Unique Gas Products UGP-30E CT2 Manual de usuario

UGP-30E – CT2

Installation Instructions

Be sure the rangetop is properly installed and grounded by a qualified technician. It is the

responsibility of the technician to make certain that your rangetop is properly installed.

Situations cause by improper installation are not covered under the warranty. Any

expenses incurred due to such situations will not be paid by the manufacturer of the

rangetop.

Leak testing of the appliance shall be conducted according to the manufacturer’s

instructions, or according to local building codes and gas regulations in your area.

GAS CONNECTIONS (All Units)

NOTICE TO MASSACHUSETTS APPLIANCE DEALERS:

Be sure this document is included in all gas rangetop appliances sold to consumers in

the State of Massachusetts.

NOTICE: Massachusetts law requires the following:

 Appliances must be installed by a licensed plumber or gas fitter.

 Appliances must be connected with a three (3) foot (36” maximum length)

flexible gas connector and

 A “T” handle type manual gas valve in the gas supply line to the appliance.

Have the dealer where you purchase your new rangetop install it or have them

recommend a qualified installer. Installation must conform with local codes. In the

absence of local codes, the installation must conform with the National Fuel Gas

Code, ANSI Z223.1-Latest Edition in the U.S.A. or the CAN/CGA B149.1 or .2

Installation Codes in Canada.

The rangetop should be connected to the supply line with 1/2-inch black iron pipe

or a certified flexible type stove connector. To prevent gas leaks, put an approved

sealing compound which is resistant to liquefied petroleum gases on all threaded

connections.

Important: Do not apply pressure directly to the rangetop manifold pipe when

tightening supply connections. The manifold pipe should be held securely at the

pressure regulator to prevent twisting. Hold the pressure regulator with a wrench

during the tightening of the connection, or the manifold pipe may be twisted and

split and cause a dangerous leak.

The installation of rangetops designed for manufactured (mobile) home installation

must conform with the Manufactured Construction and Safety, Title 24 CFR, Part

3280, [formerly the Federal standard for Mobile Home Construction and Safety,

Title 24, HUD (Part 280)] in the U.S.A. or C.S.A. Standard CAN/CGA Z240.4.2 in

Canada or, when such standards are not applicable, with local codes.

UGP-30E – CT2

The installation of rangetops designed for recreational vehicle installation must

conform with state or other codes or, in the absence of such codes, with the

standard for recreational vehicles. ANSI A119.2.2–1982 in the U.S.A. or CAN/CGA

Z240.4.2 in Canada.

The installation of appliances designed for recreational park trailers must conform

with state or other codes or, in the absence of such codes, with the standard for

recreational park trailers, ANSI A119.5.

Note: Check all piping connections in the unit for leaks. Never use an open flame to

check for gas leaks. Use a soap solution, 75% water, 25% dish washing soap. It is

possible for connections made at the factory to leak, due to vibration encountered in

transportation. Make certain you have checked them all, and repair any connections

that leak.

The appliance and its individual shut-off valve must be disconnected from the gas

supply piping system during any pressure testing of that system at test pressures in

excess of ½ psig.

The appliance must be isolated from the gas supply piping system by closing its

individual manual shut-off valve during any pressure testing of the gas supply piping

system at test pressures equal to or less than 1/2 psig.

CLEARANCES

All units must be installed in accordance to minimum rear and side wall clearances

and clearances extended vertically above cooking top which are stated on the serial

plate (the serial plate is located on the back of the unit.)

Make sure that the wall coverings, countertops and cabinets around the rangetop can

withstand temperatures of up to 200˚ F/93˚ C generated by the rangetop.

 Gas line shut-off valve

To reduce the possibility of gas leaks, apply Teflon tape

or a thread compound approved for use with LP or

Natural gases to all threaded connections.

 Connect the supplied ½” threaded pipe to the units

regulator located on the back left of the unit. We suggest

using a ½” female to 3/8” male flare adaptor on the end

of the ½” threaded pipe supplied.

 Use a 5/8” flexible appliance connector to connect your

gas supply to the appliance. A 3 foot length is

recommended for ease of installation but other lengths

are acceptable. Never use an old connector when

installing a new range.

 Check for leaks using a leak detector or soapy water, 75%

water, 25% dish washing soap.

UGP-30E – CT2

It is the responsibility of the installer to make certain that the rangetop is properly

adjusted at the time of installation. Situations caused by improper adjustments or

improper installation are not covered under the warranty. Any expenses incurred due

to such situations will not be paid by the manufacturer of the appliance.

Note:Basedon24”(61cm)deepcabinet

 This rangetop may be installed directly adjacent to existing 36” (91.4 cm)

high base cabinets.

 The rangetop CANNOT be installed directly adjacent to sidewalls, tall

cabinets, tall appliances, or other side vertical surfaces above 36” (91.4 cm)

high. There must be a minimum of 6” (15.2 cm) side clearance from the

UGP-30E – CT2

rangetop to such combustible surfaces above the 36” (91.4 cm) counter

height.

 Within the 6” (15.2 cm) side clearance to combustible vertical surfaces above

36” (91.4 cm), the maximum wall cabinet depth must be 13” (33.0 cm) and

wall cabinets within this 6” (15.2 cm) side clearance must be 18” (45.7 cm)

above the 36” (91.4 cm) high countertop.

 Wall cabinets above the rangetop must be a minimum of 42” (106.7 cm)

above the rangetop cooking surface for the full width of the rangetop. This

minimum height requirement does not apply if a rangetop hood is installed

over the cooking surface.

Wall Installation

If a range hood is installed above the rangetop, maintain a 30” (76.2 cm) minimum

clearance between the rangetop and the bottom of the range hood. The range hood

must exhaust outside. For best smoke elimination, the lower edge of the hood

Note: Minimum clearance for back wall

is 0” with backguard or high shelf.

UGP-30E – CT2

should be installed a minimum of 30” to a maximum of 36” above the cooktop

surface. Recommended CFM should be g 450 cfm for the 30” rangetop.

Do not install with a downdraft ventilation system



IslandInstallation



 This rangetop may be installed directly adjacent to existing 36” (91.4 cm)

high base cabinets.

 The rangetop CANNOT be installed directly adjacent to sidewalls, tall

cabinets, tall appliances, or other side vertical surfaces above 36” (91.4 cm)

Note:

here must be a minimum of 6” (15.2 cm) clearance from rear of rangetop to a

combustible wall. Clearances from non-combustible materials are not part of the ANSI Z21.1

scope and are not certified by CSA. Clearances to non-combustible materials must be approved

by the authority having jurisdiction.

UGP-30E – CT2

high. There must be a minimum of 6” (15.2 cm) side clearance from the

rangetop to such combustible surfaces above the 36” (91.4 cm) counter

height.

 Within the 6” (15.2 cm) side clearance to combustible vertical surfaces above

36” (91.4 cm), the maximum wall cabinet depth must be 13” (33.0 cm) and

wall cabinets within this 6” (15.2 cm) side clearance must be 18” (45.7 cm)

above the 36” (91.4 cm) high countertop.

 Wall cabinets above the rangetop must be a minimum of 42” (106.7 cm)

above the rangetop cooking surface for the full width of the rangetop. This

minimum height requirement does not apply if a rangetop hood is installed

over the cooking surface.

Make sure there is a power outlet within the reach of the rangetop’s power supply

cable (within 36 "/30 cm from the right side of the rangetop). The outlet should be

accessible with the rangetop installed.

UGP-30E – CT2

Make the countertop cut-out following the dimensions given in the illustration

above. Base below rangetop must be of a non-combustible material.

UGP-30E – CT2

Installing the Rangetop

 Remove the rangetop from its package and set aside all burners, burner caps

and grates.

