Unit UT713 Manual de usuario
Model UT713
OPERATING MANUAL
TABLE OF CONTENTS
TITLE PAGE
3
3
4
6
6
7
8
10
12
14
15
19
19
Introduction
Unpacking Inspection
Safety Information
Turning the Calibrator On
Simulating a Thermocouple
Measuring a Thermocouple
Simulating TC or Source mV
Measure TC or mV
Cold Terminal Temperature Autocompensation
Explanation of International Symbols
Maintenance
Specifications
Temperature Measure and Thermocouple Simulate
Model UT713: OPERATING MANUAL
1
TABLE OF CONTENTS
TITLE PAGE
21
21
22
Thermocouple Standards and Scales
Millivolt Measure and Source
General Specifications
Model UT713: OPERATING MANUAL
2
Description
Operating Manual
Test Lead
Alligator Clip
9V Alkaline Battery (1604A or 6LF22)
Introduction
The UNI-T Model UT713Thermocouple Calibrator is a precise source and measurement
tool for calibrating thermocouple instruments. The calibrator sources or measures
mV or 8 different type of TC in units of , . But the Meter cannot uses as an output
source and measurement.
Item
1
2
3
4
Qty
1 piece
1 pair
1 pair
1 piece
Unpacking Inspection
Open the package case and take out the Meter, check the following items carefully
to see any missing or damaged parts:
Model UT713: OPERATING MANUAL
3
Warning
Safety Information
This Meter complies with the standard CE EN61326.
To avoid possible electric shock or personal injury:
l
l
l
l
Before using the calibrator inspect the case. Do not use the calibrator
if it is damaged or the case (or part of the case) is removed. Look for
cracks or missing plastic.
During measurement, do not contact the naked wire, connector, unused
terminal or the circuit under test.
Inspect the test leads for damaged insulation or exposed metal. Replace
damaged test leads with identical model number or electrical
specifications before using the Meter.
When using the test leads, keep your fingers behind the finger guards.
Use the Meter only as specified in this operating manual, otherwise the protection
provided by the Meter may be impaired.
lNever apply more than 30V between any two terminals, or between any
terminal and earth ground.
Model UT713: OPERATING MANUAL
4
l
l
l
l
l
l
l
Replace the battery as soon as the battery indicator appears. With a
low battery, the Meter might produce false readings that can lead to
electric shock and personal injury.
The internal circuit of the calibrator shall not be altered at will to avoid
damage of the calibrator and any accident
Do not use or store the calibrator in an environment of high temperature,
humidity, explosive, inflammable and strong magnetic field. The
performance of the Meter may deteriorate after dampened
Under the influence of Radiated, Radio-Frequency Electromagnetic Field
phenomenon, the captioned model may malfunction and can self-recover
after the test.
When servicing the Meter, use only the same model number or identical
electrical specifications replacement part.
Constantly check the battery as it may lead when it has been using for
some time, replace the battery as soon as leaking appears. A leaking
battery will damage the calibrator.
Take out the battery when not using for a long time.
Model UT713: OPERATING MANUAL
5
Figure 1
Press so that
OUTPUT is on
the display
Press and to
increment or
decrement a digit.
Press and to step
up/down from 0 to 9 .
Hold down to scroll
faster
Output
Press TYPE to
select TC type or
DC mV
Press to toggle
positive or
negative
temperature
Show TC type or
voltage range
selected
Turning the Calibrator On
Press to turn the calibrator on and off
Press to toggle
or
Press to turn
the Meter on
and off
Output Terminals
Model UT713: OPERATING MANUAL
6
Figure 2
Show TC type or
voltage range
elected
Press so that
INPUT is on the
display
Input
Press to turn the
Meter on and off
Input Terminals
Display the
selected or
Press to toggle
or
Press Type to
select TC type or
DC mV
Model UT713: OPERATING MANUAL
7
1. Press the pushbutton to turn the Calibrator on.
2. Press OUTPUT to display OUTPUT if the Calibrator is at input mode which displays
INPUT.
3. Press to select the requested TC type or DC mV range.
4. Press or to increment or decrement a digit.
5. Press or to step up or down from 0 to 9. Hold down to scroll faster.
6. Insert the test leads to the OUPUT terminals as figure 3.
7. Connect the other end of the test leads to the TC measurement equipment or the
DC mV measurement equipment.
When connecting the calibrator to the auto ranging DC mV measurement equipment
or TC measurement equipment, it must lock the range.
Note:
Model UT713: OPERATING MANUAL
8
Figure 3
Measurement
equipment
Model UT713: OPERATING MANUAL
9
Tabla de contenidos
Otros manuales de Equipo de prueba de Unit
Unit
Unit UTD1025CL Manual de usuario
Unit
Unit utd2000 Manual de usuario
Unit
Unit UT512 Manual de usuario
Unit
Unit UPO1000CS Series Manual de usuario
Unit
Unit UT12A Manual de usuario
Unit
Unit UT528 Manual de usuario
Unit
Unit UPO2000E Series Manual de usuario
Unit
Unit UT677A Manual de usuario
Unit
Unit UT526 Manual de usuario
Unit
Unit UT15A Manual de usuario
Unit
Unit UT673A Manual de usuario
Unit
Unit UT512D Manual de usuario
Unit
Unit UT3500 Series Manual de usuario
Unit
Unit UT361 Manual de usuario
Unit
Unit UT276A Manual de usuario
Unit
Unit UT3200+ Series Manual de usuario
Unit
Unit UT 4000 Series Manual de usuario
Unit
Unit UT501A Manual de usuario
Unit
Unit utd2000 Manual de usuario
Unit
Unit UT890D Manual de usuario
Manuales populares de Equipo de prueba de otras marcas
SMART
SMART KANAAD SBT XTREME 3G Series Manual de usuario
Agilent Technologies
Agilent Technologies BERT Serial Manual de usuario
Agilent Technologies
Agilent Technologies N3280A Manual de usuario
Vernier
Vernier Go Direct Voltage Manual de usuario
Lifeloc
Lifeloc R.A.D.A.R. Manual de usuario
Fluke
Fluke T5-600 Instrucciones de funcionamiento e instalación
