Utility Solutions BREAK-SAFE 600 Instrucciones de instalación

Phone (828)323-8914

Fax (828)323-8410

Email [email protected]

Web www.utilitysolutionsinc.com

101 33rd Street Drive SE · Hickory, NC 28602

C-01051

USBS-600-1

Field Inspection (2-24-16)

FIELD INSPECTION PROCEDURE

BREAK-SAFE

600 Load Break & Pick-up Tool

USBS-600-1

Follow the steps below before EACH use of the BREAK-SAFE® 600.

This procedure does NOT replace or eliminate periodic maintenance.

Visually inspect the tool. If any of the following are

found, remove the tool from the eld and perform

service:

• Soot or Dirt buildup on

components

• Damaged Load Break

Ring. Ring should rotate

freely (shaft should NOT

rotate)

• Damaged or discolored

Yellow Tube

• Damaged Conductor

Hook

• Loose Conductor Bars

• Damaged Safety Locking

• Out of Date Maintenance

Decal (service should be

performed within 2 years

of date shown)

Test both Conductor Bars.

A) With the tool in the CLOSED position, use a voltmeter,

conrm continuity exists between a Conductor Bar and the

Conductor Hook.

B) Conrm continuity exists while pulling the Load Break

Ring toward the open position. Continuity should exist until

the load break mechanism is engaged and the tool locks in

the open position.

C) Conrm NO continuity exists between a Conductor Bar

and the Conductor Hook when the tool is in the fully opened

positioned.

! !

WARNING

Carefully read and fully understand the manual prior to

operating, maintaining or testing this device. Improper

operation, handling or maintenance of this device can result

in death, grievous personal injury and or equipment damage.

Exert a steady downward movement on the Load Pick-up Trigger

(D). The Load Break Ring Assembly should retract forcefully into

the tool.

Push the Load Break Ring up into the tool rmly to reset

(E).

An internal safety mechanism will not allow the Load Break

Ring to extend until the tool has been reset. The tool will

require service and should NOT be used if the Load Break

Ring cannot extend after resetting.

VISUAL INSPECTION

CONTINUITY

SAFETY RESET

0.25

---

0.25

The BREAK-SAFE® will reset when the Load Break

Ring Assembly has fully retracted inside the tool.

A current path will exist inside the tool until the load

break mechanism is triggered.

PATENT NO. 6,078,008 Other Patents Pending

Phone (828)323-8914

Fax (828)323-8410

Email [email protected]

Web www.utilitysolutionsinc.com

101 33rd Street Drive SE · Hickory, NC 28602

C-01051

USBS-600-1

Field Inspection (2-24-16)

UNLOCKED

CLOSED

OPEN

CLOSED

OPEN

FIELD INSPECTION PROCEDURE

BREAK-SAFE®600 Load Break & Pick-up Tool

! !

DANGER

Refer to Inspection Procedure on reverse side and the Operation Manual

for complete instructions on properly resetting the BREAK-SAFE® 600.

LOCKED

! !

WARNING

Always remove the BREAK-SAFE® 600 from the circuit, or remove the jumpers attached

to the conductor bars, aer each load break operation.

e BREAK-SAFE® 600 is not rated insulation nor is it considered a “visible gap”.

Conductor

Hook

Load Pick-up Trigger

Conductor Bar

Load Break Ring

(should rotate freely)

Safety

Locking Pin

Conductor Bar

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas de Utility Solutions

Utility Solutions

Utility Solutions BREAK-SAFE USBS-15-1-PS Manual de usuario

Utility Solutions

Utility Solutions LOAD-RANGER USLR-XLT-1 Manual de usuario

Utility Solutions

Utility Solutions BREAK-SAFE 600 Instrucciones de instalación

Utility Solutions

Utility Solutions BREAK-SAFE USBS-15-1 Instrucciones de instalación

Utility Solutions

Utility Solutions LOAD-RANGER USLR-XLT-1 Manual de usuario

Utility Solutions

Utility Solutions Jack Jumper USJJ-005 Manual de usuario

Utility Solutions

Utility Solutions Jack Jumper USJJ-004 Manual de usuario

Utility Solutions

Utility Solutions Jack Jumper SMD-20 Manual

Utility Solutions

Utility Solutions LOAD-RANGER USLR-XLT-1 Instrucciones de instalación

Utility Solutions

Utility Solutions Jack Jumper USJJ-004 Manual de usuario

Utility Solutions

Utility Solutions BREAK-SAFE USBS-15-2-PS Manual de usuario

Utility Solutions

Utility Solutions Jack Jumper USJJ-007 Manual de usuario

Utility Solutions

Utility Solutions Jack Jumper USJJ-002 Manual de usuario

Utility Solutions

Utility Solutions LOAD-RANGER FLEX-LT Load Break Tool Manual de usuario

Utility Solutions

Utility Solutions Jack Jumper USJJ-006 Manual de usuario

Utility Solutions

Utility Solutions Jack Jumper USJJ-003 Manual de usuario

Utility Solutions

Utility Solutions LOAD-RANGER FLEX-LT Manual de usuario

Utility Solutions

Utility Solutions BREAK-SAFE USBS-15-1-PS Manual de usuario

Utility Solutions

Utility Solutions BREAK-SAFE USBS-15-1-PS Instrucciones de instalación

Utility Solutions

Utility Solutions Jack Jumper USJJ-006 Manual de usuario

Utility Solutions

Utility Solutions Jack Jumper USJJ-001 Manual de usuario

Utility Solutions

Utility Solutions Jack Jumper USJJ-003 Manual de usuario

Utility Solutions

Utility Solutions LOAD-RANGER XLT Series Manual de usuario

Utility Solutions

Utility Solutions Jack Jumper Manual de usuario

Manuales populares de Herramientas de otras marcas

Martor

Martor SECUNORM 175 Manual de usuario

ERKCO

ERKCO 1000 Manual de usuario

jbc

jbc N4473 Manual de usuario

FEINMETALL

FEINMETALL FZWZ-SET-001 Manual de usuario

Worx Professional

Worx Professional Sonicrafter WU676 Manual de usuario

Gage Bilt

Gage Bilt GB713SH Manual de usuario

Hilti

Hilti DX 9-ENP Manual de usuario

norbar

norbar NORTRONIC 34399 Manual de usuario

BGS technic

BGS technic 8578 Manual de usuario

Makita

Makita DHR241 Manual de usuario

Motor Guard

Motor Guard JMB-1250 Manual de usuario

Power Adhesives

Power Adhesives 805-12 Manual de usuario

Clemco

Clemco 24189 Manual de usuario

VVG

VVG VNG 903 Series Manual de usuario

Hilti

Hilti FX 3-A Manual de usuario

Grizzly

Grizzly H6472 Manual de usuario

axing

axing BWZ 5-02 Manual de usuario

Dh-Robotics

Dh-Robotics RGI-100 Cómo utilizar