Uniden UWG700 Manual de usuario
UWG700
Gate Keeper
Video Intercom
For more exciting new products please visit our website:
Australia: www.uniden.com.au
New Zealand: www.uniden.co.nz
UWG700 OM.indd 1 28/9/11 9:41:33 AM
2
UWG700 OM.indd 2 28/9/11 9:41:34 AM
3
If any items are missing or damaged, contact your place of purchase immediately.
Never use damaged products!
Need Help? Get answers at our website:
www.uniden.com.au for Australian model
www.uniden.co.nz for New Zealand model
What's in the box?
UWG700 Digital Wireless Gatekeeper
System Owner’s Manual
7inch LCD Colour Display monitor
AC adaptor
(small)
Not shown:
Mounting hardware
AV cable
Gatekeeper camera/intercom
AC adaptor
(large)
Not shown:
- 2 wire power cable
- 1m cable (for optional
door strike)
- Mounting hardware
UWS1117 Owner’s Manual
UWG700 OM.indd 3 28/9/11 9:41:35 AM
4
Important Safety Instructions!
This manual contains important information about this product’s operation. If you are installing
this product for others, you must leave this manual or a copy with the end user.
When using your equipment, always follow basic safety precautions to reduce the risk of re, electric shock
and injury to persons, including the following:
This equipment is NOT waterproof. DO NOT expose it to rain or moisture (the camera’s front housing is
►
weatherproof when mounted correctly. DO NOT expose it to excessive water or moisture).
DO NOT immerse any part of the product in water. Do not use this product near water, e.g., near a bath
►
tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
To avoid any risk of electric shock from lightning, avoid handling any electronic devices (except battery
►
powered ones) during an electrical storm.
Use only the power cord and/or batteries indicated in this manual. Never dispose of any batteries in a re:
►
they may explode. Check with local codes for possible special disposal instructions.
Never tug or pull on any power cord: be sure to leave some slack in the cord when placing your
►
equipment, and always use the plug to unplug cord from the wall outlet.
Never leave power cords where they can become crushed, cut, or frayed; when running power cords,
►
avoid letting them rub against any sharp edges or lie across any high trac areas where people might trip
over them.
Do not use the device if the adapter cords or plugs have been damaged, the unit has been exposed to
►
liquids, or the unit has been dropped or is damaged.
Warnings to Parents and Other Users
Failure to follow these warnings and the assembly instructions could result in serious injury or death. This
product is not designed or intended for use as a medical monitor, nor should this product be used as a
substitution for medical or parental supervision. Always be sure that both the transmitter and receiver are
working properly and are within range of each other.
STRANGULATION HAZARD. Keep the adapter cords out of the reach of children.
►
WARNING: KEEP OUT OF THE REACH OF CHILDREN. Allow for proper ventilation when units are in use. Do►
not cover the camera or receiver with any object such as a blanket. Do not place it in a drawer or in any
location which would mue the sound or interfere with the normal ow of air.
SAVE THESE INSTRUCTIONS!
UWG700 OM.indd 4 28/9/11 9:41:36 AM
5
Contents
Important Safety Instructions! ................................. 4
Warnings to Parents and Other Users................................. 4
For best results:........................................................................... 5
GETTING STARTED..................................................... 6
Mounting and Plugging in the Monitor............................. 6
Wall Mounting your Monitor. ................................................ 6
Standing Monitor up on a Table........................................... 7
Plugging Monitor into Another Monitor ........................... 7
Mounting and Plugging in the Camera ............................. 8
Plugging Camera In................................................................... 8
Battery Powering the Camera................................................ 9
Mounting the Camera ............................................................10
Connecting the Camera to an Optional Electronic Door
Strike.........................................................................................11
CONTROLS AND
CONNECTIONS...................................................... 12
SCREEN ICONS .........................................................16
BASIC OPERATION................................................... 17
PAIRING THE CAMERA AND MONITOR ..................19
MAIN MENU..............................................................20
CAMERA SETUP........................................................20
RECORD SETUP ........................................................22
EVENT LIST AND PLAYBACK ...................................24
SYSTEM SETUP.........................................................25
COMPUTER VIEWING...............................................28
Solving Problems.................................................... 29
Additional Information........................................... 33
One-year Limited Warranty.................................... 34
For best results:
To avoid damage to your equipment, follow these simple precautions:
Do not drop, puncture or disassemble any part of the equipment. There are no user-serviceable parts
►
inside.
Do not expose the equipment to high temperatures, and avoid leaving the equipment in direct sunlight
►
for more than a few minutes. Heat can damage the case or electrical parts.
Do not place heavy items on top of the equipment or expose the equipment to heavy pressure.
►
Remove the power adapter during long periods between usages.►
Clean only with a dry cloth.►
Failure to follow the instructions in this operating manual will void the warranty. Uniden assumes
no liability for damages to property or injury to persons caused by improper handling or failure to
comply with these safety instructions.
UWG700 OM.indd 5 28/9/11 9:41:36 AM
6
GETTING STARTED
The UWG700 comes included with mounting hardware, cables, AC adaptors and screwdriver with
security head. A Philips head and flat head screwdriver (not included) will also be required for
installation.
Mounting and Plugging in the Monitor
The monitor is able to be mounted on a wall using the wall mount or it can be rested on a table top using
the attached table stand.
