UPSONIC POWER Tower UPS 6KS Manual de usuario

Tower / RT 6-10K

User Manual

Web: www.upsonic.com.au

Address: 9/20 Duerdin Street

Clayton VIC 3168

Phone: +61 3 9706 0045

Fax: +61 3 9706 8003

RELIABLE POWER SOLUTIONS FOR A NON-STOP WORLD

SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS. This manual contains important instrucons that

should be followed during installaon and maintenance of the UPS and

baeries.

The UPS models that are covered in this manual are intended for installaon in

an environment within 0 to 50°C, free of conducve contaminant.

Cerﬁcaon standards

• Safety: EN 62040-1

• EMC: IEC/EN 62040-2

• IEC 61000-4-2 (ESD): level 3.

• IEC 61000-4-3 (Radiated ﬁeld): level 3.

• IEC 61000-4-4 (EFT): level 4.

• IEC 61000-4-5 (Fast transients): level 4.

• IEC 61000-4-6 (Electromagnec ﬁeld): level 3.

• IEC 61000-4-8 (Conducted magnec ﬁeld): level 4.

• Performance: IEC/EN 62040-3

Special symbols

The following are examples of symbols used on the UPS or accessories to alert you

to important informaon:

RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric

shock symbol.

Important instrucons that must always be followed.

Do not discard the UPS or the UPS baeries in the trash.

This product contains sealed lead acid baeries and must be disposed as it's explain

in this manual. For more informaon, contact your local recycling/reuse or

hazardous waste center.

The crossed-out wheeled bin symbol indicates that waste electrical and electronic

equipment should not be discarded t ogether with unseparated household waste,

but must be collected separately. The product should be handed in for recycling in

accordance with the local environmental regulaons for waste disposal.

By separang waste electrical and electronic equipment , you will help reduce the

volume of waste sent for incineraon or land-ﬁlls and minimize any potenal

negave impact on human health and environment.

Informaon, advice, help.

Refer to the user manual.

Safety of persons

⚫ RISK OF VOLTAGE BACKFEED. The system has its own power source (the

baery). Isolate the UPS and check for hazardous voltage upstream and

downstream during lockout-tagout operaon. Terminal blocks may be

energized even if the system is disconnected from the AC power source.

⚫ Dangerous voltage levels are present within the system. It should be opened

exclusively by qualiﬁed service personnel.

⚫ The system must be properly grounded.

⚫ The baery supplied with the system contains small amounts of toxic

materials. To avoid accidents, the direcves listed below must be observed:

- Servicing of baeries should be performed or supervised by personnel

knowledgeable about baeries and the required precauons.

- When replacing baeries, replace with the same type and number of

baeries or baery packs.

- Do not dispose of baeries in a ﬁre. The baeries may explode.

- Baeries constute a danger (electrical shock, burns). The short -circuit

current may be very high.

⚫ Precauons must be taken for all handling:

- Wear rubber gloves and boots.

- Do not lay tools or metal parts on top of baeries.

- Disconnect charging source prior to connecng or disconnecng baery

terminals.

- Determine if baery is inadverte ntly grounded. If inadvertently grounded,

remove source from ground. Contact with any part of a grounded baery

can result in electrical shock. The likelihood of such shock can be reduced if

such grounds are removed during installaon and maintenance (ap plicable

to equipment and remote baery supplies not having a grounded supply

circuit).

Product safety

⚫ The UPS connecon instrucons and operaon described in the manual must

be followed in the indicated order.

⚫ CAUTION - To reduce the risk of ﬁre, the unit connects only to a circuit

provided with branch circuit overcurrent protecon for :

63A rang, for 6kVA models,

100A rang, for 10kVA models

The upstream circuit breaker for Normal AC/Bypass AC must be easily

accessible. The unit can be disconnected from AC power source by opening this

circuit breaker.

⚫ An addional AC contactor is used for backfeed protecon and must comply

with IEC/EN 62040-1 (the creep age and clearance distances shall meet the

basic insulaon requirements for pollution degree 2).

⚫ Disconnecon and overcurrent protecon devices shall be provided by others

for permanently connected AC input (Normal AC/Bypass AC) and AC output

circuits.

⚫ Check that the indicaons on the rang plate correspond to your AC powered

system and to the actual electrical consumpon of all the equipment to be

connected to the system.

⚫ For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the

equipment and shall be easily accessible

⚫ Never install the system near liquids or in an excessively damp environment.

⚫ Never let a foreign body penetrate inside the system.

⚫ Never block the venlaon grates of the system.

⚫ Never expose the system to direct sunlight or source of heat.

⚫ If the system must be stored prior to installaon, storage mus t be in a dry

place.

⚫ The admissible storage temperature range is -25°C to +60°C with baery(-15°C

to +40°C without baery).

Special precauons

⚫ The unit is heavy: wear safety shoes and use vacuum lier preferenally for

handling operaons.

⚫ All handling operaons will require at least two people (unpacking, lif ng,

installaon in rack system).

⚫ Straps are provided only for unpacking manually the unit from the carton;

don’t use the straps to carry the unit around. The unit can slip from the straps

during handling (risk of injury and product damage):

- keep 12in / 30cm minimum distance between the straps

- li the unit carefully and keep it at low height

- keep the unit horizontal during unpacking.

⚫ Before and aer the installaon, if the UPS remains de-energized for a long

period, the UPS must be energized for a period of 24 hours, at least once every

6 months (for a normal storage temperature less than 25°C). This charges the

baery, thus avoiding possible irreversible damage.