 Gently slide in the cooktop into the cut-out, make sure your cut-outs are

there for the gas connection and electrical hookup (if you choose to use it).

 Once this is done you’re now ready to slide the rangetop all the way back to

the wall.

 Install all burners and burner caps

 Install all grates.

Connecting gas to rangetop

This rangetop is designed to operate at a pressure of 4” of water column on natural

gas or 10” of water column on propane gas (LPG).

Make sure you are supplying your rangetop with the type of gas for which it is

designed. It’s shipped for use with NG. This rangetop is convertible for use on

natural gas (LPG) also. When using this rangetop on LPG gas, conversion must be

made by a qualified LPG installer before attempting to operate the rangetop on that

gas.

For correct operation, the pressure of natural gas supplied to the regulator should be

between 4” and 5” of water column. For LP gas, the pressure supplied must be

between 10” and 12” of water column.

When checking for correct operation of the regulator, the inlet pressure must be at

least 1” more than the operating manifold pressure as given above.

The pressure regulator located at the inlet of the rangetop manifold must remain in

the supply line regardless of whether Natural (NG) or Propane (LP) gas is being

used.

A flexible metal appliance connector used to connect the rangetop to the gas supply

should be 3 feet/91.4 cm max. in length for easy installation. In Canada, flexible

connectors should be single wall metal connectors less than 6 feet/182.9 cm in

length.

Shut off the main gas supply valve before removing the old cooking appliance (if

applicable) and leave it off until the new hook-up has been completed. Don’t forget

to relight the pilots on other gas appliances when you turn the gas back on.

Because hard piping restricts movement of the rangetop, the use of a CSA certified

flexible metal appliance connector is recommended unless local codes require a hard-

UGP-30E – CT2

piped connection. Never reuse an old connector when installing a new rangetop. If

the hard piping method is used, you must carefully align the pipe.

To prevent gas leaks, use pipe joint compound resistant to NG gases on all male

external pipe threads.

1. In an easily accessible location, install a service manual gas shut off valve. Be

sure everyone operating the rangetop knows where and how to shut off the

gas supply to the cook top.

2. Use a flexible gas line to connect to the 1/2” fitting, located on the bottom

right hand corner underneath the rangetop.

3. When all connections have been made, be sure all rangetop controls are in

the off position and turn on the main gas supply valve. Check for gas leaks

by using a 75% water, 25% dish washing soap solution. If a gas leak is

present, shut off gas immediately, tighten all connections, and retest for

leaks.

4. Any opening in the wall behind the appliance and in the floor under the

appliance shall be sealed.

Otros manuales para UGP-30E CT2

Tabla de contenidos

Otros manuales de Quemador de Unique Gas Products

Unique Gas Products

Unique Gas Products UGP-30E CT2 Manual de usuario

Manuales populares de Quemador de otras marcas

Siemens

Siemens EX875KYV1E Hoja de especificaciones

AEG

AEG CERAMIC HOB 6010 K Manual de usuario

VALERA

VALERA CT 70A Manual de usuario

Zanussi

Zanussi ZGF 6420 Manual de usuario

Gaggenau

Gaggenau CI 273 Manual de usuario

G3 Ferrari

G3 Ferrari Energy Manual de usuario

Pkm

Pkm IN4B Manual de usuario

Award

Award H903BG Manual de usuario

Zanussi

Zanussi VCH 5005 RZ Manual de usuario

Miele

Miele KM 523 Manual de usuario

Hotpoint

Hotpoint IS67V8CCXT/E Manual de usuario

AEG

AEG HK854870XB Manual de usuario

Cookology

Cookology SEP600BK Manual de usuario

Bauknecht

Bauknecht Hob Manual de usuario

Zanussi

Zanussi ZGM 782 Manual de usuario

dipo INDUCTION

dipo INDUCTION DIBK218S Manual de usuario

Miele

Miele KM 5987 Manual de usuario

Miele

Miele KM 360 G Manual de usuario