unGer Rinse'N'Go Max Manual de usuario
1
User Manual
Read carefully for safety, assembly
and operating instructions prior to
using this product.
2
TABLE OF CONTENTS
DANGER
READ USER MANUAL BEFORE USING PRODUCT
Introduction.......................................................................................................................... 3
1.0 Safety Information ................................................................................................. 4-5
2.0 System Products & Accessories......................................................................... 6-9
3.0 Assembly Instructions.............................................................................................10
4.0 Use and Operation............................................................................................11-12
5.0 Pure Water Production............................................................................................13
6.0 System Maintenance - Replacing Resin Filter & Care ..........................14-16
7.0 Storage .........................................................................................................................16
8.0 Environmental Information ..................................................................................16
9.0 TDS Meter....................................................................................................................17
Product Guarantee...........................................................................................................18
CONTENTS UNDER PRESSURE. CAN CAUSE SEVERE INJURY OR DEATH
FROM TANK RUPTURE. THIS PRODUCT CONTAINS A BUTTON BATTERY.
IF SWALLOWED, IT COULD CAUSE SEVERE INJURY OR DEATH IN JUST
2 HOURS. SEEK MEDICAL ATTENTION IMMEDIATELY.
WHEN STARTING SYSTEM
• WATER OUTPUT MUST BE OPEN WHEN FILLING.
• DO NOT EXCEED PRESSURE OF 115 PSI (8 BAR).
• CHECK SYSTEM FOR CRACKS.
• BE SURE COVER IS IN LOCKED POSITION.
• KEEP WATER OUTPUT OPEN AND HOLD YELLOW FASTLOCK™
LEVER DOWN TO REMOVE TRAPPED AIR FROM SYSTEM.
• FOR USE ONLY WITH TAP WATER.
BEFORE SERVICING SYSTEM
• SHUT OFF TAP WATER SUPPLY AND OPEN WATER OUTPUT.
• DISCONNECT WATER SUPPLY AND ALLOW TANK TO DRAIN.
SPILLED RESIN IS A SLIPPING HAZARD.
CLEAN UP SPILLED RESIN IMMEDIATELY.
RESIN CAN CAUSE SKIN IRRITATION
• AVOID SKIN CONTACT.
• WASH HANDS THOROUGHLY AFTER USE.
• CAN CAUSE EYE IRRITATION.
• AVOID EYE CONTACT.
• WEAR SAFETY GOGGLES.
• IN CASE OF EYE CONTACT, IMMEDIATELY FLUSH EYES
THOROUGHLY WITH CLEAN WATER.
• CONSULT DOCTOR IF SYMPTOMS PERSIST.
3
INTRODUCTION
Thank you for your purchase of the Unger Professional Rinse 'N' Go Max™
system. This manual will help you get set up and begin using your product right
away. When used as intended, this system will produce low total dissolved solids
or TDS (less than 20 ppm) pure water for auto, boat, RV and solar panels.
The science behind this product is called deionization, or ion exchange.
In this process, the minerals responsible for leaving spots on your vehicle and
windows are removed from the water. So, you can rinse the surface, walk away,
and still get spot-free and streak-free results. This water is meant to be used for
the nal rinse of your vehicle. You still need to wash dirt and grime off of your
vehicle as you would normally do when washing your vehicle. However, instead
of spending all of that time drying it by hand, you can rinse the vehicle with this
water and just walk away.
The Unger Professional Rinse 'N' Go Max™ system contains mixed bed ion
exchange resin to remove impurities out of ordinary tap water, turning it into
what is commonly referred to as pure water. Such impurities are referred to as
total dissolved solids (TDS) and are measured in parts per million (ppm).
Water is considered 100% demineralized or pure when its TDS is measured
at 0 ppm. The average TDS of drinking water is 180 ppm (see table in section
5.0). Pure water left on the surface will dry to a clean and spot-free appearance.
No power is required other than the tap water line pressure, which typically
ranges from 40-60 psi. This enables the system to produce pure water
at approximately 1.5 gallons per minute. Unger recommends testing the water
supply (TDS) before using this product at a pressure that does not exceed
115 psi (see section 4.0 for more information).
Mixed bed ion exchange resin eventually becomes exhausted and no longer
able to remove impurities. A TDS meter is included with the system to measure
the TDS level in the water that comes out of the system. TDS is a measure of
how pure the water is. Water that contains a TDS of less than 20 ppm should not
leave spotting on the car. The TDS must be less than 10 ppm for spot-free glass.
When TDS levels reach over 20 ppm the resin lter should be replaced.
Changing the resin lter is quick and easy (See section 6.0).
4
1.0 SAFETY INFORMATION
Prior to product assembly and start-up, it is essential that you observe the safety
information and instructions for installation and maintenance contained in this
manual. Unger is not liable for damage to application areas, plumbing system
components or persons. Unger is not liable for misuse or mishandling of the
product, including dropping, dragging or dismantling.
As with any equipment, care must be taken when operating and servicing the unit.
There is a risk of damage to the system due to:
• Operating and installation errors.
• Use of loose resin (overll and expansion of resin will damage unit).
• Vessel is opened incorrectly.
• Using non-Unger spare parts.
• Performing unauthorized modication to unit.
• Insufcient maintenance.
1.1 GENERAL WARNINGS:
• Never direct water towards eyes or face.
• KEEP OUT OF REACH OF CHILDREN AND PETS. Do not allow product to be
used as a toy. Close supervision is necessary when any appliance is used by or
near children.
• To prevent electrical shock, do not use near any sources of electricity, including
electric and power lines.
• Do not use on electrical equipment or appliances.