⚫ During the replacement of the Baery Module, it is imperave to use the same

type and number of element as the original Baery Module provided with the

UPS to maintain an idencal level of performance and safety.

Contents

1. Introducon ....................................................................................................1

1.1 Environmental protecon ...........................................................................1

2. Presentaon ....................................................................................................3

2.1 Front panel ................................................................................................3

2.2 Rear panels ................................................................................................4

2.3 Circuit diagram...........................................................................................6

3. Installaon ......................................................................................................7

3.1 Inspecng the equipment...........................................................................7

3.2 Unpacking the Unit ....................................................................................7

3.3 Checking the accessory kit ..........................................................................9

3.4 Install the unit ............................................................................................9

4. Power cables connecon ...............................................................................14

4.1 Access to terminal blocks(AC source to UPS) .............................................15

4.2 Access to terminal blocks(PDU source to R/T UPS)(Oponal) .....................16

4.3 Parallel Installaon and Operaon(Oponal) .............................................16

5. Operaon ......................................................................................................22

5.1 Control panel ...........................................................................................22

5.2 LCD descripon ........................................................................................24

5.3 Display funcons ......................................................................................27

5.4 User sengs ............................................................................................27

5.5 UPS startup and shutdown .......................................................................28

5.6 LCD operaon ..........................................................................................30

6. Communicaon .............................................................................................38

6.1 Communicaon ports ...............................................................................38

6.2 Network Management Card (Oponal) .....................................................39

6.3 UPS Management Soware ......................................................................39

7. UPS maintenance...........................................................................................40

7.1 Equipment care ........................................................................................40

7.2 Transporng the UPS ................................................................................40

7.3 Storing the equipment .............................................................................40

7.4 Replacing baeries ...................................................................................41

7.5Recycling the used equipment ...................................................................42

8. Troubleshoong.............................................................................................43

8.1 Typical alarms and faults ..........................................................................43

8.2 Silencing the alarm ...................................................................................47

9. Speciﬁcaons.................................................................................................48

9.1 Model speciﬁcaons ................................................................................48

10 Glossary........................................................................................................53

1. Introducon

Thank you for selecng UPS to protect your electrical equipment. The UPS has

been designed with the utmost care.

We recommend that you take the me to read this manual to take full

advantage of the many features of your UPS (Uninterrupble Power System).

Before installing your UPS, please read the booklet presenng the safety

instrucons. Then follow the indicaons in this manual.

1.1 Environmental protecon

Products are developed according to an eco-design approach.

Substances

This product does not contain CFCs, HCFCs or asbestos.

Packing

To improve waste treatment and facilitate recycling, separate the various

packing components.

• The cardboard we use comprises over 50% of recycled cardboard.

• Sacks and bags are made of polyethylene.

• Packing materials are recyclable and bear the appropriate idenﬁcaon

symbol

Materials Abbreviaons Number in

the symbol s

Polyethylene terephthalat

PET 01

High-density polyethylene

HDPE 02

Polyvinyl chloride

PVC 03

Low-density polyethylene

LDPE 04

Polypropylene

PP 05

Polystyrene

PS 06

Follow all local regulaons for the disposal of packing materials.

Product

The product is made up of recyclable materials.

Dismantling and destrucon must take place in compliance with all local

regulaons concerning waste. At the end of its service life, the product must be

transported to a processing center for electrical and electronic waste.

Baery

The product contains lead-acid baeries that must be processed according to

applicable local regulaons concerning baeries.

The baery may be removed to comply with regulaons and in view of correct

disposal.

1.2 Electronic equipment protecon

The uninterrupble power system (UPS) protects your sensive electronic

equipment from the most common power problems, including power failures,

power sags, power surges, brownouts, line noise, high voltage spikes,

frequency variaons, switching transients, and harmonic distoron.

Power outages may occur unexpected, and the power quality will be errac.

These power problems have the potenal to corrupt crical data, destroy

unsaved work sessions, and damage hardware - causing hours of lost

producvity and expensive repairs.

With the UPS, you can safely eliminate the eﬀects of power disturbances and

guard the integrity of your equipment. Providing outstanding performance and

reliability, UPS’s unique beneﬁts include:

⚫ True online double-conversion technology with high power density, ulity

frequency independence, and generator compability.

⚫ Selectable High Eﬃciency mode of operaon.

⚫ Standard communicaon opons: one RS232 communicaon port, one

USB communicaon port, one dry in port and dry out port.

⚫ Oponal connecvity cards with enhanced communicaon capabilies.

⚫ Firmware that is easily upgradable without a service call.

2. Presentaon

2.1 Front panel

Tower model:

Tower UPS 6KS/10KS Tower UPS 6K/10K Tower EBM

RT model:

RT UPS 6K/6KS/10K/10KS UPS RT EBM

2.2 Rear panels

Tower model:

Tower UPS 6KS Tower UPS 10KS

Tower UPS 6K Tower UPS 10K Tower EBM

1. Intelligent slot

2. USB

3. RS232

4. RJ11 (only for RT model)

5. EPO

6. Parallel card (oponal)

7. Dry IN/OUT

8. Input /Output terminal

(Standard model 5pole, IPL, IPN, P E,

OPL, OPN; long backup model has 2

version , one is 5 Pole. Another is 7pole.

7pole add bat+, bat-, and no external

baery connector #10.)

9. Input switch

10. External baery connector

11. Maintenance bypass switch (oponal)

12. EBM connector

13. EBM connector

14. Fuse board cover (replace EBM fuse)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unión Postal Universal de UPSONIC POWER

UPSONIC POWER

UPSONIC POWER Orion 850 Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario