
Warning: Do not route the ethernet cable to outdoors, and ensure that you are using a safety approved DSL or
Cable modem with proper electrical isolation.
Installation With A Modem Router
Otros manuales para IP8100-1
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Teléfono de V-tech
V-tech
V-tech CS6428-32 Manual de usuario
V-tech
V-tech EriseBusinessSystem UP406 Manual de usuario
V-tech
V-tech ErisTerminal VSP610AErisTerminal VSP608A Manual de usuario
V-tech
V-tech CD1113 Manual de usuario
V-tech
V-tech CD1281 Manual de usuario
V-tech
V-tech Vonage IP 8100-2 Manual de usuario
V-tech
V-tech SN6127 Manual de usuario
V-tech
V-tech 17450 Manual de usuario
V-tech
V-tech IP5821 Manual de usuario
V-tech
V-tech ES1000-B Manual de usuario
V-tech
V-tech CS6428-2 Manual de usuario
V-tech
V-tech S1310 Manual de usuario
V-tech
V-tech ia5824 Manual de usuario
V-tech
V-tech ErisTerminal VSP726A Manual de usuario
V-tech
V-tech VT1121 Manual de usuario
V-tech
V-tech CS6147 Manual de usuario
V-tech
V-tech CL80121 Manual de usuario
V-tech
V-tech A2211 Manual de usuario
V-tech
V-tech i5868 Manual de usuario
V-tech
V-tech i6720 Manual de usuario
