Ultra electronics 3503-1002 Manual de usuario
Ultra Electronics Card Systems Quick Start Guide
MAGICARD Sprinter Flip Page 1
MAGICARD Sprinter Flip
(inc. Mag Encoding option)
Quick Start Guide
Printer/Software Setup
Iss. 02 Dec 97
3503-22-01
Stock No. M9004-071
Quick Start Guide Ultra Electronics Card Systems
Page 2 MAGICARD Sprinter Flip
Setting up your MAGICARD Sprinter Flip
takes just three easy steps:
1. Unpack and install the printer
A Preparing a Location for the Printer
B Removing the Printer from the Box
C Checking the Package Contents
D Install the Dye Film
E Load the Plastic Cards
F Connect the Printer to a Power Supply
G Test the Printer Operation
H Install the Parallel Interface Cable
2. Load the supplied WINDOWS Driver software.
Ix Install the WINDOWS Driver (WINDOWS 3.x)
Iy Install the WINDOWS Driver (WINDOWS 95)
J Printer Setup
3. Verify computer-to-printer operation.
K Verifying Computer to Printer Communication in WINDOWS
L In case of Difficulty
M Important Cleaning procedures.
Note: The Ultra WEB site at http://www.ultra.co.uk contains comprehensive technical support information
including the latest downloadable software, WINDOWS Drivers, Technical Bulletins etc
Conventions
Throughout this guide, the following conventions are used to identify important
information.
WARNING - Warning messages indicate where personal injury could result from
not following the correct procedures.
CAUTION - Caution messages indicate where damage to equipment could result
from not following the correct procedures.
NOTE - Notes convey important information that is identified within the text.
Ultra Electronics Card Systems Quick Start Guide
MAGICARD Sprinter Flip Page 3
•A clean, level surface.
•Adequate space for:
- opening the Card Collection Door
- opening the Top Cover
- cable access at the rear.
- allowance for air circulation.
•An adequately ventilated room.
Preparing a Location
for the Printer
Location Requirements for your printer:
A
Quick Start Guide Ultra Electronics Card Systems
Page 4 MAGICARD Sprinter Flip
•An adequate power supply.
•Ambient temperature +10 to +30 deg C.
•Relative Humidity 20/70% RH.
•Protection from direct sunlight and
chemicals.
•Protection from abrupt temperature
changes.
Top Cover
Card Collection
Door
Ultra Electronics Card Systems Quick Start Guide
MAGICARD Sprinter Flip Page 5
Carefully open the box and remove any
accessories.
Open the front door and remove the
metal shipping clip from the chassis.
Place on a smooth, level table and
remove the polyethylene container.
Removing the Printer
from the Box
B
1
B
3
2
Quick Start Guide Ultra Electronics Card Systems
Page 6 MAGICARD Sprinter Flip
The MAGICARD Sprinter Flip
A Roll of Dye Film and a Take-up Core
(Only supplied as standard with certain Models)
The Card Cassette
Checking the
Package Contents
Locate each item as listed below:
CC
1
3
2
Ultra Electronics Card Systems Quick Start Guide
MAGICARD Sprinter Flip Page 7
A Power Cord with Molded Plug for your
Country
4
Quick Start Guide Ultra Electronics Card Systems
Page 8 MAGICARD Sprinter Flip
Envelope containing this Quick Start
Guide and the PrintMAGIC WINDOWS
Driver 3.5" floppy disk.
Envelope containing 5 Cleaning Cards
and 1 Thermal Printhead Cleaning Pen.
56
Ultra Electronics Card Systems Quick Start Guide
MAGICARD Sprinter Flip Page 9
Open the Printer Cover by lifting the
"Dzus" fastener ring and turning a
quarter turn anti-clockwise. Remove the
Dye Film carrier.
Replace the Film Carrier
Open the Dye Film package. Fit the dye
film on the lower boss, observing the
Install the
Dye Film D
1
3
2
Quick Start Guide Ultra Electronics Card Systems
Page 10 MAGICARD Sprinter Flip
correct orientation of the dye film.
Fit the empty take-up core on the upper
boss, observing the correct orientation of
the notches on the Take-up Core.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Impresora de Ultra electronics
Ultra electronics
Ultra electronics Magicard Pronto Manual de usuario
Ultra electronics
Ultra electronics Magicard Latin Series Manual de lista de piezas
Ultra electronics
Ultra electronics M9005-724 Manual de usuario
Ultra electronics
Ultra electronics Magicard Rio 2E Manual de usuario
Ultra electronics
Ultra electronics ID Card Printer Manual de usuario
Ultra electronics
Ultra electronics MAGICARD Sprinter Manual de lista de piezas
Ultra electronics
Ultra electronics Magicard Opera 100 Manual de usuario
Ultra electronics
Ultra electronics MAGICARD 300 Manual de usuario
Ultra electronics
Ultra electronics MAGICARD 300plus Manual de usuario
Ultra electronics
Ultra electronics Magicard ALTO Manual de usuario
