ULTIMATE SPEED 316940 1810 Manual de usuario

CAR BATTERY CHARGER ULGD 5.0 A1

CAR BATTERY CHARGER

Translation of original operation manual

ΦΟΡΤΙΣΤΉΣ ΜΠΑΤΑΡΙΑΣ

ΑΥΤΟΚΙΝΉΤΟΥ

Μετάφραση των αυθεντικών οδηγιών λειτουργίας

KFZ-BATTERIELADEGERÄT

Originalbetriebsanleitung

IAN 316940_1810

GB/IE/NI/CY Translation of original operation manual Page 1

GR/CY Μετάφραση των αυθεντικών οδηγιών λειτουργίας Σελίδα 11

DE/AT / CH Originalbetriebsanleitung Seite 21

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τις δυο σελίδες με τις εικόνες και εξοικειωθείτε με όλες τις

λειτουργίες της συσκευής.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

ULGD 5.0 A1 GB│IE│NI│CY │ 1 ■

Contents

Introduction............................................................ 2

Intended use........................................................................2

Scope of delivery ....................................................................2

Parts description .....................................................................2

Technical Data ......................................................................2

Safety ................................................................2

Safety instructions....................................................................2

Additional safety instructions ...........................................................3

Operation .............................................................4

Before use .........................................................................4

Connecting.........................................................................4

Disconnect .........................................................................5

Measuring STANDBY / Battery voltage...................................................5

Revitalising .........................................................................5

Program selection....................................................................5

Program 1 „6 V“ (7,3 V / 0,8 A)........................................................5

Program 2 „12 V“ (14,4 V / 0,8 A) ................................................... 6

Program 3 „12 V“ (14,4 V / 5,0 A) ................................................... 6

Program 4 „12 V“ (14,7 V / 5,0 A) ..................................................6

Retention charge ....................................................................6

Appliance protection function ..........................................................6

Maintenance and care ...................................................6

Kompernass Handels GmbH warranty .....................................7

Service ............................................................................8

Importer ...........................................................................8

Disposal...............................................................9

Translation of the original Conformity Declaration...........................10

ULGD 5.0 A1

■ 2 │ GB│IE│NI│CY

CAR BATTERY CHARGER

ULGD5.0A1

Introduction

We congratulate you on the purchase of your new

device. You have chosen a high quality product.

The instructions for use are part of the product.

They contain important information concerning

safety, use and disposal. Before using the product,

please familiarise yourself with all of the safety in-

formation and instructions for use. Only use the unit

as described and for the speciﬁed applications.

If you pass the product on to anyone else, please

ensure that you also pass on all the documentation

with it.

Intended use

The Ultimate Speed ULGD5.0A1 is a multi-stage

car battery charger that is suitable for charging

and trickle charging up of 6V or 12V lead-acid

batteries (batteries) with electrolyte solution (WET),

electrolyte absorbent mats (AGM) or gel electrolyte

(GEL).

This appliance is not suitable for charging lithium-ion

batteries. The is not intended for commercial use

and is for indoor use only.

The manufacturer accepts no responsibility for

damage(s) arising out of usage contrary to the

instructions speciﬁed below.

Scope of delivery

1 Car battery charger

1 Instructions for use

Parts description

See Figure A:

12 V / 0.8 A (Program 2)

12 V / 5.0 A (Program 3)

12 V / 5.0 A (Program 4)

6 V / 0.8 A (Program 1)

LED reverse connection

LED stand-by

Charge display

Condition display

Voltage display

Program selection button (►►►)

See Figure B:

Charger

Stands

Mains lead

Positive pole clamp (red)

Negative pole clamp (black)

Positive pole connector cable (red)

Negative pole connector cable (black)

Technical Data

Rated voltage: 220-240 V ∼ 50 Hz

(alternating current)

Rated power

consumption: 0.8 A

Rated output

DC voltage: 6 V /12 V

(direct current)

Rated output DC: 0.8 A/5.0 A

Fuse (internal): 2 A

T2A

Environmental

temperature: -20°C bis 50°C

Protection rating: IP 65

Protection class: II / (double shielded)

Battery types: 6 V lead acid battery

1.2 Ah-14 Ah

12 V Lead acid battery

1.2 Ah-120 Ah

Safety

Safety instructions

WARNING!

► Read all safety warnings and all instructions.

Failure to follow the warnings and instruc-

tions may result in electric shock, ﬁre and/or

serious injury.

This charger is suitable for indoor

use only.

ULGD 5.0 A1 GB│IE│NI│CY │ 3 ■

■ This appliance may be used by chil-

dren aged 8 over and by persons

with reduced physical, sensory or

mental capabilities or lack of expe-

rience and knowledge, provided

that they are under supervision

or have been told how to use the

appliance safely and are aware of

the potential risks. Children must not

use the appliance as a plaything.

Cleaning and user maintenance

tasks may not be carried out by

children unless they are supervised.

■ If the supply cord is damaged, it must

be replaced by the manufacturer, its

service agent or similarly qualiﬁed

persons in order to avoid a hazard.

Additional safety instructions

■ Do not use the charger for charging

non-rechargeable batteries.

■ Do not use the charger for charging

lithium-ion batteries.

■ Place the removed battery in a well-

ventilated location during charging.

■ The automatic mode of operation

and usage restrictions are explained

below in these operating instruc-

tions.

DANGER OF ELECTRIC SHOCK!

■ Do not operate the appliance with

a damaged cable, supply cord or

mains plug. A damaged power cord

causes danger to life by electric shock.

■ Before connecting to the power,

ensure that the power connection is

earthed, is 230 V ∼, 50 Hz, and is

16 A fused and equipped with an

RCCB switch (residual current circuit

breaker) in accordance with the cur-

rent regulations!

■ Disconnect the charger from the grid,

before you make or break connec-

tions to the battery.

■ Always connect the positive terminal

clamp (red) ﬁrst.

■ The negative terminal clamp (black)

must be connected to the chassis at

least 10 cm away from the battery

and the fuel line.

■ Now connect the charger to the

power supply.

■ After charging, disconnect the

charger from the grid. Only after this

remove the clamp from the bodywork.

Following this, remove the clamp

from the battery.

DANGER OF EXPLOSION

AND FIRE HAZARD!

Protect yourself from a highly explo-

sive hydrogen-oxygen reaction!

■ Ensure that during charge and

charge retention procedures, there

are no naked lights (ﬂames, cinders

or sparks)!

■ Ensure that the plus cable does not

come into contact with fuel lines

(e.g. petrol pipe)!

ULGD 5.0 A1

■ 4 │ GB│IE│NI│CY

■ Ensure that there is no possibility of

ignition of explosive or ﬂammable

substances, such as petrol or solvents,

while using charger!

■ Ensure that there is adequate venti-

lation during charging.

DANGER OF CHEMICAL

BURNS!

■ Wear protective glasses! Wear

protective gloves! If eyes or skin has

come into contact with battery acid,

rinse the aﬀected body region oﬀ

with a large amount of clean water

and consult a doctor straight away!

■ Avoid causing a short circuit when

connecting the charger to the bat-

tery. Connect the negative pole

connector cable only to the nega-

tive battery or to the body work.

Connect the positive pole connector

cable only to the plus pole of the

battery!

■ Do not place the charger close to ﬁre,

heat or to places with long-term expo-

sure to temperatures over 50 °C!

■ Ensure that no fuel lines,electric

cables, hydraulic or water pipes

are damaged by the screws during

assembly of the charger!

■ Do not cover the charger with any

objects!

■ Protect the electrical contact sur-

faces of the battery from short

circuiting!

■ Only use the charger for charging

and for charge retention of 6 V /

12 V lead batteries.

Do not charge frozen batteries.

Operation

Before use

♦ Before connecting the charger, the operating

instructions must be observed.

♦ Furthermore, the instructions of the vehicle man-

ufacturer regarding a permanently connected

vehicle battery must be observed. Secure the

vehicle, switch oﬀ the ignition.

♦ Clean the battery poles. Take care that while doing

so, your eyes do not come into contact with the dirt.

♦ Ensure suﬃcient ventilation.

Connecting

NOTES

► There are two options for connecting the

charger. Connect the negative terminal

connecting cable (black) either directly to

the negative terminal of the battery or to

the bodywork. Please also bear in mind the

vehicle manufacturer’s instructions.

♦ Before starting the charging or trickle charging

procedure on a permanently installed battery in

a vehicle, ﬁrst disconnect the negative terminal

connecting cable (black) of the vehicle from the

negative terminal of the battery. The negative

terminal of the battery is usually connected to

the vehicle’s coachwork.

♦ Connect the positive pole clamp (red) of the

charger to the positive pole of the battery.

♦ Connect the negative pole clamp (black) to the

negative pole of the battery or to the bodywork.

♦ Connect the mains cable of the charger to

the mains socket.

♦ The battery voltage display shows the cur-

rent battery voltage.

♦ Should the connection of the clamps be swapped,

the LED „reverse connection“ lights up.

ULGD 5.0 A1 GB│IE│NI│CY │ 5 ■

Disconnect

♦ Disconnect the appliance from the mains supply.

♦ Remove the negative pole clamp (black)

from the negative pole of the battery or from the

bodywork.

♦ Remove the positive pole clamp (red) from

the positive pole of the battery.

Measuring STANDBY /

Battery voltage

After connection to the grid, the appliance is on

STANDBY. The standby display lights up. When

the clamps are connected, the battery voltage is

shown in the LCD (voltage display ). The segments

of the condition display are empty.

If the voltage is below 3.8 V or above 15 V, the

battery will not be charged. The display brieﬂy

shows the error message „Err“.

The appliance goes on standby.

6 V battery:

If the voltage range of the battery is measured

as between 3.7–7.3 V, only program 1 can be

selected.

12 V batteries:

If a battery is recognised in the critical voltage

range of between 7.3–10.5 V, the appliance

checks whether a fully charged 6 V battery, or a

discharged 12 V battery is present. After pressing

the program selection button to select a program,

the appliance carries out a control measurement

for about 90 sec.

The display shows:

If after about 90 sec. between 7.3–7.5 V are

detected, the 12 V battery is defective.

The appliance goes on standby.

Revitalising

If after about 90 sec. between 7.5–10.5 V are

detected, a 12 V battery is present.

Charging starts with a pulse charge for revitalis-

ing. The voltage display ﬂashes. Once 10.5 V

are reached, the appliance switches to the other

charge steps.

Revitalising is the same for all the 12 V charge

programmes.

Program selection

NOTES

► If a battery is detected in the voltage range of

between 3.7–7.3 V, the programmes 2–3–4

can not be selected. The charging process takes

place automatically. Depending on the selected

program, the characteristic charge curve is

monitored for voltage, time and temperature.

Included are the diagnostics program, revitalis-

ing mode and retention charge.

(See principle representation program 3 Fig. C)

Program max. (V) max. (A)

16 V 7,3 V 0,8 A

2*14,4 V 0,8 A

3*14,4 V 5,0 A

4*14,7 V 5,0 A

Program 1 „6 V“ (7,3 V / 0,8 A)

For charging 6 V batteries with a capacity of less

than 14 Ah.

♦ Press the program selection button , to select

program 1. The symbol „6 V“ is displayed on

the LCD. During charging, the charge display

ﬂashes and shows the progress of the charge

procedure (1–4 bars). When the battery is fully

charged, the condition display shows 4 bars.

The ﬂashing stops and the appliance automati-

cally switches to retention charge.

ULGD 5.0 A1

■ 6 │ GB│IE│NI│CY

Program 2 „12 V“ (14,4 V / 0,8 A)

For charging 12 V batteries with a capacity of less

than 14 Ah.

♦ Press the program selection button , to select

program 2. The symbol is displayed on the

LCD. During charging, the charge display

ﬂashes and shows the progress of the charge

procedure (1–4 bars). When the battery is fully

charged, the condition display shows 4 bars.

The ﬂashing stops and the appliance automati-

cally switches to retention charge.

Program 3 „12 V“ (14,4 V / 5,0

For charging 12 V batteries with a capacity of

between 14 Ah–120 Ah.

♦ Press the program selection button , to select

program 3. The symbol is displayed on

the LCD. During charging, the charge display

ﬂashes and shows the progress of the

charge procedure (1–4 bars). When the bat-

tery is fully charged, the condition display

shows 4 bars. The ﬂashing stops and the appli-

ance automatically switches to retention charge.

Program 4 „12 V“ (14,7 V / 5,0 A)

For charging 12 V batteries with a capacity of

between 14 Ah–120 Ah under cold conditions or

for charging AGM batteries.

♦ Press the program selection button , to select

program 4.

NOTE

► This program may start with a minute delay.

The symbol is displayed on the LCD.

During charging, the charge display

ﬂashes and shows the progress of the charge

procedure (1–4 bars). When the battery is

fully charged, the condition display shows

4 bars. The ﬂashing stops and the appliance

automatically switches to retention charge.

Retention charge

As described under programmes, this appliance

features the automatic retention charge. Depending

on the voltage drop of the battery, caused by

selfdischarge, the appliance reacts with diﬀerent

charge currents.

The battery can remain connected to the charger

for longer periods of time.

Appliance protection function

The charger switches the electronics oﬀ and

switches the system instantly to the basic setting,

as soon as there is an abnormal situation, such as

short circuit, critical voltage drop during charging,

broken circuit or swapped connection of the con-

nector clamps is detected.

