Ustellar UT88875 Manual de usuario
Smart LED Flood Light User Guide
Manual Version: UT88875-RGBW / V1.0
(QJOLVK
Smart LED Flood Light User Guide
Before installation, let’s know how the whole thing works.
Step One: Install the smart flood light.
Step Two: Fundamental set-up-Connect smart LED flood light to Smart
Life App.
Step Three & Four: Optional set-up - Connect Smart Life App to Amazon
Alexa or Google Assistant.
After completing Step Two, you can remote control the light on Smart Life App.
After completing Step Three and Four, you can voice control the light with
Alexa or Google Assistant. This manual consists of Four parts.
Part One - How to install the light ?··························2 - 7
Part Two - How to pair the light to Smart Life app?·············8 - 13
Part Three - How to control the light with Amazon Alexa? ······ 14 - 16
Part Four - How to control the light with Google Assistant?·····17 - 18
Voice Control
Voice Control
1
(QJOLVK
Part One - How to insall the light?
Warning
1 Please check if the light and the parts are intact before installation.
2 Make sure to cut o power before installation.
3 Please do not place this light in corrosive conditions.
4 If there is any damage to the cord, please cut o the power and stop
using it immediately.
5 Please do not retrofit the light within the warranty period.
6 To ensure the light works properly, please use the voltage indicated
on the packing.
2
Model
Total Waage
Max Luminous Flux
Input Voltage
Color
Color Temperature
Frequency
Bean Angle
Working temperature
Waterproof Rating
UT88875
40W
4000lm
RGB, Warm White
2700K
50/60Hz
120°
-20~40燠
AC120V
1. Parameters
Flood Lights IP66
Power Adapter IP44
(QJOLVK
2. Components
3
Package Includes:
Flood Light
Power Adapter
Flood Lights
Power Adapter
Ground Sticks
Screws
L Shaped Hex Key Wrench
User Manual
x 6
x 1
x 1
x 1
x 6
x 7
(QJOLVK
3. Dimension
4
14cm/5.5in
3m/10ft 3m/10ft 3m/10ft
3m/10ft 3m/10ft
3m/10ft
3.2cm/1.26in
10cm/4.0in
12cm/4.7in 16cm/6.3in
Note:
1. The flood lights and cables can not be extended, Do not cut the cable.
2.Use this product with the provided power adapter only.
3. The power adapter is IP44 grade waterproof, which can not be directly
used outdoor. Please connect to a indoor socket, or use a waterproof box.
4. The flood lights are IP66 grade waterproof, which can be used outdoor.
But do not immerse the lights in water.
(QJOLVK
5
4. Installation
Step A: According to the spacing of two screw bits on the bracket, drill two
holes on the mounting panel.
A
B
Note: Maximum mounting height is over 5m.
Step B: Aim the bracket at the holes and fix it with two bolts (not included).
Step C: Adjust the lighting direction up or down as per your need and plug
in to power the light on.
C
Scenario 1:
(QJOLVK
6
Step A: Aach the ground stick to the Flood light, with the screw provided in
the package.
A
B
Step B: Tighten the screw with the Hex Key Wrench.
Step C: Adjust the lighting direction up or down as per your need and plug
in to power the light on.
C
Scenario 2:
7
01 Make sure that the distance between the light and the object being lits
is more than 1 meter, so as to avoid high temperature caused by short
distance.
1 This light is waterproof and damp proof. It is protected against the rain,
but it cannot be immersed in water.
2 The mounting position of this light should be able to bear at least 10
times as heavy as the light.
3 This light should be used in condition that is good for heat dissipation.
Its working temperature should be less than 45°C Too high the working
temperature will cause serious lumen depression and aect lifespan
of the light.
Note:
The light source of this Iuminaire is not replaceable.
Limitation of Indoor and Outdoor Use
01
FCC ID: 2AWONUT88875
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interferencethat may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with minimum distance of 20 cm between the radiator and your
body. This transmier must not be co-located or operating in conjunction
with any other antenna or transmier.
(QJOLVK
(QJOLVK
Step A : Smart Life app installation
Please choose either way below to download and install the app.
1 As per your phone system, choose the QR code to scan.
2 Search keyword ‘Smart Life’ in Apple Store or Google Play.
Step B Create an account on Smart Life and login.
Note: Please keep your account and password in mind for Alexa or Google
Assistant App pairing later.
Part Two - How to pair the light to
Smart Life app?
8
The WiFi signal receiving module is built in the first flood light head (the
one close to the power adapter). The maximum wireless connection
distance is up to 65ft/20m.
Before starting the paring, please make sure to turn on the Bluetooth and
WiFi on your phone.
The smart light only supports 2.4GHz WiFi network, not 5.0GHz. Please
make sure the working network is 2.4GHz, and your phone is connected
to it. If your WiFi router supports both 2.4GHz and 5.0GHz, please separate
the two frequency bands in the router seings, and select the 2.4GHz for
connection.
(QJOLVK
Step C : Add the light to Smart Life App
1. Tap ‘+’ buon on top right corner to add devices. Tap ‘Lighting’, then
choose ‘PIR Light BLE+Wi-Fi)’ to add the lights.
9
2. Power on the light with your own switch. Repeatedly turn on-o-on-o
-on-o-on switch 3 times) to activate the light into rapid blinking status
(about 0.5s per blink). Please make sure to keep an interval over 2 seconds
between each turn-on and turn-o. Then click the ‘Next’ buon on this
page. Find the lighting devices and click ‘+’.
Tabla de contenidos
Otros manuales de Foco de Ustellar