• After unpacking the product, be sure to carefully dispose of any plastic bags to
avoid injury.
• Use only as described in this manual.
• Use only manufacturer’s recommended attachments.
• Be sure cover is in locked position prior to use.
• Do not exert excessive pressure on release mechanism as breakage may occur.
• Drain the water from the unit after each use.
• Do not allow unit or resin to freeze.
• Ensure work area has sufcient water drainage.
• Turn off water supply when not in use.
• Do not drink water produced by this product.
5
1.2 WHEN STARTING SYSTEM:
• For use only with tap water.
• Do not connect to pressure washer or auxiliary pump.
• Do not exceed water pressure of 115 psi.
• Check system for cracks/damage.
• Be sure cover is in fully locked position.
1.4 INTENDED USE:
This product is designed for personal use only. Always ensure that the product
is properly assembled, regularly maintained and used only as intended.
This product is meant to be used outside and stored at a temperature between
40°F - 100°F. Use this device only for water treatment to reach an optimal water
quality for spot-free cleaning. Any other use, especially water treatment for
food production (e.g., beverages) or drinking water consumption is prohibited.
Prior to product assembly and start-up, it is essential that you observe the safety
information and instructions for installation and maintenance contained in this
manual. Unger is not liable for damage to application areas, plumbing system
components or persons. Unger is not liable for misuse or mishandling of the
product, including dropping, dragging or dismantling.
As with any equipment, care must be taken when operating and servicing the unit.
There is a risk of damage to the system due to:
• Operating and installation errors.
• Use of loose resin (overll and expansion of resin will damage unit).
• Vessel is opened incorrectly.
• Using non-Unger spare parts.
• Performing unauthorized modication to unit.
• Insufcient maintenance.
1.1 GENERAL WARNINGS:
• Never direct water towards eyes or face.
• KEEP OUT OF REACH OF CHILDREN AND PETS. Do not allow product to be
used as a toy. Close supervision is necessary when any appliance is used by or
near children.
• To prevent electrical shock, do not use near any sources of electricity, including
electric and power lines.
• Do not use on electrical equipment or appliances.
• After unpacking the product, be sure to carefully dispose of any plastic bags to
avoid injury.
• Use only as described in this manual.
• Use only manufacturer’s recommended attachments.
• Be sure cover is in locked position prior to use.
• Do not exert excessive pressure on release mechanism as breakage may occur.
• Drain the water from the unit after each use.
• Do not allow unit or resin to freeze.
• Ensure work area has sufcient water drainage.
• Turn off water supply when not in use.
• Do not drink water produced by this product.
1.3 BEFORE OPENING SYSTEM TO REPLACE RESIN:
1. Shut off tap water supply.
• Spilled resin is a slipping hazard. Clean up spilled resin immediately.
• Wash hands thoroughly after use.
• Resin can cause eye irritation. Avoid eye contact. In case of eye contact, immediately ush
eyes thoroughly with clean water. Consult doctor if symptoms persist.
3. Turn ON/OFF valve to “OFF” position.
2. Press yellow FastLock™ lever on
system head assembly.
4. Disconnect outlet hose.
Bottom
Top
6
2.0 SYSTEM PRODUCTS & ACCESSORIES
NOTE: When unpacking the product, make sure that no accessories are missing
and that none of the package contents have been damaged.
RINSE 'N' GO MAX™ DEIONIZATION SYSTEM OVERVIEW
This product can be connected to traditional garden hoses and used with
conventional car and window cleaning tools of your choice.
Resin lter tank
Handle
FastLock™ lever
(Yellow)
Handle
OUTLET CONNECTION
QuickChangeTM
Resin Filter Bag
(Packed inside unit)
Outlet
Connection plug
ON/OFF valve
INLET CONNECTION
System Head Assembly
Base
(Water out)
(Water in)
7
SOAP BLASTING NOZZLE OVERVIEW
Spray delivery
Soap container
Flow control
knob
Spray pattern
selector
Locking
trigger
TDS METER OVERVIEW
Battery
compartment
Hold
Maximum immersion level
TDS meter electrode
LCD
Temperature
On/Off
Protective cap
Soap Blasting Nozzle
connects to the outlet
hose (not provided)
8
SYSTEM PRODUCTS & ACCESSORIES
WATER-FED POLE & SOFT WASH BRUSH
Water-fed pole
Water-fed
soft wash brush
Water ow
ON / OFF
valve
Non-slip grip foam
Pole connects to the
outlet hose (not provided)
9
WATER-FED POLE & SOFT WASH BRUSH
INLET HOSE AND CONNECTION PLUGS
Water supply hose connects
to the inlet connection
(ON/OFF valve)
Water supply hose
Garden hose
(not provided)
QUICK CONNECT PLUGS
Water supply hose
ON/OFF valve
Inlet Adapters Outlet Adapters
Outlet
garden hose
(male plug)
Outlet female plug
Water supply hose
(provided)
Inlet plug
(male plug)
10
• Unpack Unit: Inspect the Unger
Professional Rinse 'N' Go Max™ system
and all components to ensure there are
no cracks or other damage. Read all
warnings and manual.
• Ensure there is a resin lter inside the
unit. (For instructions on how to open
the unit, see section 6.0).
• Water INPUT connection must always
be at the bottom (base) of the unit.
• Water OUTPUT connection must always
be at the top of the unit. This is the hose
that delivers ltered water.
3.0 ASSEMBLY INSTRUCTIONS
WATER OUTPUT
WATER INPUT
(Water supply)
(Connects to Soap Blasting
Nozzle or Water-fed Pole)
If leaking or dripping occurs around
the hose connections, re-tighten
the connections by hand.
Tabla de contenidos