Wall Mounting your Monitor
Choose a desired mounting location for the monitor station and1.
fasten the mount using the included mounting hardware. Ensure
that the tabs (for sliding on the monitor) are facing outwards and
the hooks are pointing up.
Important: Make sure the mounting location is at an appropriate level
for you to access the buttons, easily view the LCD screen and is close
enough to a power source to be plugged in
Plug the jack of the small AC adaptor into the back of the monitor2.
(labeled DC IN).
Note: Make sure to connect the smaller of the two AC adaptors to the
monitor - as a safety measure only the smaller AC adaptor will fit.
Plug the other end into a surge protected power source.3.
Slide the monitor onto the wall mount by inserting the four tabs4.
from the wall mount into the four slots on the back of the monitor.
Be sure to slide the monitor into place.
Hang Monitor Mount at
appropriate level
Plug Monitor in
UWG700 OM.indd 6 28/9/11 9:41:37 AM
7
Standing Monitor up on a Table
Pull the table stand away from the back of the monitor and place1.
monitor on a flat level surface with the stand.
Note: Make sure that the flat surface is close to a power source so it
can be plugged in
Pull the bottom side of the stand away from the monitor and stand2.
the monitor up on a table.
Plug the jack of the small AC adaptor into the back of the monitor3.
(labeled DC IN).
Note: Make sure to connect the smaller of the two AC adaptors to the
monitor - as a safety measure only the smaller AC adaptor will fit.
Plug the other end of the power cable into a power source (surge4.
protecting power source is recommended) .
Plugging Monitor into Another Monitor
The monitor comes equipped with an audio/video output jack for connecting to an optional external
monitor or A/V device.
Note: when the A/V cable is connected the display and/or audio switches to the externally connected
device. The Talk feature (microphone) remains at the main monitor.
Monitor Stand
UWG700 OM.indd 7 28/9/11 9:41:37 AM
8
Mounting and Plugging in the Camera
Using the AC adaptor is the recommended method of powering the Camera. The placement of the camera
should be within reach of a power point.
Note: The camera can also operate in a limited capacity using batteries.
Note: The camera is NOT WATERPROOF. The camera’s front housing is weatherproof when mounted
correctly, DO NOT expose it to excessive water or moisture.
Plugging Camera In
Unscrew and remove the small backing on the lower back of the1.
camera.
Pull the black and red wires through the hole on the plug located2.
on the small backing.
Pull the black and red wires through the provided wire holes on any3.
of the mounts you are using, starting with the flat mount first.
Using a flat head screw driver, loosen the screws for the positive4.
and negative connection, next to the words DC (first and second
connection).
Insert the black wire into the slot to the negative connection (first5.
slot) and the red wire into the positive connection (second slot).
Tighten the screws for the negative and positive connection (first6.
and second slot). Tightening the screws will lock the wires into
place.
Pull gently on the wires to ensure they are locked into the proper7.
slots.
Plug the other end of the red and black wire into the provided8.
power adapter.
Plug the power adapter into a power source.9.
Before putting the backing on, check that the camera and monitor10.
are paired (See Pairing Camera and Monitor p.19).
When the wires are in proper
slots, tighten screws
Loosen screws for Positive
and Negative Connection
UWG700 OM.indd 8 28/9/11 9:41:38 AM
9
With the wires pulled through the hole on the backing and11.
mounts, and the devices paired, screw the small backing back
onto the back of the camera.
• If connecting a door strike, please see connecting an electric
door strike before placing the backing back on camera.
Note: The devices will only pair when the camera is plugged into a
power source
Battery Powering the Camera (Optional)
Note: Using the AC adaptor is the recommended method of powering
the camera. The camera can operate in a limited capacity using
batteries; for typical operation lasting 1 minute, 5 times per day, the
system can last up to 3 months.
Remove the entire backing from the back of the camera by removing1.
the screws along the edges.
Insert 6 AA batteries into the provided battery slots.2.
Ensure that the camera and monitor are paired with one another.3.
(see Pairing on p.19.)
(Optional) Disconnect (if previously connected) the black and red4.
wires from the negative and positive slots.
Screw the backing, back onto the camera.5.
Note: Batteries are not included.
With wires pulled through rubber
plug, screw backing on
Insert 6 AA batteries in
provided space
UWG700 OM.indd 9 28/9/11 9:41:39 AM
10
Mounting the Camera
The camera can be mounted flat to a wall.
Make sure that both devices are plugged in and paired.1.
Ensure that the black and red wires are pulled through the provided2.
wire slot, located on the bottom of the flat mount.
Make sure you put the mount at an acceptable face level so that your3.
camera can view the face of the person ringing the doorbell, as well
as an appropriate height for someone to be able to push the doorbell
button down.
Once you have selected a height and location for the camera, screw the4.
flat camera mount to the location you would like the camera mounted.
Insert the camera into the mount by placing the tabs on the top of the5.
camera into the slots on the top mount.
Secure the camera into the mount by fastening the security screws,6.
using the included screwdriver with security head, on the bottom of
the camera and mount.
Screw mount into
wall at face level
Screw mount onto
Camera
UWG700 OM.indd 10 28/9/11 9:41:39 AM
Tabla de contenidos
Otros manuales de Sistema de intercomunicación de Uniden