Should the appliance become too hot during

charging, the output current is automatically re-

duced. This protects the appliance from damage.

Maintenance and care

WARNING! Before you carry out any

work on the battery charger always pull

the mains plug out of the mains socket.

The appliance is maintenance-free.

♦ Do not under any circumstances use solvents or

other aggressive cleaning agents.

♦ Clean the plastic surfaces of the device with a

dry cloth.

ULGD 5.0 A1 GB│IE│NI│CY │ 7 ■

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from

the date of purchase. If this product has any faults,

you, the buyer, have certain statutory rights. Your

statutory rights are not restricted in any way by the

warranty described below.

Warranty conditions

The warranty period starts on the date of purchase.

Please keep your receipt in a safe place. This will

be required as proof of purchase.

If any material or manufacturing fault occurs within

three years of the date of purchase of the product,

we will either repair or replace the product for you

or refund the purchase price (at our discretion).

This warranty service requires that you present the

defective appliance and the proof of purchase (re-

ceipt) within the three-year warranty period, along

with a brief written description of the fault and of

when it occurred.

If the defect is covered by the warranty, your prod-

uct will either be repaired or replaced by us. The

repair or replacement of a product does not signify

the beginning of a new warranty period.

Warranty period and statutory claims for

defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must

be reported immediately after unpacking. Repairs

carried out after expiry of the warranty period shall

be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accord-

ance with strict quality guidelines and inspected

meticulously prior to delivery.

The warranty covers material faults or production

faults. The warranty does not extend to product

parts subject to normal wear and tear or to fragile

parts which could be considered as consumable

parts such as switches, batteries or parts made of

glass.

The warranty does not apply if the product has

been damaged, improperly used or improp-

erly maintained. The directions in the operating

instructions for the product regarding proper use

of the product are to be strictly followed. Uses

and actions that are discouraged in the operating

instructions or which are warned against must be

avoided.

This product is intended solely for private use and

not for commercial purposes. The warranty shall

be deemed void in cases of misuse or improper

handling, use of force and modiﬁcations/repairs

which have not been carried out by one of our

authorised Service centres.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Cargador de baterías de ULTIMATE SPEED

ULTIMATE SPEED

ULTIMATE SPEED ULG 12 B3 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED ULGD 3.8 A1 Manual del propietario

ULTIMATE SPEED

ULTIMATE SPEED ULG 17 A1 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED USML 3.7 A1 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED ULGD 3.8 A1 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED ULG 3.8 B1 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED ULG 3.8 A1 BATTERY CHARGER Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED ULG 12 A2 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED ULG 3.8 A1 BATTERY CHARGER Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED ULG 12 A2 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED ULG 17 A1 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED ULGD 3.8 A1 Manual del propietario

ULTIMATE SPEED

ULTIMATE SPEED ULG 3.8 B1 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED T4X SE / KH 3033 BATTERY CHARGER Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED ULGD 5.0 A1 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED 270075 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED 403814-2201 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED ULGD 3.8 A1 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED ULG 17 A1 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED ULG 3.8 A1 BATTERY CHARGER Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED ULGD 5.0 B1 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED ULGD 5.0 A1 Manual del propietario

ULTIMATE SPEED

ULTIMATE SPEED ULG 3.8 B1 Manual de usuario

ULTIMATE SPEED

ULTIMATE SPEED ULGD 5.0 B1 Manual de usuario

Manuales populares de Cargador de baterías de otras marcas

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Manual de usuario

Enelion

Enelion Vertica Manual de usuario

RCA

RCA CHU6 Manual de usuario

ANSMANN

ANSMANN ALCT 6/24-10 Manual de usuario

Hitachi

Hitachi UC 18YRSL Guía de solución de problemas

Olympus

Olympus B-20 LPC Manual de usuario

Exibel

Exibel ZH1708143 Manual de usuario

Lenmar

Lenmar Mach 1 Manual de usuario

CTEK

CTEK MXS 5.0 Manual de usuario

ABB

ABB HT842379 Manual de usuario

Nitecore

Nitecore Superb Charger SC4 Manual de usuario

Renogy

Renogy RBC2125DS-21W Manual de usuario

Braun

Braun BWC02M Manual de usuario

CTEK

CTEK MXS 3.6 Manual de usuario

Black & Decker

Black & Decker BDV090 Manual de usuario

Trinity

Trinity DPD Manual de usuario

Hulkman

Hulkman Sigma 1 Manual de usuario

IKEA

IKEA koppla Manual de usuario